Panasonic Network Camera Bl C30a Operating Instructions
Here you can view all the pages of manual Panasonic Network Camera Bl C30a Operating Instructions. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
Operating Instructions
[For assistance, please call: 1-800-272-7033] 31
4.Click [Save] when finished.
New settings are saved.
When finished, the following page is displayed.
Note
The current network settings are shown on the Status page in the Maintenance
section (see page 79).
5.Click [Restar t].
The camera restarts, and the Top page is displayed.
Note
When you do not know the camera IP address while setting [Automatic Setup]
or [DHCP Setup], you can search the...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-30.png "Page 31
Operating Instructions
[For assistance, please call: 1-800-272-7033] 31
4.Click [Save] when finished.
New settings are saved.
When finished, the following page is displayed.
Note
The current network settings are shown on the Status page in the Maintenance
section (see page 79).
5.Click [Restar t].
The camera restarts, and the Top page is displayed.
Note
When you do not know the camera IP address while setting [Automatic Setup]
or [DHCP Setup], you can search the...")
Operating Instructions [For assistance, please call: 1-800-272-7033] 31 4.Click [Save] when finished. New settings are saved. When finished, the following page is displayed. Note The current network settings are shown on the Status page in the Maintenance section (see page 79). 5.Click [Restar t]. The camera restarts, and the Top page is displayed. Note When you do not know the camera IP address while setting [Automatic Setup] or [DHCP Setup], you can search the...
Page 32
![Page 32
Operating Instructions
32
Setting Description
Allow Access from
the Internet
(Automatic Setup
Only) Allow Access from the Internet setting automatically
configures the routers Port Forwarding setting (some
routers call it Address Translation, Static IP
Masquerade, Virtual Server or Port Mapping). To
enable Internet access to the camera, check [Yes]. In this
case, the camera automatically searches the unused port
number on your network in the order from 50000 to 50050.
To disable Internet...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-31.png "Page 32
Operating Instructions
32
Setting Description
Allow Access from
the Internet
(Automatic Setup
Only) Allow Access from the Internet setting automatically
configures the routers Port Forwarding setting (some
routers call it Address Translation, Static IP
Masquerade, Virtual Server or Port Mapping). To
enable Internet access to the camera, check [Yes]. In this
case, the camera automatically searches the unused port
number on your network in the order from 50000 to 50050.
To disable Internet...")
Operating Instructions 32 Setting Description Allow Access from the Internet (Automatic Setup Only) Allow Access from the Internet setting automatically configures the routers Port Forwarding setting (some routers call it Address Translation, Static IP Masquerade, Virtual Server or Port Mapping). To enable Internet access to the camera, check [Yes]. In this case, the camera automatically searches the unused port number on your network in the order from 50000 to 50050. To disable Internet...
Page 33
![Page 33
Operating Instructions
[For assistance, please call: 1-800-272-7033] 33
Default Gateway*1
(Static/DHCP Only) If you have the assigned Default Gateway address by your
ISP or network administrator, enter it in this data field.
Set 4 digits (0—255) and 3 periods such as
192.168.0.253. But 0.0.0.0 and 255.255.255.255 are
not available.
DNS Server
Address
*1
(Static/DHCP Only) DNS server address is required in the following conditions.
Transferring camera images by...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-32.png "Page 33
Operating Instructions
[For assistance, please call: 1-800-272-7033] 33
Default Gateway*1
(Static/DHCP Only) If you have the assigned Default Gateway address by your
ISP or network administrator, enter it in this data field.
Set 4 digits (0—255) and 3 periods such as
192.168.0.253. But 0.0.0.0 and 255.255.255.255 are
not available.
DNS Server
Address
*1
(Static/DHCP Only) DNS server address is required in the following conditions.
Transferring camera images by...")
Operating Instructions [For assistance, please call: 1-800-272-7033] 33 Default Gateway*1 (Static/DHCP Only) If you have the assigned Default Gateway address by your ISP or network administrator, enter it in this data field. Set 4 digits (0—255) and 3 periods such as 192.168.0.253. But 0.0.0.0 and 255.255.255.255 are not available. DNS Server Address *1 (Static/DHCP Only) DNS server address is required in the following conditions. Transferring camera images by...
