Panasonic Memory Card Camera Recorder Ajhpx2700 Operating Instructions

81Adjustments and Settings for Recording: Viewfinder Screen Status Displays
Adjustments and Settings for Recording
Information Item Indication Status
26. Iris, F valueNC
OPEN
F1.7 - F16
CLOSELens cable is not connected.
Lens iris is at maximum.
Lens iris value
Lens iris closed.

82Adjustments and Settings for Recording: Viewfinder Screen Status Displays
*1 The menu option P2CARD REMAIN can be found in the  screen on the VF page.
*2 If the remaining free space or memory capacity is 9999 min or more, [9999min] is displayed.Information Item Indication Status
36. B.GAMMA 
RANGE1
2
3This indicates the level (upper limit) of the compression/expansion.
37. Switch lock 
setting!SW LOCK This is displayed when any of the side switches (GAIN, OUTPUT and AWB 
switches) are operated with...

83Adjustments and Settings for Recording: Viewfinder Screen Status Displays
Adjustments and Settings for Recording
*{: Not provided when the menu option STATUS is set to “OFF”, which can be found in the  screen on the VF page.
z: Provided regardless of the menu option setting.
Indications Available in the Viewfinder Screen
Selectable 
between on and 
off through menu 
optionsProvided when 
the appropriate 
status is 
encountered.Provided during 
MODE CHECK*Can be switched 
off.Provided during 
playback...

84Adjustments and Settings for Recording: Viewfinder Screen Status Displays The messages that appear on the viewfinder screen to 
indicate changes to settings and adjustment results may be 
limited, or set not to appear, through the menu option DISP 
MODE. This menu option can be found in the  screen on the VF page.
For directions on navigating the menu, see [Setting Menu 
Options] (page 163).
The center, safety zone, safety zone area and frame 
markers may be set to on or off, along with specifications...

85Adjustments and Settings for Recording: Viewfinder Screen Status Displays
Adjustments and Settings for Recording
The viewfinder can display a screen that allows you to view 
the marker settings of the unit.
Pressing the MARKER SELECT button on the unit switches 
the marker indication as follows.
Marker A  Marker B  No marker
If the menu option FRAME SIG is set to “16:9” as the 
information of Marker A and “4:3” as the information of 
Marker B, then the 16:9 and 4:3 view angles can easily be 
checked...

86Adjustments and Settings for Recording: Adjusting and setting the LCD monitor
1Turn on the POWER switch of the unit.
2Slide the OPEN button in the arrow 1 direction to open 
the LCD monitor in the arrow 2 direction.
3Adjust the angle of the LCD monitor for most convenient 
viewing.
The monitor can turn up to 180 degrees towards the 
lens and up to 90 degrees towards you.

87Adjustments and Settings for Recording: Selection of video output signals
Adjustments and Settings for Recording
The unit employs the HD SDI A · B connector and the MON OUT connector as connectors for outputting video signals.
Change the characters of the signal output from the HD SDI 
A · B connector using the  screen from the 
menu. The character content output from the HD SDI A · B 
connector and MON OUT is the same.
The signals output from the HD SDI A · B connector are 
switched with the HD SDI A...

88Adjustments and Settings for Recording: Selection of video output signals The MON OUT connector outputs HD SDI signals or down-
converted analog signals.
Set the video signals output from the MON OUT connector 
by using the MONITOR OUT item on the menu ( screen on the SYSTEM SETTING page).
The signals output from the MON OUT connector are 
switched with the OUTPUT SEL switch.
However, the switching operation is not acknowledged 
during the recording operation.
MEM:During EE, such as recording, video...

89Adjustments and Settings for Recording: Handling data
Adjustments and Settings for Recording
The unit employs 5 sets for the file data area.
FACTORY data:
The area for storing factory settings
Data cannot be revised with menu operations.
USER data:
The area for storing the data set by menu operations
The FACTORY data is stored as the factory setting.
CURRENT data:
The area for storing the operating status of the unit
The set value in this area is revised by menu operations.
SCENE file:
16 sets of scene...

90Adjustments and Settings for Recording: Handling data An SD memory card may be inserted or removed, either before or after the power is turned on.
Open the lid of the switch cover, and insert an SD memory 
card (optional) into the SD memory card slot with the notch 
upward. Close the lid.