Panasonic Kx Tg4731 Operating Instructions Manual

Voice mail service
V oice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service,
your service provider/telephone company’s
voice mail system answers calls for you when
you are unavailable to answer the phone or
when your line is busy. Messages are
recorded by your service provider/telephone
company, not your telephone. Please contact
your service provider/telephone company for
details of this service.
Important:
R To use the voice...

Listening to voice mail messages
T
he unit lets you know that you have new
voice mail messages in the following ways:
– “New Voice Mail ” is displayed on the
handset if message indication service is
available.
– The message indicator on the handset flashes slowly if the message alert feature
is turned on (“Message alert”, page 39). Handset
1 MV

MN
or
M MENU N#330
R The speakerphone turns on.
R If there are no new messages in the
voice mail,  MVM N is not displayed.
2 Follow the pre-recorded...

Intercom
I ntercom calls can be made:
– between handsets
– between a handset and the base unit *1
*1 KX-TG4741/KX-TG4761 series: page 3
Note:
R When paging unit(s), the paged unit(s)
beeps for 1 minute.
R If you receive an outside call while talking
on the intercom, you hear 2 tones.
– To answer the call with the handset,
press  MOFF N, then press  M N
.
–

To answer the call with the base unit, press  MSP-PHONE N 2 times. *1
*1 KX-TG4741/KX-TG4761 series: page 3 Making an intercom call
Handset
1 MM...

4
To complete the transfer:
Press  MOFF N.
R The outside call is being routed to the
destination unit.
To establish a conference call:
M MENU N a  M b N:  “Conference ” a
M SELECT N
R To leave the conference, press  MOFF N.
The other 2 parties can continue the
conversation.
R To put the outside call on hold:
MMENU N a  M b N:  “Hold ” a
M SELECT N
To resume the conference:  MMENU N
a  M b N:  “Conference ” a  M SELECT N Base unit
*
 1
*1 KX-TG4741/KX-TG4761 series: page 3
1 During an outside call, press...

Wall mounting
N ote:
R Make sure that the wall and the fixing
method are strong enough to support the
weight of the unit. Base unit
1
T

hread the AC adaptor cord and
telephone line cord through the hole in
the wall mounting adaptor in the direction
of the arrow. 2
T
uck the telephone line cord inside the
wall mounting adaptor ( A). Connect the
AC adaptor cord and telephone line cord
( B ). 3
I
nsert the hooks on the wall mounting
adaptor into holes   and   on the base
u
nit. 4
A
djust the adaptor to...

5
Mount the unit on a wall then slide down
to secure in place. To remove the wall mounting adaptor
W
hile pushing down the release levers ( A),
remove the adaptor ( B). Charger
D

rive the screws (not supplied) into the wall. 46
For assistance, please visit http://www.panasonic.com/helpUseful Information
TG47xx(en-en)_1118_ver022.pdf   462011/11/18   10:26:19AC adaptor cord
83 mm 
(31/4 inches)
or
102 mm 
(4 inches)
1
2
Wall phone plate
83 mm
(3 1/4 inches)102 mm
(4 inches)
2 1 AA
B 25.4 mm
(1 inch)...

Error messages
Display message Cause/solution
Base no power
o r
No link. Re-connect base
AC adaptor. R
The handset has lost communication with the base
unit. Move closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset’s registration may have been canceled.
Re-register the handset (page 31).
Busy RT
he called unit is in use.
ROther units are in use and the system is busy. Try
again later.
R The handset you are using...

Troubleshooting
I f you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn on
e
 ven after installing charged
batteries. R
Place the handset on the base unit or charger to turn on
the handset.
The unit does not work. RM
ake sure the batteries are...

Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
Battery charge is low. Fully charge the batteries (page 11).
I fully charged the batteries, but
–  still flashes,
–  is displayed, or
–

the operating time seems to be shorter. R
C
lean the battery ends ( ,  ) and the charge contacts
w
ith a dry cloth and charge again.
R It is time to replace the batteries (page 11). Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
T
he handset is too far from the base...

Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d isplayed. R
You must subscribe to Caller ID service. Contact your
service provider/telephone company for details.
R If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless telephone
line jack, plug the unit directly into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL...