Panasonic Memory Card Camera Recorder Ajhpx2700 Operating Instructions

151Maintenance and Inspections: Maintenance
Maintenance and Inspections

152Maintenance and Inspections: Maintenance REMOTE
Panasonic part number K1AY110JA001
1 CAM DATA (H) Data from the camera to the remote control (H)Maker part number HR10A-10R-10SC(71)
(Hirose Denki)
2 CAM DATA (C) Data from the camera to the remote control (C)
3 CAM CONT (H) Control signals from the remote control to the camera (H)
4 CAM CONT (C) Control signals from the remote control to the camera (C)
Connector at the cable side
5
RC-ONIdentification signals of the remote control
Low: ONMaker part...

153Maintenance and Inspections: Maintenance
Maintenance and Inspections
LENSPanasonic part number K1AY112JA001
1 RET-SW On/off of the return video
RETURN ON: GND
RETURN OFF: OPENMaker part number HR10A-10R-12SC(71)
(Hirose Denki)
2REC-START/
STOPControl for recording start/stop
3GND GND
4 IRIS-AUTO On/off of the forced iris servo
SERVO ON: +5 V±0.5 V
SERVO OFF: OPEN
5 IRIS-CONT Control output for the lens iris
F2.8: –6.2 V, F16: +3.4 V, CLOSE: +2.5 V
6 UNREG-12 V +12 V power supply for the lens (Max. 1.5...

154Maintenance and Inspections: Maintenance Unislot Interface
Panasonic part number K1GB25A00010
1 CH-1 SHIELD GNDMaker part number HDBB-25S(05)
(Hirose Denki)
2 CH-1 HOT Audio input from the wireless receiver: CH1 HOT
3 CH-1 COLD Audio input from the wireless receiver: CH1 COLD
4GND GND
5 +12 V UNREG Power supply to the wireless receiver
6 RX ON Power supply remote output to the wireless receiver
7 RF WARN RF warning input from the wireless receiver
8 RM5 Not used
9 RM4 Not used
10 SPARE 1 Not used
11...

155Maintenance and Inspections: Warning System
Maintenance and Inspections
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING 
lamp, lamps inside the viewfinder and a warning tone.

156Maintenance and Inspections: Warning System 6. Recording Error
Display window 
indication“00:00:00:11” appears in the time code 
display field. Even after recording is 
stopped, this display continues to blink 
until the next operation is performed.
WARNING lampBlinks 4 times per second while recording 
continues.
Tally lampBlinks 4 times per second while recording 
continues.
ViewfinderThe “REC WARNING” indicator lights up.
Warning toneBeeps 4 times per second while recording 
continues.
Warning...

157Maintenance and Inspections: Warning System
Maintenance and Inspections
11. P2 Card Error
Display window 
indicationIf the error occurs during recording, 
“00:00:00:11” appears in the time code 
display field. The indication continues to 
flash after recording is stopped and until 
the next operation is performed. There is 
no indication if the error occurs during 
playback.
WARNING lampIf the error occurs during recording, the 
lamp flashes 4 times per second for a 
period of about 3 seconds after...

158Maintenance and Inspections: Warning System The following error codes are displayed in the display window if an error occurs in the camera:
Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 155) for countermeasures.
Error Codes
Code No. Description Type of warnings
E-11 Video initialization error 1. System Errors
E-27 Recording control error 1. System Errors
E-30 P2 card removal error 2. Card removal error
E-34 LCD microcontroller error 1. System Errors...

159Maintenance and Inspections: Warning System
Maintenance and Inspections
Warning and Error Display for Thumbnail Operation and USB HOST MODE
ItemMessageDescriptionMeasure
ThumbnailsCANNOT ACCESS! Data cannot be accessed because it is corrupted 
or for other reasons.Restore media and clips to normal state before 
access.
WRITE 
PROTECTED!The P2 or SD card is write protected. Insert write-enabled media.
CARD FULL! The P2 or SD card is full. Insert media with sufficient capacity.
NO CARD! No P2 or SD card...

160Maintenance and Inspections: Warning System
HDD
(USB HOST 
mode)HDD CAPACITY 
FULL!Not enough space left on the hard disk. There is not enough space on the connected 
hard disk. Use a new hard disk or formatted hard 
disk.
TOO MANY 
PA R T I T I O N S !There are too many partitions. Hard disks can handle up to 23 partitions. Use a 
new hard disk or formatted hard disk.
HDD 
DISCONNECTED!The unit is not connected to a hard disk. Reconnect the USB cable. If the hard disk does 
not operate normally, turn...