Page 34
![Page 34
Operating Instructions
34
2.3 Using Wireless LAN
Wireless communication is possible by adjusting the settings of the wireless LAN
to those for the router. Take a note of the settings and save them for reference. For
more information about wireless setting, please refer to http://panasonic.co.jp/
pcc/products/en/netwkcam/technic/wireless/cam_set.html
1.Click [Wireless] on the Setup page.
2.Set each parameter for the Wireless Configuration.
Setting Description
SSID The SSID must be set to match the...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-33.png "Page 34
Operating Instructions
34
2.3 Using Wireless LAN
Wireless communication is possible by adjusting the settings of the wireless LAN
to those for the router. Take a note of the settings and save them for reference. For
more information about wireless setting, please refer to http://panasonic.co.jp/
pcc/products/en/netwkcam/technic/wireless/cam_set.html
1.Click [Wireless] on the Setup page.
2.Set each parameter for the Wireless Configuration.
Setting Description
SSID The SSID must be set to match the...")
Operating Instructions 34 2.3 Using Wireless LAN Wireless communication is possible by adjusting the settings of the wireless LAN to those for the router. Take a note of the settings and save them for reference. For more information about wireless setting, please refer to http://panasonic.co.jp/ pcc/products/en/netwkcam/technic/wireless/cam_set.html 1.Click [Wireless] on the Setup page. 2.Set each parameter for the Wireless Configuration. Setting Description SSID The SSID must be set to match the...
Page 35
![Page 35
Operating Instructions
[For assistance, please call: 1-800-272-7033] 35
3.Set each parameter for the Encryption.
Setting Description
Cipher Select encrypting or not encrypting.
To prevent unauthorized users from reading data, selecting
[WEP] is recommended.
WEP Selection Checked WEPKey is used as a standard WEPKey. Check
the same number as the router.
WEPKey1—4 Select one from [HEX, 10 characters 64 bit], [HEX, 26
characters 128 bit], [HEX, 32 characters 152...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-34.png "Page 35
Operating Instructions
[For assistance, please call: 1-800-272-7033] 35
3.Set each parameter for the Encryption.
Setting Description
Cipher Select encrypting or not encrypting.
To prevent unauthorized users from reading data, selecting
[WEP] is recommended.
WEP Selection Checked WEPKey is used as a standard WEPKey. Check
the same number as the router.
WEPKey1—4 Select one from [HEX, 10 characters 64 bit], [HEX, 26
characters 128 bit], [HEX, 32 characters 152...")
Operating Instructions [For assistance, please call: 1-800-272-7033] 35 3.Set each parameter for the Encryption. Setting Description Cipher Select encrypting or not encrypting. To prevent unauthorized users from reading data, selecting [WEP] is recommended. WEP Selection Checked WEPKey is used as a standard WEPKey. Check the same number as the router. WEPKey1—4 Select one from [HEX, 10 characters 64 bit], [HEX, 26 characters 128 bit], [HEX, 32 characters 152...
Page 36
![Page 36
Operating Instructions
36
Notes
Some wireless devices do not support the WEP 152 bit.
The camera supports only the open system authentication. If the router or
access point is set to shared key authentication, set it to auto or open
system.
4.Click [Save] when finished.
New settings are saved.
When finished, Success! is displayed.
5.Click [Go to Wireless configuration page].
The Wireless page is displayed.
6.Set the switch to WIRELESS.
Notes
It takes about 1 minute for the new settings to...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-35.png "Page 36
Operating Instructions
36
Notes
Some wireless devices do not support the WEP 152 bit.
The camera supports only the open system authentication. If the router or
access point is set to shared key authentication, set it to auto or open
system.
4.Click [Save] when finished.
New settings are saved.
When finished, Success! is displayed.
5.Click [Go to Wireless configuration page].
The Wireless page is displayed.
6.Set the switch to WIRELESS.
Notes
It takes about 1 minute for the new settings to...")
Operating Instructions 36 Notes Some wireless devices do not support the WEP 152 bit. The camera supports only the open system authentication. If the router or access point is set to shared key authentication, set it to auto or open system. 4.Click [Save] when finished. New settings are saved. When finished, Success! is displayed. 5.Click [Go to Wireless configuration page]. The Wireless page is displayed. 6.Set the switch to WIRELESS. Notes It takes about 1 minute for the new settings to...
