Panasonic Kx-tvs75, Kx-tvs100, Kx-tvs200 Voice Processing System Installation Manual

INSTALLATION31
Section 2
INSTALLATION 

2.1 SAFETY PRECAUTIONS
32INSTALLATION
2.1 SAFETY PRECAUTIONS
Please read the following precautions before installing the VPS.
2.1.1 Installation
The VPS needs to be installed on the wall. Improper placement of the system may result in 
malfunction, noise, or discoloration. Avoid installing the VPS in the following places:
•
in direct sunlight; in hot, cold, or humid places
•
in new areas where there are thermal springs, etc. (where sulfuric gas may damage the 
equipment or contacts).
•
where shocks or...

2.1 SAFETY PRECAUTIONS
INSTALLATION
33
Table 7 Hard Disk Drive Usage Environment
Te m p e r a t u r e: 5° C - 40° C
Relative humidity: 10% - 50%
Shock: Under 5 G
Vibration: 5Hz - 22Hz : 0.0042cm {0.020inch} displacement; double 
 amplitude,
 1 octave per minute.
 23Hz - 350Hz : Under 0.5G
Magnetic Field: DC : 6gauss
 to 700KHz : 7milligauss
 700KHz - 1.5MHz : 3milligauss 

2.2 FRAME GROUND CONNECTION
34INSTALLATION
2.2 FRAME GROUND CONNECTION
IMPORTANT!!!
Connect the frame of the main unit to the ground.
1.Loosen the screw.
2.Insert the grounding wire.
3.Tighten the screw.
4.Connect the grounding wire to the ground.
In most of North America, the ground provided by the Third wire ground at the commercial 
power outlet will be satisfactory. However, in some cases this ground may be installed 
incorrectly. Therefore, the following test procedure should be performed.
Test...

2.2 FRAME GROUND CONNECTION
INSTALLATION
35
3.Move one of the meter probes to the third prong terminal (GND).
Either the same reading or a reading of 0 V should be obtained.
4.If a reading of 0 V at 1 terminal and a reading of 108 V AC-132 V AC at the other terminal 
is not obtained, the outlet is not properly grounded. This condition should be corrected by 
a qualified electrician (per article 250 of the National Electrical Code).
5.If a reading of 0 V at 1 terminal and a reading of 108 V AC-132 V AC at...

2.3 INSTALLATION STEPS
36INSTALLATION
2.3 INSTALLATION STEPS
The following is an overview of the standard installation process using DPT. When necessary, 
other sections in this manual have been referenced for more detailed descriptions or 
instructions.
1.Get a list of current users, their extension numbers, their departments, and the type of 
systems they use (mailbox, no mailbox, beeper, car phone...).
2.Assess your customers needs before setting up the system. You will save yourself time later 
by...

2.3 INSTALLATION STEPS
INSTALLATION
37
d)Connect the computer to the voice processor with a Null Modem Cable (See 2.7.2 
Connecting the RS-232C Cable).
e)Turn the rotary switch to position 5.
f)Turn the power on.
g)Wait until the warning appears on the screen.
h)Turn the rotary switch back to position 0. 
CAUTION
If the rotary switch is not returned to position 0 after initialization, all programming will 
be lost when the voice processor loses power!
6.Perform Quick Setup. (See Section 5 CUSTOMIZING THE...

2.4 INSTALLING PORT EXPANSION CARD - KX-TVS100/KX-TVS200
38INSTALLATION
2.4 INSTALLING PORT EXPANSION CARD - KX-
TVS100/KX-TVS200
2.4.1 General
KX-TVS100
The KX-TVS100 can handle up to 4 calls simultaneously when the following port card is 
installed.
• KX-TVS102 (2 Digital/Analog port expansion card)
One port card (KX-TVS102) is installed at the factory.
KX-TVS200
The KX-TVS200 can handle up to 12 calls simultaneously when the following port cards are 
installed.
• KX-TVS102 (2 Digital/Analog port...

2.4 INSTALLING PORT EXPANSION CARD - KX-TVS100/KX-TVS200
INSTALLATION
39
2.4.2 Installing the KX-TVS102 or KX-TVS204 Port Card
Note
The following five steps are for the KX-TVS200. Please refer to them for the KX-TVS100.
1.Remove the adhesive tape from the card.
2.(KX-TVS102 only) Loosen, remove and discard the screw under the tape with a 
screwdriver.
3.Loosen the screw on the grounding strap, then remove the strap from the unit.
TVS102TVS204
SLOT 1SLOT 2 SLOT 3 

2.4 INSTALLING PORT EXPANSION CARD - KX-TVS100/KX-TVS200
40INSTALLATION
4.Insert the optional port card into SLOT 1 using the guide rails. (for the KX-TVS100, insert 
the optional port card into SLOT 2.)
5.Press the left and right card latches firmly, then fix the grounding strap to the unit with a 
screwdriver.
SLOT 1SLOT 2 SLOT 3
Guide Rail TVS102
SLOT 3
SLOT 2
SLOT 1
Guide Rail TVS204
SLOT 3
SLOT 2
SLOT 1
Guide Rail TVS102