Panasonic Memory Card Camera Recorder Ajhpx2000 Operating Instructions

101PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
 Preparation
1Raise the lens clamping lever and remove the mount 
cap. 
2To mount the lens, align the indentation at the top 
center of the lens mount with the center mark of the 
lens. 
3Lower the lens clamping lever to clamp the lens. 
4Secure the cable through the cable clamp, and plug it 
into the LENS connector. 
5Adjust the lens flange back. 
‹Notes
zPlease refer to the lens instruction manual for...

102PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
8Repeat Steps 5 to 7 until the lens is in focus at both 
the telephoto and wide-angle positions. 
9Firmly tighten the F.f ring clamping screw. 
Method to correct the waveform to be more flat by 
combining the sawtooth-shaped waveform and the 
parabola waveform when watching the respective 
waveforms of R, G and B of the video signals.
White shading adjustment is disabled when the DS. GAIN
is turned ON or the...

103PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
 Preparation
When making the white shading correction, make the
adjustment while observing the R, G, and B waveforms in
the horizontal and vertical directions with the waveform
monitor.
This now completes the white shading adjustments.
The adjustment values are now stored in the non-volatile
memory so that even when the unit’s power is turned off,
there will be no further need to perform the white shading...

104PreparationPreparing for Audio Input
Take the following steps to prepare the camera for connecting audio input devices. 
AJ-HPX2000 can be equipped with the AJ-MC900G stereo
microphone kit (an extra-cost option).
1Open the microphone holder. 
2Mount the microphone and tighten the clamping 
screw. The microphone must be attached with the UP 
mark on the microphone facing up.
3Connect the microphone cable to the MIC IN jack on 
the camera. 
4Set the AUDIO IN switch to [FRONT] depending on 
the audio...

105PreparationMounting the Camera on a Tripod
 Preparation
1Connect the audio device to the AUDIO IN jack with 
the XLR cable. 
2Set the AUDIO IN switch to [REAR] for the channel to 
which the XLR cable is connected. 
3Set the LINE/MIC/+48V selector switch on the rear 
panel to [LINE]. 
When mounting the camera on a tripod, use the tripod adapter supplied with the camera. 
1Mount the tripod adapter on the tripod. 
‹Note
Select an appropriate hole in the adapter, taking into 
account the center of...

106PreparationAttaching the Shoulder Strap
To detach the shoulder strap, first open the hooks, then
detach the strap. 
‹Note
Make sure that the shoulder strap is securely attached. 
Attaching the Shoulder Strap
Shoulder Strap 
Press to 
open the 
Attaching the Rain Cover
When using the SHAN-RC700 Rain Cover
Secure with the surface fastener
Tighten the cord 
Secure with the 
surface fastener
AJ-HPX2000P(VQT1D27-1)E.book  106 ページ  ２００７年７月３０日　月曜日　午後１時３１分 

107PreparationConnection of the remote control unit (AJ-RC10G)
 Preparation
It is possible to control some of the functions remotely by
connecting the remote control unit AJ-RC10G (optional
accessory).
When AJ-RC10G is connected to the REMOTE connector
on the unit and the power switches of both of the unit and
AJ-RC10G are turned on, the unit automatically enters the
remote control mode.
The remote control mode is released when AJ-RC10G is
removed or the power for the AJ-RC10G is turned OFF.
In the...

108PreparationConnection of the external switch
It is possible to draw 1.5 A current from the DC OUT
connector of the unit.
REC start/stop can be controlled by connecting an external
switch to this connector.
Since a tally lamp can be used by connecting an LED to
this connector, it is useful for shooting video when fixing
the camera on a crane.
1: GND
2: TALLY OUT
Open collector output on the unit side
TA L LY  O N
Low impedance
TA L LY  O F FHigh impedance
3: REC start/stop switch
This is...

109Manipulating Clips with Thumbnails : Thumbnail Manipulations Overview
 Manipulating Clips with Thumbnails
A clip is a data group that includes the images and voices
created from one shooting session, together with
additional information such as text memos and meta data. 
The following manipulations can be performed using the
cursor and SET buttons, while checking the images
displayed on the LCD monitor: zPlayback, delete, copy or restore the clip.
zAdd or delete a shot mark and a text memo on the...

110Manipulating Clips with Thumbnails : Thumbnail Screen Press the THUMBNAIL button to display the thumbnail
screen on the LCD monitor. Pressing the THUMBNAIL
button again returns the display to the regular display.
When switching is done from the regular screen display to
the thumbnail screen display, all the clips will be displayed
on the thumbnail screen.
Pressing the MENU button allows you to navigate the
thumbnail menu.
‹Note
With the TCG switch positioned at [SET], when the time
code or user bits...