Panasonic Memory Card Camera Recorder Ajhpx2000 Operating Instructions

141Maintenance and Inspections : Maintenance
 Maintenance and Inspections
‹Note
Ensure that the polarities are used correctly for a power
supply from an external source.
Connector Signals
DC IN
1GND
2NC
3NC
4 +12V
FRONT MIC IN
1GND
2 L CH IN (H)
3 L CH IN (C)
4 R CH IN (H)
5 R CH IN (C)
AUD I O I N
1GND
2 AUDIO IN(H)
3 AUDIO IN(C)
AUDIO OUT
1GND
2L CH OUT (H)
3L CH OUT (C)
4 R CH OUT (H)
5 R CH OUT (C)
12
34
Matsushita part number K1AA104H0038
Maker part number HA16RX-4P
¢SW1£
(Hirose Denki)
PUSH
1 5...

142Maintenance and Inspections : Maintenance REMOTE
1 CAM DATA (H) Data from the camera to the remote control (H)
2 CAM DATA (C) Data from the camera to the remote control (C)
3 CAM CONT (H) Control signals from the remote control to the camera (H)
4 CAM CONT (C) Control signals from the remote control to the camera (C)
5 RC-ON Identification signals of the remote control
Low: ON
6 RC VIDEO OUT Video signals output to the remote control
7 RC VIDEO GND GND of the video signals to the remote control
8 NC...

143Maintenance and Inspections : Maintenance
 Maintenance and Inspections
LENS
1 RET-SW ON/OFF of the return video
RETURN ON: GND
RETURN OFF: OPEN
2 REC-START/STOP Control for recording start/stop
3GND GND
4 IRIS-AUTO ON/OFF of the forced iris servo
SERVO ON: +5V±0.5V
SERVO OFF: OPEN
5 IRIS-CONT Control output for the lens iris
F2.8: –6.2 V, F16: +3.4 V, CLOSE: +2.5 V
6 UNREG-12V +12V power supply for the lens (Max. 1.5 A)
7 IRIS-POSI Iris position signals
3.4 V (F16) to +6.2 V (F2.8)
8 IRIS-G-MAX IRIS...

144Maintenance and Inspections : Maintenance Unislot Interface
1 CH-1 SHIELD GND
2 CH-1 HOT Audio input from the wireless receiver: HOT
3 CH-1 COLD Audio input from the wireless receiver: COLD
4GND GND
5 +12V UNREG Power supply to the wireless receiver
6 RX ON Power supply remote output to the wireless receiver
7 RF WARN RF warning input from the wireless receiver
8RM5 Not used
9RM4 Not used
10 SPARE 1 Not used
11 SPARE 2 Not used
12 EXT CLK Not used
13 CLK SHIELD Not used
14 CH-2 SHIELD Not used
15 CH-2...

145Maintenance and Inspections : Warning System
 Maintenance and Inspections
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the 
WARNING lamp, lamps inside the viewfinder and a warning tone. 
‹Note
The WARNING lamp has the highest priority, followed by the tally lamp, and then the warning tone. When multiple errors 
occur simultaneously a higher priority indication will be triggered. The [WIRELESS RF], however, may not be indicated,...

146Maintenance and Inspections : Warning System 5. P2 Card Fully Recorded
Display window 
indication All 7 bar indicators for remaining MEDIA 
capacity start blinking. 
WARNING lamp This lamp will illuminate continuously until an 
operation is made after recording.
Tally lampThis lamp will flash 4 times every second 
until an operation is made after recording.
ViewfinderThe END indicator blinks. 
Warning toneThis tone will sound continuously until an 
operation is made after recording.
Warning...

147Maintenance and Inspections : Warning System
 Maintenance and Inspections
9. 1394  Error
Display window 
indication The 1394 E-¢¢ indicator in the display 
window blinks. For more information, see  
[
1394 Error Codes] (page 148).
WARNING lamp Blinks 4 times per second while the 
WARNING lamp recording is continuing.
Tally lampBlinks 4 times per second while the TALLY 
LAMP recording is continuing.
ViewfinderIn the case of Error Code 92, “1394 INITIAL 
ERROR” indicator lights up (during pause 
and...

148Maintenance and Inspections : Warning System The following error codes are displayed in the display window if an error occurs in the camera: 
Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 145) for countermeasures.
Error Codes
Code No.  Description  Type of warnings
E-11 Video initialisation error 1. System Errors
E-27 Recording control error 1. System Errors
E-30 P2 card removal error 2. 
Card removal error
E-34 LCD microcontroller error 1. System...

149Maintenance and Inspections : Warning System
 Maintenance and Inspections
Card Warning Code
Code No.  Description  RecordingIndication in display 
window
E-70
The directory organization on the inserted P2 
card does not comply with the standards. ([DIR 
NG CARD (Slot No.)] is indicated on the 
viewfinder.)Although different kinds of recording 
operations will function, data may not be 
recorded properly. Use the unit to format the 
card immediately.A warning code blinks once 
every 2 seconds on the...

150Maintenance and Inspections : Warning System
Soft 
keyboard
CANNOT CHANGE! [PERSON] will be entered while the text 
memo is not available.Enter [TEXT] before entering [PERSON].
CANNOT SET!
I N VA L I D  VA L U E !The entered value is incorrect. Change the value.
HDD
¢USB HOST 
MODE
£
HDD CAPACITY 
FULL!Not enough space left on the hard disk.  There is not enough space on the connected hard 
disk. Use a new hard disk or formatted hard disk. 
TOO MANY 
PARTITIONS!There are too many partitions.  Hard...