Panasonic Kx Tg6632 Operating Instructions Manual

							Error messages
Display message Cause/solution
Base no power
o r
No link. Re-connect
base AC adaptor.
or
No link. R
The handset has lost communication with the
base unit. Move closer to the base unit and try
again.
R Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.
R The handset’s registration may have been
canceled. Re-register the handset (page 33).
R When “ No link. ” is displayed during a
power failure, place a handset on the base
unit to supply power to the base unit.
Busy RT
he called unit is in use.
ROther units are in use and the system is busy.
Try again later.
R The handset you are using is too far from the
base unit. Move closer and try again.
Call phone company for
y
 our access # R
You have not stored the voice mail access
number. Store the number (page 45).
Check tel line RT
he supplied telephone line cord has not been
connected yet or not connected properly.
Check the connections (page 9).
Error!! RR
ecording was too short. Try again.
Invalid RT
here is no handset registered to the base
unit matching the handset number you
entered.
R The handset is not registered to the base unit.
Register the handset (page 33).
Requires subscription
t
 o Caller ID. R
You must subscribe to a Caller ID service.
Once you receive caller information after
subscribing to a Caller ID service, this
message will not be displayed.
Use rechargeable
b
 attery. R
A wrong type of battery such as Alkaline or
Manganese was inserted. Use only the
rechargeable Ni-MH batteries noted on page 4,
6. For assistance, please visit http://www.panasonic.com/help
51Useful Information 
						

							Troubleshooting
I
f you still have difficulties after following the instructions in this section, disconnect
the base unit’s AC adaptor, then reconnect the base unit’s AC adaptor. Remove the
batteries from the handset, and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn
o
 n even after installing
charged batteries. R
Place the handset on the base unit or charger to
turn on the handset.
The unit does not work. RM
ake sure the batteries are installed correctly
(page 9).
R Fully charge the batteries (page 9).
R Check the connections (page 9).
R Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.
R The handset has not been registered to the base
unit. Register the handset (page 33).
I cannot hear a dial tone. RT
he base unit’s AC adaptor or telephone line cord
is not connected. Check the connections.
R Disconnect the base unit from the telephone line
and connect the line to a known working
telephone. If the working telephone operates
properly, contact our service personnel to have the
unit repaired. If the working telephone does not
operate properly, contact your service provider/
telephone company.
The indicator on the
h
 andset flashes slowly. R
New messages have been recorded. Listen to the
new messages (page 40).
R New voice mail messages have been recorded.
Listen to the new voice mail messages (page 46). Programmable settings
Problem Cause/solution
The display is in a
l
 anguage I cannot read. R
Change the display language (page 14).
I cannot register a handset
t
 o a base unit. R
The maximum number of handsets (6) is already
registered to the base unit. Cancel unused
handset registrations from the base unit (page 33). 52
For assistance, please visit http://www.panasonic.com/helpUseful Information 
						

							Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
Battery charge is low. Fully charge the batteries
(page 9).
I fully charged the batteries,
b
 ut
–  still flashes,
–  is displayed, or
–

the operating time seems to be shorter. R
C
lean the battery ends ( ,  ) and the charge
c
ontacts with a dry cloth and charge again.
R It is time to replace the batteries (page 9). Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
T
he handset is too far from the base unit. Move
closer.
R The base unit’s AC adaptor is not properly
connected. Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit.
Register it (page 33).
Noise is heard, sound cuts
i
 n and out. R
You are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
R Move closer to the base unit.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your DSL/
ADSL provider for details.
The handset does not ring. RT
he ringer volume is turned off. Adjust the ringer
volume (page 17).
R Silent mode is turned on. Turn it off (page 31).
The base unit does not ring. RT
he ringer volume is turned off. Adjust the ringer
volume (page 17).
I cannot make a call. RT
he dialing mode may be set incorrectly. Change
the setting (page 14).
R The handset is too far from the base unit. Move
closer and try again.
I cannot make long
d
 istance calls. R
Make sure that you have long distance service. For assistance, please visit http://www.panasonic.com/help
53Useful Information       
						

							Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d isplayed. R
You must subscribe to Caller ID service. Contact
your service provider/telephone company for
details.
R If your unit is connected to any additional
telephone equipment such as a Caller ID box or
cordless telephone line jack, plug the unit directly
into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your DSL/
ADSL provider for details.
R The name display service may not be available in
some areas. Contact your service provider/
telephone company for details.
R Other telephone equipment may be interfering with
this unit. Disconnect the other equipment and try
again.
Caller information is
d
 isplayed or announced
late. R
Depending on your service provider/telephone
company, the unit may display or announce the
caller’s information at the 2nd ring or later.
R Move closer to the base unit.
Caller information is not
a
 nnounced. R
The handset or base unit’s ringer volume is turned
off. Adjust it (page 17, 28).
R The Talking Caller ID feature is turned off. Turn it
on (page 28).
R The number of rings for the answering system is
set to  “2 rings ” or  “Toll saver ”. Select a
different setting (page 43).
R If the base unit and another handset are having an
intercom call, your handset does not announce
caller information.
The caller list/incoming
p
 hone numbers are not
edited automatically. R
The Caller ID number auto edit feature is turned
off. Turn it on and try again (page 28).
R You need to call back the edited number to
activate Caller ID number auto edit.
I cannot dial the phone
n
 umber edited in the caller
list. R
The phone number you dialed might have been
edited incorrectly (for example, the long distance
“1” or the area code is missing). Edit the phone
number with another pattern (page 36).
Time on the unit has
s
 hifted. R
Incorrect time information from incoming Caller ID
changes the time. Set the time adjustment to
“Manual ” (off) (page 28). 54
For assistance, please visit http://www.panasonic.com/helpUseful Information 
						

							Problem Cause/solution
The 2nd caller’s
i nformation is not displayed
during an outside call. R
In order to use Caller ID, call waiting, or Call
Waiting Caller ID (CWID), you must first contact
your service provider/telephone company and
subscribe to the desired service.
After subscribing, you may need to contact your
service provider/telephone company again to
activate this specific service, even if you already
subscribed to both Caller ID and Call Waiting with
Caller ID services (CWID). Answering system
Problem Cause/solution
The unit does not record
n
 ew messages. R
The answering system is turned off. Turn it on
(page 38).
R The message memory is full. Erase unnecessary
messages (page 40).
R The recording time is set to  “Greeting only ”.
Change the setting (page 43).
R If you subscribe to a voice mail service, messages
are recorded by your service provider/telephone
company, not your telephone. Change the unit’s
number of rings setting or contact your service
provider/telephone company (page 43).
I cannot operate the
a
 nswering system. R
Someone is using the unit. Wait for the other user
to finish.
R A caller is leaving a message. Wait for the caller to
finish.
R The handset is too far from the base unit. Move
closer.
I cannot operate the
a
 nswering system remotely. R
The remote access code is not set. Set the remote
access code (page 41).
R You are entering the wrong remote access code. If
you have forgotten your remote access code,
enter the remote access code setting to check
your current code (page 41).
R Press each key firmly.
R The answering system is turned off. Turn it on
(page 42). For assistance, please visit http://www.panasonic.com/help
55Useful Information 
						

							Liquid damage
Problem Cause/solution
Liquid or other form of
m oisture has entered the
handset/base unit. R
Disconnect the AC adaptor and telephone line
cord from the base unit. Remove the batteries
from the handset and leave to dry for at least 3
days. After the handset/base unit are completely
dry, reconnect the AC adaptor and telephone line
cord. Insert the batteries and charge fully before
use. If the unit does not work properly, contact an
authorized service center. Caution:
R
T

o avoid permanent damage, do not use a microwave oven to speed up the drying
process.
56 For assistance, please visit http://www.panasonic.com/helpUseful Information 
						

