Panasonic Kx Th102 Operating Instructions Manual

							Using a Cellular Phone with this Unit
For assistance, please visit http://www.panasonic.com/phonehelp71
Switching a cellular call 
between a cellular phone and 
the base unit o
From a cellular phone to the base unit
If you answer a cellular call using a cellular 
phone, you can transfer it to the base unit.
1During a cellular call using your cellular 
phone, press {CELLULAR}.
2“Transfer to base” i {SET}
3Select the desired cellular phone. i 
{SET}
LIf you registered only one cellular 
phone, skip to step 4.
4Follow the instructions of your cellular 
phone, if required.
LYou may need to enter the PIN (page 
52).
From the base unit to a cellular phone
If you answer a cellular call using the base 
unit, you can transfer it to the cellular 
phone that the call came in.
1During a cellular call using the base 
unit, press {CELLULAR}.
2“Transfer to Cell” i {SET}
Conference calls
Conference call with a cellular 
call and land line call 
Yo
While you are talking on a cellular call, you 
can make or answer a 2nd call on the land 
line, and then combine the calls to 
establish a conference call.
1During a cellular call, press {HOLD} 2 
times.
2To answer a land line call, press 
{LINE1} or {LINE2}.
To make a land line call, press {LINE1} 
or {LINE2}, then dial the phone 
number.
3When the land line call is connected, 
press {CONF} to make a conference 
call.
LTo hang up only one line, press the 
desired line button or {CELL} for the 
party with which you want to continue 
talking.
LTo put both lines on hold, press 
{HOLD}. To talk only with the land 
line caller, press the desired line 
button. To talk only with the cellular 
caller, press {C}. To resume both 
lines, press {CONF}.
1During a cellular call, press {HOLD}.
2To answer a land line call, press 
{LINE1} or {LINE2}.
To make a land line call, press {LINE1} 
or {LINE2}, then dial the phone 
number.
3When the land line call is connected, 
press {CONF} to make a conference 
call.
Handset
Base unit
TH102-C.book  Page 71  Monday, March 13, 2006  2:41 PM 
						

							Using a Cellular Phone with this Unit
72For assistance, please visit http://www.panasonic.com/phonehelp
LTo hang up only one line, press the 
desired line button or {CELLULAR} 
for the party with which you want to 
continue talking.
LTo put both lines on hold, press 
{HOLD}. To talk with only land line 
caller, press the desired line button. 
To talk only with the cellular caller, 
press {CELLULAR}. To resume both 
lines, press {CONF}.
Conference call with a cellular 
call and an intercom call 
Yo
While you are talking on a cellular call, one 
more extension can join the conversation 
and establish a conference call.
1During a cellular call, press 
{INTERCOM}.
2To page the base unit, press {0}.
To page another handset, enter its 
extension number ({1} to {8}).
3When the paged party answers, press 
{CONF} to make a conference call.
LTo leave the conference, press 
{OFF}. The other 2 parties can 
continue the conversation.
1During a cellular call, press 
{INTERCOM}.
2To page a handset, enter its extension 
number ({1} to {8}).
To page all handsets, press {0}.
3When the paged party answers, press 
{CONF} to make a conference call.
LTo leave the conference, press {SP-
PHONE}. The other 2 parties can 
continue the conversation.
Note for handset and base unit:
LThe cellular call can be put on hold by 
pressing {HOLD}. Only the person who placed the call on hold can resume the 
full conference by pressing {CONF} on 
the handset or {CONF} on the base unit.
Handset
Base unit
TH102-C.book  Page 72  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
For assistance, please visit http://www.panasonic.com/phonehelp73
Connecting to your network
By connecting the base unit to your LAN, you can use this unit to:
– connect to the Internet (requires a high-speed Internet service subscription).
– connect to a computer on the same network.
Connecting to your LAN
Connect the base unit using LAN cable.
Note:
LRefer to the included “Installation Guide for MULTI TALK V Software” for connections.
LWhen connecting the MULTI TALK V devices to a local area network, you need to know 
the following limitations.
– While you are using a dial up network (DUN) to access the Internet, no other data 
communication can take place using the same computer (for example, file sharing, 
browsing the cordless camera, printing with KX-THA16, etc.).
– If you have high-speed Internet service (DSL or Cable), it is better to connect the 
base unit behind a router to utilize the networking features properly (for example, 
sharing Internet connection, browsing the cordless camera with a computer, printing 
with the KX-THA16, etc.).
Connecting the USB cable to the unit
By connecting the USB cable to the USB port, you can use this unit to:
– use MULTI TALK V USB Utility with your computer.
– access to the Internet with your computer.
LINE1/2 LINE2 LAN
LAN cable (Category 5 UTP cable)
See note below.
