Panasonic Memory Card Camera Recorder Ajhpx2000 Operating Instructions

81Adjustments and Settings for Recording : Selection of video output signals
 Adjustments and Settings for Recording
The unit employs the VIDEO OUT connector and the MON OUT connector as connectors for outputting video signals.
The signal modes for outputting signals from the VIDEO
OUT connector are switched with the VIDEO OUT switch.
HD SDI:
To output the HD SDI signals. When the camera-
recorder is set to the SD mode, SD-SDI signals are
output.
SD SDI:
To output the SD SDI signals. (Signals are down-...

82Adjustments and Settings for Recording : Selection of video output signals
The MON OUT connector outputs down-converted analog
signals.
Set the video signals output from the MON OUT connector
by using the MONITOR OUT item on the menu ( screen on the SYSTEM SETTING page).
Set to superimpose characters to the VBS signals output
from the MON OUT connector in the MONITOR OUT
CHARA item of the menu ( screen on the
SYSTEM SETTING page).
Settings of signals output from MON OUT connector
ItemVa r i a b l e...

83Adjustments and Settings for Recording : Handling data
 Adjustments and Settings for Recording
The unit employs 5 sets for the file data area.
FAC TO RY  d a t a :
The area for storing factory settings
Data cannot be revised with menu operations.
USER data:
The area for storing the data set by menu operations
The FACTORY data is stored as the factory setting.
CURRENT data:
The area for storing the operating status of the unit
The set value in this area is revised by menu
operations.
SCENE file:
Four...

84Adjustments and Settings for Recording : Handling data
An SD memory card may be inserted or removed, either before or after the power is turned on.
Open the lid of the switch cover, and insert an SD memory
card (optional accessory) into the SD memory card slot
with the notch upward. Close the lid.
‹Note
An SD memory card must be inserted with the right side
facing the slot. If the card is hard to insert, it may be
reversed or upside down. Do not force it into the slot.
Check the card before...

85Adjustments and Settings for Recording : Handling data
 Adjustments and Settings for Recording
4To format the SD memory card, turn the JOG dial 
button to move the cursor to YES. Then, press the dial 
button.
When the SD memory card has been formatted, the 
following message appears:
The card will not be formatted if the following message
appears when the JOG dial button is pressed:
5To exit the menu, press the MENU button.
The settings menu disappears and the status of the 
unit is indicated at the...

86Adjustments and Settings for Recording : Handling data
6Turn the JOG dial button until a desired character 
appears. 
The characters that appear are switched in the 
following order:
Space:
†
Ð
Alphabetical characters: A to Z
Ð
Numerals: 0 to 9
Ð
Symbols: , >, 
 R.SELECT         :1
  READ
 W.SELECT         :1
  WRITE
 CARD CONFIG
 TITLE READ
      
; TITLE:
 1: ********  5: ********
 2: ********  6: ********
 3: ********  7: ********
 4: ********  8: ********
 WRITE?
  YES
#  NO
TITLE:
Error message...

87Adjustments and Settings for Recording : Handling data
 Adjustments and Settings for Recording
1Navigate the menu to the  
screen. 
2Turn the JOG dial button to move the cursor to the 
menu option [R. SELECT]. Then, press the dial 
button.
3Turn the JOG dial button to select a desired number 
(1 - 8). Then, press the dial button.
4Turn the JOG dial button to move the cursor to the 
option [READ].
5Press the JOG dial button to display the following 
message:
6Turn the JOG dial button to move the cursor...

88Adjustments and Settings for Recording : Handling data
It is possible to transfer settings and other data to the user
area of the internal memory of the unit.
This data allows you to quickly reproduce an optimum
setup state.
To write data, go to the  screen from the FILE
page. To read the written user data, go to the 
screen from the FILE page.
1Navigate the menu to the  screen. 
2Turn the JOG dial button to move the cursor to the 
option WRITE USER DATA.
3Press the JOG dial button to display the...

89Adjustments and Settings for Recording : Handling data
 Adjustments and Settings for Recording
It is possible to write the settings data into the scene file
area of the internal memory of the unit, or to read data
written in this area. Four types of scene files are available.
This data allows you to quickly reproduce an optimum
setup state.
To change the settings, go to the  screen from
the FILE page.
1Navigate the menu to the SCENE screen. 
2Turn the JOG dial button to move the cursor to the 
SCENE...

90Adjustments and Settings for Recording : Handling data
1Navigate the menu to the  screen. 
2Turn the JOG dial button to move the cursor to the 
option SCENE SEL.
3Press the JOG dial button to blink scene file numbers. 
Then, turn the dial button to select a desired scene 
file number.
4Press the JOG dial button to accept the scene file.
5Turn the JOG dial button to move the cursor to the 
READ option.
6Press the JOG dial button to display the following 
message:
7Turn the JOG dial button to move the...