Page 37
![Page 37
Operating Instructions
[For assistance, please call: 1-800-272-7033] 37
2.4 Using UPnP (Universal Plug and Play)
UPnP can automatically configure your router to be accessed from the Internet. In
order to use this feature, your router needs to support this feature and it must be
enabled. Most router manufacturers disable this feature as the default setting. See
http://panasonic.co.jp/pcc/products/en/netwkcam/technic/rtr_setup for
details and see your router manual for...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-36.png "Page 37
Operating Instructions
[For assistance, please call: 1-800-272-7033] 37
2.4 Using UPnP (Universal Plug and Play)
UPnP can automatically configure your router to be accessed from the Internet. In
order to use this feature, your router needs to support this feature and it must be
enabled. Most router manufacturers disable this feature as the default setting. See
http://panasonic.co.jp/pcc/products/en/netwkcam/technic/rtr_setup for
details and see your router manual for...")
Operating Instructions [For assistance, please call: 1-800-272-7033] 37 2.4 Using UPnP (Universal Plug and Play) UPnP can automatically configure your router to be accessed from the Internet. In order to use this feature, your router needs to support this feature and it must be enabled. Most router manufacturers disable this feature as the default setting. See http://panasonic.co.jp/pcc/products/en/netwkcam/technic/rtr_setup for details and see your router manual for...
Page 38
Operating Instructions 38 2.5 Registering with the Viewnetcam.com service Viewnetcam.com is a free service (dynamic DNS service) that allows you to assign an easy to remember name to the camera, similar to your favorite web site. Viewnetcam.com also allows you to easily access the camera, even when your ISP changes the IP address. Panasonic Communications recommends you to register with it for the Internet access to the camera. See http://www.viewnetcam.com for details about the Viewnetcam.com...
Page 39
![Page 39
Operating Instructions
[For assistance, please call: 1-800-272-7033] 39
Notes
When the Viewnetcam.com registration website is not displayed, confirm
that the URL is displayed in the right column of the Your Account Link. If
the URL is not displayed, follow the procedures below.
Personal (Camera) URL is available after you registered with the
Viewnetcam.com service.
If port forwarding is not enabled or your network is not connected to the
Internet, the...](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-38.png "Page 39
Operating Instructions
[For assistance, please call: 1-800-272-7033] 39
Notes
When the Viewnetcam.com registration website is not displayed, confirm
that the URL is displayed in the right column of the Your Account Link. If
the URL is not displayed, follow the procedures below.
Personal (Camera) URL is available after you registered with the
Viewnetcam.com service.
If port forwarding is not enabled or your network is not connected to the
Internet, the...")
Operating Instructions [For assistance, please call: 1-800-272-7033] 39 Notes When the Viewnetcam.com registration website is not displayed, confirm that the URL is displayed in the right column of the Your Account Link. If the URL is not displayed, follow the procedures below. Personal (Camera) URL is available after you registered with the Viewnetcam.com service. If port forwarding is not enabled or your network is not connected to the Internet, the...
Page 40
![Page 40
Operating Instructions
40
2.6 Setting Date and Time
The Date and Time page allows you to set date and time. Date and time are used
for image buffer/transfer, operation time and time stamps on the buffered image.
Note
Saving the date and time settings deletes all buffered images.
1.Click [Date and Time] on the Setup page.
2.Set each parameter.
Clicking [Cancel] cancels your settings without saving changes.](http://img.usermanuals.tech/thumb/58/69511/w300_bl-c30a_en_om_d-39.png "Page 40
Operating Instructions
40
2.6 Setting Date and Time
The Date and Time page allows you to set date and time. Date and time are used
for image buffer/transfer, operation time and time stamps on the buffered image.
Note
Saving the date and time settings deletes all buffered images.
1.Click [Date and Time] on the Setup page.
2.Set each parameter.
Clicking [Cancel] cancels your settings without saving changes.")
Operating Instructions 40 2.6 Setting Date and Time The Date and Time page allows you to set date and time. Date and time are used for image buffer/transfer, operation time and time stamps on the buffered image. Note Saving the date and time settings deletes all buffered images. 1.Click [Date and Time] on the Setup page. 2.Set each parameter. Clicking [Cancel] cancels your settings without saving changes.