TH102-C.book  Page 73  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
74For assistance, please visit http://www.panasonic.com/phonehelp
System requirements for your computer
The following system requirements must be met in order to use the MULTI TALK V 
software.
Trademarks
LMicrosoft and Windows are either registered trademarks or trademarks of Microsoft 
Corporation in the United States and/or other countries.
LPentium is a trademark or registered trademark of Intel Corporation or its subsidiaries in 
the United States and/or other countries.
LScreen shots are reprinted with permission from Microsoft Corporation.
LAll other trademarks identified herein are the property of their respective owners.
ItemDescription
Operating SystemMicrosoft
® Windows® 98SE, Microsoft Windows Me, 
Microsoft Windows 2000, or Microsoft Windows XP
CPUFor Windows 98SE and Windows Me: Pentium
® 166 MHz 
or faster
For Windows 2000: Pentium 200 MHz or faster
For Windows XP: Pentium 300 MHz or faster
RAMFor Windows 98SE and Windows Me: 64 MB (128 MB or 
more recommended)
For Windows 2000 and Windows XP: 128 MB
HDD50 MB available disk space
Resolution800 x 600 or higher resolution display
OthersUSB interface: 1.1
Video adaptor with high color (16 bit) or higher
CD-ROM drive
10/100 Mbps network card installed (necessary for LAN 
interface users)
Browser: Internet Explorer 5.0 or later (necessary when 
monitoring the cordless camera)
TH102-C.book  Page 74  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
For assistance, please visit http://www.panasonic.com/phonehelp75
Wall mounting
Base unit
The base unit can be mounted on a wall phone plate.
1Tuck the telephone line cord inside the wall mounting adaptor.
2Insert the upper hooks (A), then the lower hooks (B) on the wall mounting adaptor into 
the holes on the base unit until it clicks into the place.
3Connect the telephone line cord. Mount the base unit by inserting the mounting pins 
into the round openings on the adaptor (for pin B, use round cut out at the bottom of 
the adaptor if you’re using the 4 inches phone plate), then sliding the base unit down 
to secure it.
Connect the AC adaptor to power outlet (page 13).
LThere are two common types of wall phone plates. The distance between A and B 
may vary depending on the size of the wall phone plate installed.
LRaise the antennas.
A
B
83 mm (31/4 inches)or
102 mm 
(4 inches)
 (120 V AC, 60 Hz)
102 mm
(4 
inches)
83 mm
(31/4 inches)
TH102-C.book  Page 75  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
76For assistance, please visit http://www.panasonic.com/phonehelp
Charger
The charger can be mounted on the wall.
Drive the screws (not included) into the 
wall using the wall template as a guide, 
then mount the charger securely on the 
screws.
Connect the AC adaptor to power outlet 
(page 16).
Note:
LMake sure the screws are securely 
fastened to the wall.Belt clip
You can hang the handset on your belt or 
pocket using the included belt clip.
To attach the belt clip
To remove the belt clip
 (120 V AC,
 60 Hz)
Screws25.2 mm 
(1 inch)
Wall mount template for the charger
25.2 mm 
(1 inch)
TH102-C.book  Page 76  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
For assistance, please visit http://www.panasonic.com/phonehelp77
Headset (Optional)
Setting up a Bluetooth wireless 
headset o
If your headset is Bluetooth wireless 
technology compatible to the home 
communication system, you can have a 
hands-free phone conversation by 
registering your headset to the base unit.
Important:
LThe following procedures must be 
performed using the base unit.
LThere can only be one active Bluetooth 
headset connection at a time.
Registering a headset
Important:
LFor more details, please visit: 
www.panasonic.com/MultiTalkV
1Your headset:
Enter the registration mode of your 
headset (each headset’s instructions 
vary).
2Base unit:
{MENU} i h i {SET}
3“Bluetooth” i {SET}
4“Headset” i {SET}
5“Registration” i {SET}
6Enter the PIN of your headset. (Refer to 
the operating instructions provided with 
your headset.) i {SET}Note:
LTo cancel a headset from the base unit, 
see “Deregistering another device” on 
page 54.
Selecting a headset
This setting determines which headset is 
active. Only 1 headset can be active at a 
time. When “No headset” is selected, the 
headset feature is turned off.
1{MENU} i h i {SET}
2“Bluetooth” i {SET}
3“Headset” i {SET}
4“Headset select” i {SET}
5Select the desired headset. i {SET} 
i {STOP}
Switching a call between headset and 
base unit speakerphone
To switch to the base unit speakerphone, 
press {SP-PHONE}. 
To return to the headset, press {STOP}.
Connecting the corded headset 
Y
Connecting a headset to the handset 
allows hands-free phone conversations. 
Please use only a Panasonic headset 
(page 6).
