Panasonic Monitoring Software Digital Disk Recorder Wj Rt416 Operating Instructions

11
Configure the Network Settings
With the following network environment, it is not necessary to configure the network settings. It is possible to config-
ure the settings or operate the recorder using the monitoring software after completing the connection.
IP Address: 192.168.0.2 - 192.168.0.249, 192.168.0.251 - 192.168.0.254
Subnet Mask: 255.255.255.0
Gateway Address: 192.168.0.1
When the network settings are different from the settings above, configure the network settings of the recorder and
the...

12
Screenshot 2
The control panel will be displayed.
Step 2
Click the Network and Internet Connections icon.
Screenshot 3
The Network and Internet Connections window will be
displayed.
Step 3
Click Network Connections.
Screenshot 4
The Network Connections window will be displayed.
Step 4
Double click Local Area Connection. 

13
Screenshot 5
The Local Area Connection Status window will be dis-
played.
Step 5
Click Properties.
Screenshot 6
The Local Area Connection Properties window will be
displayed.
Step 6
Click Internet Protocol (TCP/IP), and then click
Properties.
Screenshot 7
The Properties window of Internet Protocol (TCP/IP)
will be displayed.
Step 7
Click Use the following IP address and enter the IP
address and the subnet mask as follows;
• IP Address: 192.168.0.9
• Subnet Mask: 255.255.255.0
Step 8
Click the OK...

14
Settings relating to the connection with the recorder
Before operating on the operation window, configure the network settings between the PC and the recorder.
Screenshot 1
Click the [Monitor System Setup] button.
The pop-up menu will be displayed.
Select Recorder Setup under Monitor System
Config.
The Recorder Setup window will be displayed.
Step 1
Click the [Insert] button in the Recorder Info. section,
and then register the recorder information.
The password is arbitrary.
Important:
Operable...

15
Monitor Live Images
Screenshot 3
The Connect window will be displayed.
Step 3
Select the recorder to access and the desired camera
channel.
Notes:
• Only the recorders registered in advance can be
selected on the Connect window. Refer to page 14
for further information.
• The password registered when registered the
recorder will be entered automatically.
• When displaying images from 5 or more camera
channels of the same recorder, or when displaying
recorded images in an area on a multi-screen, only...

16
Switch the image display area between a single screen and a multi-screen
Display images on a single screen in the image display area
Click the desired area selection button.
→The selected area will be displayed on a single screen in the image display area. The image display area will be
switched to a single screen by clicking one of the area selection buttons when a multi-screen is displayed in the
image display area.
The area selection buttons will change as follows to indicate the current status....

17
Screenshot 1
Start operation when the operation window is being dis-
played.
Step 1
Right-click on the displayed image that is from the cam-
era to be disconnected.
Screenshot 2
The pop-up menu will be displayed.
Step 2
Select Disconnect.
→The connection with the selected camera will be dis-
connected.
: The camera respective to this area is in the alarm status.
: Live images or recorded images currently being displayed are being saved. When this icon is blinking, images
are being recorded by the...

18
Login to the recorder
Log in the recorder as follows.
Screenshot 1
Click the [Login] button.
→The Login window will be displayed.
Important:
Depending of the firewall setting of Windows XP
SP2, recorder information may sometimes not be
displayed. Refer to page 6 for further information.
Step 1
Select the desired recorder and enter the password of
the user level Manager.
Note:
Only the recorders registered in advance can be
selected on the Login window. Refer to page 14 for
further information.
Step 2...

19
Play recorded images on the recorder
Recorded images can be played from the search result window. It is possible to search recorded images to be
played by designating multiple search filters (List Search) or by designating the start time and date of recording
(Time & Date Search).
To play recorded images, log in the recorder as Manager. Refer to page 18 for how to log in the recorder.
Important:
It is impossible to play recorded images which is currently being played or copied on the recorder.
Note:...

20
Screenshot 3
The List Search window will be displayed.
Step 3
Set the desired search filter.
Camera
Check the radio button of the desired camera channel to
be searched.Filtering
Off: Searches without filtering
Manual: Searches for only images recorded by the
manual recording
Timer: Searches for only images recorded by the
timer recording
Alarm: Searches for only images recorded by the
alarm recording (triggered by a terminal
input, VMD and a command alarm
reception)
Terminal: Searches for only images...