							FCC and other information
For assistance, please visit http://www.panasonic.com/help
57Useful InformationThis equipment complies with Part 68 of the 
FCC rules and the requirements adopted by 
the ACTA. On the bottom of this equipment 
is a label that contains, among other 
information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided 
to the telephone company.
L Registration No.............(found on the 
bottom of the unit)
L Ringer Equivalence No. (REN).......0.1B
A plug and jack used to connect this 
equipment to the premises wiring and 
telephone network must comply with the 
applicable FCC Part 68 rules and 
requirements adopted by the ACTA. A 
compliant telephone cord and modular plug 
is provided with the product. It is designed 
to be connected to a compatible modular 
jack that is also compliant.
The REN is used to determine the number 
of devices that may be connected to a 
telephone line. Excessive RENs on a 
telephone line may result in the devices not 
ringing in response to an incoming call. In 
most but not all areas, the sum of RENs 
should not exceed five (5.0). To be certain 
of the number of devices that may be 
connected to a line, as determined by the 
total RENs, contact the local telephone 
company. For products approved after July 
23, 2001, the REN for the product is part of 
the product identifier that has the format 
US:AAAEQ##TXXXX. The digits 
represented by ## are the REN without a 
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the 
telephone network, the telephone company 
will notify you in advance that temporary 
discontinuance of service may be required. 
But if advance notice isnt practical, the 
telephone company will notify the customer 
as soon as possible. Also, you will be 
advised of your right to file a complaint with 
the FCC if you believe it is necessary.The telephone company may make changes 
in its facilities, equipment, operations or 
procedures that could affect the operation of 
the equipment. If this happens the 
telephone company will provide advance 
notice in order for you to make necessary 
modifications to maintain uninterrupted 
service.
If trouble is experienced with this 
equipment, for repair or warranty 
information, please contact a Factory 
Service Center or other Authorized Servicer. 
If the equipment is causing harm to the 
telephone network, the telephone company 
may request that you disconnect the 
equipment until the problem is resolved.
Connection to party line service is subject to 
state tariffs. Contact the state public utility 
commission, public service commission or 
corporation commission for information.
If your home has specially wired alarm 
equipment connected to the telephone line, 
ensure the installation of this equipment 
does not disable your alarm equipment. If 
you have questions about what will disable 
alarm equipment, consult your telephone 
company or a qualified installer.
This equipment is hearing aid compatible as 
defined by the FCC in 47 CFR Section 
68.316.
When you hold the phone to your ear, noise 
might be heard in your Hearing Aid. Some 
Hearing Aids are not adequately shielded 
from external RF (radio frequency) energy. If 
noise occurs, use an optional headset 
accessory or the speakerphone option (if 
applicable) when using this phone. Consult 
with your audiologist or Hearing Aid 
manufacturer about the availability of 
Hearing Aids which provide adequate 
shielding to RF energy commonly emitted 
by digital devices.
   
						

							58
For assistance, please visit http://www.panasonic.com/helpUseful InformationWHEN PROGRAMMING EMERGENCY 
NUMBERS AND(OR)  MAKING TEST 
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to 
the dispatcher the reason for the call.
2) Perform such activities in the off-peak 
hours, such as early morning or late 
evenings.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.
Privacy of communications may not be 
ensured when using this phone.
CAUTION:Any changes or modifications not expressly 
approved by the party responsible for 
compliance could void the user’s authority 
to operate this device.
NOTE:This equipment has been tested and found 
to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide 
reasonable protection against harmful 
interference in a residential installation. This 
equipment generates, uses, and can radiate 
radio frequency energy and, if not installed 
and used in accordance with the 
instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a particular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by 
turning the equipment off and on, the user is 
encouraged to try to correct the interference 
by one or more of the following measures:
– Reorient or relocate the receiving 
antenna.
– Increase the separation between the 
equipment and receiver.
– Connect the equipment into an outlet on a 
circuit different from that to which the 
receiver is connected.– Consult the dealer or an experienced 
radio/TV technician for help.
Some cordless telephones operate at 
frequencies that may cause interference to 
nearby TVs and VCRs. To minimize or 
prevent such interference, the base of the 
cordless telephone should not be placed 
near or on top of a TV or VCR. If  
interference is experienced, move the 
cordless telephone further away from the TV 
or VCR. This will often reduce or eliminate 
interference.
FCC RF Exposure Warning:
L This product complies with FCC radiation 
exposure limits set forth for an 
uncontrolled environment. 
L To comply with FCC RF exposure 
requirements, the base unit must be 
installed and operated 20 cm (8 inches) 
or more between the product and all 
person’s body (excluding extremities of 
hands, wrist and feet). 
L This product may not be collocated or 
operated in conjunction with any other 
antenna or transmitter.
L The handset may be carried and operated 
with only the specific provided belt-clip. 
Other non-tested belt-clips or similar 
body-worn accessories may not comply 
and must be avoided.
Notice
L FCC ID can be found inside the battery 
compartment or on the bottom of the 
units. 
Compliance with TIA-1083 standard:
Telephone handsets identified with this logo 
have reduced noise and interference when 
used with T-Coil equipped hearing aids and 
cochlear implants.
T
Compatible with
Hearing Aid T-Coil
TIA-1083  
						