LHeadset shown is KX-TCA86.
Switching a call between headset and 
handset speakerphone
To switch to the handset speakerphone, 
press {s}. 
To return to the headset, press {C}.
TH102-C.book  Page 77  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
78For assistance, please visit http://www.panasonic.com/phonehelp
Error messages
If the unit detects a problem, one of the following messages is shown on the display.
Display messageCause & solution
BusyLThe called handset or base unit is in use.
LOther users are using the line(s). Wait until the line 
button light or the line status icon goes out.
LPrivacy mode is on for the call you tried to join (page 
44).
LThe handset or base unit you tried to copy phonebook 
items to is in use.
LThe handset you are calling is too far from the base unit.
Denied
Turn access on at 
device.LThe monitor feature is turned off on the destination 
handset or base unit and the room cannot be monitored 
(page 45).
Error!!LThe handset’s registration or deregistration has failed. 
Move the handset and the base unit away from the 
electrical appliances and try again.
LAnother handset or base unit user tried to send 
phonebook items to you but there was an error. Have 
the other user re-send the items to you (page 33, 35).
Error!!
8 handsets have 
already been 
registered.L8 handsets have already been registered to the base 
unit. The deregistered handset number is still retained 
in the base unit. To register an additional handset, 
erase the unnecessary handset number using the base 
unit (page 54).
---Incomplete---LThe destination unit’s phonebook memory is full. Erase 
unnecessary items from the destination unit’s 
phonebook (page 32, 35).
LThe destination unit is out of area.
LThe destination unit’s user may have pressed {C} or 
{s} on the handset or {SP-PHONE} on the base unit.
InvalidLThere is no handset registered to the base unit 
matching the extension number you entered.
LYou selected your own extension number.
Invalid.
Please register
to the base unitLThe handset is not registered to the base unit. Register 
the handset (page 54).
Memory fullLThere is no space in memory to record new songs. 
Erase unnecessary songs (page 48).
No items storedLYour phonebook or redial list is empty.
L“Customize ring” is empty.
TH102-C.book  Page 78  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
For assistance, please visit http://www.panasonic.com/phonehelp79
No link to base. 
Move closer to base 
and try again.LThe handset has lost communication with the base unit. 
Move closer to the base unit, and try again.
LConfirm that the base unit’s AC adaptor is plugged in.
LRaise the base unit antennas.
LThe handset’s registration may have been canceled. 
Re-register the handset (page 54).
LAfter registering a cellular phone to the base unit, the 
communication between the base unit and other units 
may be disconnected. You need to wait for a few 
minutes and try again.
Phonebook fullLThere is no space to store new items in the phonebook. 
Erase unnecessary items (page 32, 35).
System is busy. 
Please try again 
later.LThe resources available for wireless communication 
(making or answering calls with a handset, monitoring 
audio in the room, etc.) are limited. Therefore, 
depending on the combination of wireless features 
being conducted at the same time, your desired 
operation may not be possible. Wait for other users to 
finish and try again.
LAnother user is listening to messages. Try again later.
Title errorLThe title for the customized ring is not entered or the title 
you entered is already used for another customized 
ring. Enter the title for that customized ring only.
Display messageCause & solution
TH102-C.book  Page 79  Monday, March 13, 2006  2:41 PM 
						

							Useful Information
80For assistance, please visit http://www.panasonic.com/phonehelp
Troubleshooting
General use
Programmable settings
ProblemCause & solution
The unit does not work.LMake sure that the battery is installed correctly and fully 
charged (page 16).
LCheck the connections (page 13 – 15).
LUnplug the base unit’s AC adaptor to reset the unit. 
Reconnect the adaptor and try again.
LThe handset has not been registered to the base unit. 
Register the handset (page 54).
I cannot hear a dial tone.LConfirm that the telephone line cord is connected (page 
14).
LDisconnect the base unit from the telephone line and 
connect a known working telephone. If the working 
telephone operates properly, contact our service 
personnel to have the unit repaired. If the working 
telephone does not operate properly, contact your 
telephone company.
“Recharge battery” is 
displayed and I cannot 
perform the following 
operations:
– recording or erasing a 
customized ringer
– editing a title for a 
customized ringer
– copying MULTI TALK V 
USB Utility settings 
(songs, phonebook 
items, programmable 
settings, etc.) from your 
computerLThe battery power is low. Fully charge the battery (page 
16) and try again.
ProblemCause & solution
I cannot program items.LWhile another user is listening to messages or the 
answering system is answering a call, you cannot 
program. Try again later.
While programming, the 
handset starts to ring.LA call is being received. Answer the call and start again 
after hanging up.
TH102-C.book  Page 80  Monday, March 13, 2006  2:41 PM