Panasonic Kx Tg5100 Operating Instructions Manual

61
Remote Operation from a Touch Tone Phone
Answering System
For assistance, please call: 1-800-211-PANA(7262)
Direct Remote Operation
Once you have accessed one of the mailboxes (p. 58), you can also control your 
unit by direct commands instead of using the voice menu. To end the remote 
operation, hang up anytime.
Direct commands
Turning on the Answering System
Call your unit and wait for 15 rings.
•The unit will answer and the greeting will be played.
•The Answering System will turn on. Hang up or...

62
Wall Mounting
This unit can be mounted on a wall phone plate.
1Connect the AC adaptor. 
2Tuck the telephone line cord inside the wall mounting adaptor ( ). 
Connect the telephone line cord ( ).
3Insert ( ) and ( ) hooks on the wall mounting adaptor into the holes 
on the base unit.
To Power 
Outlet 
1
2
#
$
AB
A
B 

63
Wall Mounting
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4Adjust the adaptor to hold the base unit, then push it in the direction of 
the arrow until it clicks into place.
5Connect the telephone line cord. Mount the unit, then slide down.
•Raise the antennas.
6To charge the handset battery:
Place the handset on the base unit.
•The CHARGE indicator lights. 

Wall Mounting
64
To remove the wall mounting adaptor
While pushing down the RELEASE LEVERS ( ), remove the adaptor ( ).
Charger unit (KX-TG5110M Only)
The charger can be wall mounted. Connect the AC adaptor. Install screws 
using the wall template (see below). Mount the charger ( ). Slide it down 
( ), then slide down to the right ( ) until it is secured.
Wall Template for the Charger unit
12
RELEASE
LEVERS
#
$
#
1
23
$
#
%
6.15 cm(2 13⁄32)
Screws 
To Power 
Outlet 
6.15 cm (2 13⁄32) 

65For assistance, please call: 1-800-211-PANA(7262)
Useful Information
Belt ClipHandset
You can hang the handset on your belt or pocket using the belt clip.
To attach the belt clip To remove the belt clip  
Optional Headset
Plugging the optional headset into the handset allows for hands-free phone 
conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88, 
KX-TCA91, KX-TCA92 or KX-TCA98 headset. To order, call the accessories 
telephone number on page 2.
Connecting an optional headset
Open...

66
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you want to use the handset with a 
different base unit of the same model, it is necessary to cancel the registration from 
the current base unit.
Only one handset can be canceled at a time near the base unit.
Make sure the handset and the base unit are not being used.
•“[-]” is shown on the top right of the display. 
•After canceling registration, the handset cannot be used. If you...

67
Canceling Registration/Re-registration
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different base unit of the 
same model, you need to register it to that base unit. The handset will be given a 
new extension number of that base unit. Only one handset can be registered at a 
time near the base unit. 
Make sure the base unit and the other handsets are not being used. 
Registration must be...

68
If the Following Appear on Your Display...
If the unit detects a problem, one of the following messages will be displayed on the 
handset or the base unit. Error beeps or a busy tone will sound.
Display messageCause & Remedy
Recharge battery(handset only)•The battery needs to be charged. Recharge the 
battery (p. 13).
Charge for 6 HRS(handset only)•The battery has been discharged. The handset will 
not work. Charge the battery fully (p. 13).
No link to base.
Walk closer to 
base and try 
again....

69
If the Following Appear on Your Display...
Useful Information
For assistance, please call: 1-800-211-PANA(7262) System is busy.
Please try again
later.•If more than one unit is in use, such as conducting 
external/intercom calls or listening to messages, you 
may not be able to use another unit. Try again later.
•If you try to program with the handset or base unit 
and another user is listening to messages, this 
display will be shown. Try again later.
•If 2 other users are listening to messages, or...

If the Following Appear on Your Display...
70
Memo record
Mailbox1
Recording error(base unit only)•“Your message was not recorded. Record your message 
again.” is announced. The message was not recorded 
correctly. Record it again (p. 57).
All mailbox full(base unit only)•The remaining recording time or the number of 
messages which can still be recorded is 0. 
Erase unnecessary messages (p. 56), and record 
your greeting or memo message (p. 21, 57).
     Error!!
8 handsets have
already been
registered....