Panasonic Multi-Function Printer KX-MB2000 KX-MB2010 KX-MB2030 Operating Instructions

6Open the top cover ( H) by holding the indentations
( I ) on both sides of the unit.
Note:
R Do not touch the transfer roller ( J).
R If the lower glass ( K) is dirty, clean it with a soft
and dry cloth.
7 Install the drum and toner cartridge ( L) by holding
the tabs.
R Make sure that the arrows ( M) match, to install
the drum and toner cartridge correctly.
For assistance, please visit http://www.panasonic.com/help111. Introduction and InstallationHJ
I
I K L M  

8Close the top cover by holding the indentations on
both sides of the unit, until locked.
Caution:
R To prevent injuries, be careful not to put your
hands under the top cover.
When to replace the toner cartridge and the drum
cartridge
When the display shows the following, replace the toner
cartridge.
– “TONER LOW ”
– “TONER EMPTY ”
Note:
R To check the drum life and quality, please print the
printer test list (page 96) and refer to page 98 for
information on the drum life. If printing quality is still...

1.6 Output tray
Insert the output tray extender ( A) until it clicks into
place, and then press the center part ( B) of the extender
to open it.
Note:
R Do not place the unit in an area where the output tray
may be easily bumped into.
R The output tray can hold up to approximately 100
sheets of printed paper (the number of sheets may
vary depending on the usage environment). Remove
the printed paper before the output tray becomes full.
If the top part of the extender is detached
1. With the top part of...

1.7 Recording paper
The paper input tray unit can hold:
– Up to 250 sheets of 60 g/m 2
 to 75 g/m 2
 (16 lb to
20 lb) paper.
– Up to 230 sheets of 80 g/m 2
 (21 lb) paper.
– Up to 200 sheets of 90 g/m 2
 (24 lb) paper.
R A4, letter, B5 and 16K-size paper can be used. B5
and 16K-size paper can only be used when using the
unit for printing or copying.
R Please refer to page 97 for information on recording
paper.
R The unit is set for printing letter-size plain paper
by default.
– To use other paper sizes,...

4Adjust the recording paper guides. Pinch the front
side of the recording paper guide ( D), then slide it to
match the paper size mark. Pinch the right side of the
recording paper guide ( E), then slide it to adjust the
width to the size of the recording paper.
R Make sure that the recording paper is under the
paper limit mark ( F), and the paper should not
be loaded over the snubbers ( G).
5 Insert the paper input tray into the unit, lifting the front
part of the tray. Then push it completely into the...

2Insert the paper, print-side down ( B) until the unit
grasps the paper and a single beep is heard.
Note:
R To print from the manual input tray;
– when printing with the computer, select #2 for the
printer properties.
– when making a copy, set the copy input tray setting to  “#2 ” beforehand (feature #460 on
page 63).
If these settings are not changed, when printing or
copying multiple pages, the 1st page will be printed
from the manual input tray, but the rest of the pages
will be printed from the paper...

2.1 Connections
Caution:
R When you operate this product, the power outlet
should be near the product and easily accessible.
* The pictured model is KX-MB2030.
Power cord
R Connect to a power outlet
(120 V, 60 Hz).
Telephone line cord *1
R Connect to a single telephone line jack (RJ11C).
[EXT]  jack*1
R You can connect an answering machine or an
extension telephone. Remove the stopper if
attached.
Answering machine (not supplied) *1
To the Internet
Network router/Network hub (not supplied)
R Also connect...

2.2 Turning the power switch ON
Turn the power switch to the ON position ( A).2.3 Dialing mode (KX-MB2030
only)
If you cannot dial (page 41), change this setting
according to your telephone line service.
1 MMenu N
2 Press  MB NM1NM 2NM 0N to display  “DIALING MODE ”.
3 Press  M1 N or  M2 N to select the desired setting.
M 1 N “ PULSE ”: For rotary/pulse dial service.
M 2 N “ TONE ” (default): For tone dial service.
4 MSet N
5 Press  MMenu N to exit.
18For assistance, please visit...

2.4 Selecting the operation mode
(Scan/Copy) (Fax: KX-MB2030
only)
You can select the desired mode by pressing one of the
following buttons.
– MScan N: Select this mode when using the unit as a
scanner (page 30).
– MCopy N: Select this mode when using the unit as a
copier (page 34).
– MFax N (KX-MB2030 only): Select this mode when
using the unit as a fax machine (page 41).
Note:
R The default operation mode is the copy mode.
R You can change the default operation mode (feature
#463 on page 58) and the...

2.5.2 Using the automatic document feeder
(KX-MB2010/KX-MB2030 only)
* The pictured model is KX-MB2010.
1 Insert the document (up to 20 pages) FACE UP into
the feeder until a single beep is heard.
2 Adjust the width of the document guides ( A) to fit the
actual size of the document.
Note:
R Confirm that there are no documents on the scanner
glass.
R Confirm that any ink, paste or correction fluid has
dried completely.
R Remove clips, staples or other fasteners.
R Do not insert the following types of...