							Guía Rápida EspañolaP
ara  o bte n er  a yu da,  v is it e  h ttp ://w ww.p an aso nic .c o m /h elp  (s o lo  e n  in glé s)59 Guía Rápida Española  
Instalación
Unidad base
Filtro DSL/ADSL*
Correcto Incorrecto
Auricular
CargadorO
CARGUE 
APROXIMADAMENTE 
DURANTE 7 HORAS
L Use solo el adaptador de corriente Panasonic PNLV226 incluido.
(120 V CA, 60 Hz)
A la toma de  
teléfono de  
línea única 
(RJ11C)
L Use solo el adaptador de 
corriente Panasonic 
PNLV226 incluido. L UTILICE SOLO baterías de Ni-MH tamaño AAA 
(R03).
L NO utilice baterías Alcalinas, de Manganeso o de 
Ni-Cd.
L Compruebe que las polaridades son las correctas 
(S, T).
(120 V CA, 60 Hz)
SOLO baterías Ni-MH recargables
“Clic”
“Clic”
Ganchos
Oprima firmemente 
el contacto.
Confirme que 
aparezca 
“Cargando”. *Requiere un filtro DSL/ADSL (no incluido) si tiene este tipo de servicio.  
						

							60P
ara  o bte n er  a yu da,  v is it e  h ttp ://w ww.p an aso nic .c o m /h elp  (s o lo  e n  in glé s)  Guía Rápida EspañolaSugerencias de operación
Teclas de funciónEl auricular incluye 3 teclas de función. Al oprimir una tecla 
de función, puede seleccionar la función que aparece 
directamente encima de ella en la pantalla.
{C}, {MENU}, {REMR.} y otras funciones adicionales se 
asignan a las teclas de función. Preste atención a la 
pantalla para ver qué funciones están asignadas a las 
teclas de función durante la operación del auricular.
Tecla navegadora
Auricular:
{^}, {V}, {}: Navegue por diversas listas y 
elementos.
? VOL. (Volumen: {^} o {V}): Ajuste el volumen del 
receptor o el altavoz mientras habla.
{} REDIAL (Remarcación): Vea la lista de 
remarcación.
Unidad base (serie KX-TG6641):
{^}, {V}, {7} o {8}: Navegue por diversas listas y 
elementos.
{^} o {V} (Volumen): Ajuste el volumen del altavoz 
mientras habla.
{7} CID (Identificador de llamadas): Vea la lista de 
personas que llamaron.
{8} REDIAL (Remarcación): Vea la lista de 
remarcación.
{7}/{8}: Repetir u omitir el mensaje durante la 
reproducción.
Cambio de idiomas (predeterminado: “English”)
Cuando instale las baterías por primera vez, es posible que aparezca “Date and time 
Press SELECT”. Oprima {OFF} para salir.
Idioma de la pantalla
Auricular:
{MENU} (11) s {r}: “Español” s {GUARDA} s {OFF}Unidad base (serie KX-TG6641):{DISPLAY} s {r}: “Change language” s {6} s {r}: “Español” s {6}
Idioma de la guía de voz
Auricular:
{MENU} (112 s {r}: “Español” s {GUARDA} s {OFF}
{V} {^}
{}
Subir volumen
Bajar volumen
Auricular
{V} {^}
{7}{8}
Subir volumen
Bajar volumen
Unidad base