Panasonic Kx Tgf350 Operating Instructions Manual

Sub-menu 1Sub-menu 2SettingsCodeUnit
Set tel line*1Set dial modePulse
<
Tone >#120/13
Set flash time *12900 ms
<
700 ms >
600 ms
400 ms
300 ms
250 ms
200 ms
160 ms
110 ms
100 ms
90 ms
80 ms#121/15
Set line mode *13A
<
B >#122/–
Call sharing *1–<
On >
Off#194/16
RegistrationRegister handset–#13036
Deregistration *2–#13136
Deregistration*2––#13136
Battery saving
mode–On
<
Off >#15010
Change languageDisplay
Español#110/12
Voice prompt *1<
English >
Español#112/13
Main menu:  “ Customer support ”...

*1 If you program these settings using one of the units, you do not need to program the same item usinganother unit.
*2 This menu is not displayed when scrolling through the display menus. It is only available in direct command code.
*3 This feature allows the unit to automatically adjust the date and time each time caller information including date and time is received.
To turn this feature on, select  “Caller ID auto ”. To turn this feature off, select  “Manual ”. (Caller
ID subscribers only)
To use...

8Mb N: Select the desired alarm tone.  a
M SELECT N
R We recommend selecting a different ringer
tone from the one used for outside calls.
9 Mb N: Select the desired snooze setting.  a
M SAVE N
10 MSELECT N a  M OFF N
Note:
R Press  MSTOP N to stop the alarm completely.
R When the handset is in use, the alarm will not
sound until the handset is in standby mode.
R Press any dial key or  MSNOOZE N to stop the
sound but keep the snooze function activated.
R If you want to make an outside call when the...

test its sensitivity. Check the connection if you
are diverting the baby monitor to an outside line.
R This feature should not be used as a substitute
for a medical or caregiver’s supervision. It is the
caregiver’s responsibility to stay close enough
to handle any eventuality.
Note:
R If the unit is connected to a PBX system, you
cannot set the baby monitor.
R During the monitoring mode, battery
consumption is faster than usual. We
recommend leaving the monitored handset on
charger.
R The monitored...

5MMENU N a  M b N:  “Edit ” a  M SELECT N
6 Edit the name if necessary.  a M OK N
7 Edit the phone number if necessary.  a M OK N
a  M SELECT N
Erasing an outside monitoring number
Handset
1 Press  MMENU N on the handset being
monitored.
2 Mb N:  “On/Off ” a  M SELECT N
3 Mb N:  “On ” a  M SELECT N
4 Mb N: Select the outside line.  a M EDIT N
5 MMENU N a  M b N:  “Erase ” a  M SELECT N
6 Mb N:  “Yes ” a  M SELECT N a  M OFF N
Baby monitor sensitivity
You can adjust the sensitivity of the baby monitor....

Registering a unit
Operating additional units
Additional handsetsUp to 6 handsets can be registered to the base
unit.
Important:
R See page 4 for information on the available
model.
Registering  a  handset  to  the  base  unit
The supplied handset and base unit are
pre-registered. If for some reason the handset is
not registered to the base unit, re-register the
handset.
1 Handset:
MMENU N#130
2 Base unit:
Press and hold  MLOCATOR N for about 5
seconds.
R If all registered handsets start ringing, press...

Using Caller ID serviceImportant:
R This unit is Caller ID compatible. To use Caller
ID features, you must subscribe to a Caller ID
service. Contact your phone service provider for
details.
Caller ID features
Handset / Base unit
When an outside call is being received, the caller
information is displayed.
Caller information for the last 50 callers is logged
in the caller list from the most recent call to the
oldest.
R If the unit cannot receive caller information, the
following is displayed:
–“Out of...

Note for handset and base unit:
RIf the entry has already been viewed or
answered, “
” is displayed.
R In step 1, you can also access the caller list as
follows:
Base unit:
MCALL LOG N a  M b N:  “Incoming call ” a
M SELECT N
Editing a caller’s phone number
You can edit a phone number in the caller list by
removing its area code and/or the long distance
code “1”.
Handset
1 MC N CID
2 Mb N: Select the desired entry.  a M MENU N
3 Mb N:  “Edit ” a  M SELECT N
4 Press  MEDIT N repeatedly until the phone...

Answering system
The answering system can answer and record
calls for you when you are unavailable to answer
the phone.
You can also set the unit to play a greeting
message but not to record caller messages by
selecting “Greeting only ” as the recording
time setting (page 45).
Important:
R Make sure the unit’s date and time setting is
correct (page 13).
Memory capacity (including your
greeting message)
The total recording capacity is about 17 minutes. A
maximum of 64 messages can be recorded.
Note:...

Handset / Base unit
1 MMENU N#304
2 MYES N
3 Proceed with the operation for your unit.
Handset:  M OFF N
Base unit:  M EXIT N
Playing back the greeting message
Handset / Base unit
1 MMENU N#303
2 Proceed with the operation for your unit.
Handset:  To exit, press  MOFF N.
Base unit:  To exit, press  MEXIT N.
Listening to messages
Important:
R If your phone service provider offers voicemail
service, the voicemail service may answer calls
before the base unit’s built-in answering system
has a chance to...