Panasonic Memory Card Camera Recorder Ajhpx2700 Operating Instructions

111Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
Preparation
1Raise the lens clamping lever and remove the mount 
cap.
a.Lens clamping lever
b.Mount cap
2To mount the lens, align the indentation at the top center 
of the lens mount with the center mark of the lens.
c.Mark
3Lower the lens clamping lever to clamp the lens.
4Secure the cable through the cable clamp, and plug it 
into the LENS connector.
d.LENS connector
5Adjust the lens flange back.

11 2Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
8Repeat steps 5 to 7 until the lens is in focus at both the 
telephoto and wide-angle positions.
9Firmly tighten the F.f ring clamping screw.
Method to correct the waveform to be more flat by 
combining the sawtooth-shaped waveform and the 
parabola waveform when watching the respective 
waveforms of R, G and B of the video signals.

11 3Preparation: Mounting the lens and Performing the Flange Back and White Shading Adjustments
Preparation
When making the white shading correction, make the 
adjustment while observing the R, G, and B waveforms in 
the horizontal and vertical directions with the waveform 
monitor.
This now completes the white shading adjustments.
The adjustment values are now stored in the non-volatile 
memory so that even when the unit’s power is turned off, 
there will be no further need to perform the white shading...

11 4Preparation: Preparing for Audio Input Take the following steps to prepare the camera for connecting audio input devices.
The unit can be equipped with the AJ-MC900G stereo 
microphone kit (optional).
1Open the microphone holder.
2Mount the microphone and tighten the clamping screw. 
The microphone must be attached with the UP mark on 
the microphone facing up.
a.Clamping screw
3Connect the microphone cable to the MIC IN jack on the 
camera.
b.MIC IN jack
4Set the AUDIO IN switch to [FRONT] depending...

11 5Preparation: Mounting the Camera on a Tripod
Preparation
1Connect the audio device to the AUDIO IN jack with the 
XLR cable.
2Set the AUDIO IN switch to [REAR] for the channel to 
which the XLR cable is connected.
3Set the LINE/MIC/+48V selector switch on the rear 
panel to [LINE].
a.LINE/MIC/+48V selector switch
b.AUDIO IN switch
c.AUDIO IN jack
When mounting the camera on a tripod, use the tripod adapter supplied with the camera.
1Mount the tripod adapter on the tripod.
a.Tripod adapter
b.Pan head

11 6Preparation: Attaching the Shoulder Strap To detach the shoulder strap, first open the hooks, then 
detach the strap.

11 7Preparation: Connection of the remote control unit (AJ-RC10G)
Preparation
It is possible to control some of the functions remotely by 
connecting the remote control unit AJ-RC10G (optional).
When AJ-RC10G is connected to the REMOTE connector 
on the unit and the power switches of both of the unit and 
AJ-RC10G are turned on, the unit automatically enters the 
remote control mode.
The remote control mode is released when AJ-RC10G is 
removed or the power for the AJ-RC10G is turned off.
In the remote...

11 8Preparation: Attaching the Front Audio Level Control Knob CHARA ON button
This button is used to select whether to superimpose 
characters on the video signal output to the MON OUT 
connector of this unit. Note that the MON OUT 
CHARACTER switch of this unit does not function when 
the AJ-RC10G is connected.
Scene file
Scene files created on other types of device cannot be 
read. When an attempt is made to read such a file, AJ-
RC10G displays “NG” on the liquid crystal screen.
Menu option
GAMMA menu...

11 9Preparation: Connection of the external switch
Preparation
It is possible to draw 1.5 A current from the DC OUT 
connector of the unit.
Recording start/stop can be controlled by connecting an 
external switch to this connector.
Since a tally lamp can be used by connecting an LED to this 
connector, it is useful for shooting video when fixing the 
camera on a crane.
Connection of the external switch
1: GND
2: TALLY OUT
Open collector output on the unit side.
TA L LY  O N :
TALLY OFF:Low impedance
High...

120Manipulating Clips with Thumbnails: Thumbnail Manipulations Overview
Manipulating Clips with Thumbnails
A clip is a data group that includes the images and sounds 
created from one shooting session, together with additional 
information such as text memos and meta data.
The following manipulations can be performed using the 
cursor and SET buttons, while checking the images 
displayed on the LCD monitor:yPlayback, delete, copy or restore the clip.
yAdd or delete a shot mark and a text memo on the clip...