Panasonic Kx Tg2564 Operating Instructions Manual

							4
Connect the telephone line cord. 
Mount the base unit, then slide 
down.
≥Raise the antennas.
Charger unit
The charger can be wall mounted. Connect the AC adaptor. Install screws
using the wall template (p. 60). Mount the charger (1). Slide it down (2),
then slide down to the right (3) until it is secured.
61For assistance, please call: 1-800-211-PANA(7262)
Useful Information
1
2
3
Screws
To Power 
Outlet
Wall Phone 
Plate
To temporarily set the handset down
during a conversation, place it as
shown here.
2.4 cm
(15⁄16q) 
						

							62
Optional Headset
Plugging an optional headset into the cordless handset allows a hands-
free phone conversation. Please use only the Panasonic KX-TCA88
headset. To order, call the accessories telephone number on page 2.
Connecting the optional headset to the cordless handset
Open the headset jack cover, and connect the optional headset to the
headset jack as shown below.
When the optional headset is connected to the cordless handset,
make sure to use the headset to talk with the caller. If you want to
have a normal cordless phone conversation, disconnect the
headset.
Headset Jack
Belt Clip
You can hang the cordless handset on your belt or pocket using the belt
clip.
To attach the belt clip To remove the belt clip 
						

							63For assistance, please call: 1-800-211-PANA(7262)
Useful Information
Battery Replacement
If “Recharge battery” is displayed and/or “” flashes after a few
telephone calls even if the battery was fully charged, replace the battery
with a new Panasonic PQP510SVC (P-P510) battery. To order, call the
accessories telephone number on page 2.
Push 
forward.
Red 
Lead
Black 
Lead
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose
of this battery into your municipal waste stream. Please
call 1-800-8-BATTERY for information on how to recycle
this battery.
4
Make sure you charge the new battery for about
15 hours in order to display the battery strength
prompt correctly (p. 11).
2
Replace the battery. Then
place the battery leads inside
the groove, otherwise the
leads may be damaged when
closing the cover.
1
Carefullyinsert a flat metal
object in the slot, and push
forward to release the lock.
Remove the cordless handset
cover.
3
Close the cover.1
2 
						

							If the unit detects a problem, one of the following messages will be
displayed on the cordless handset or the base unit.
Cordless handset display
The battery needs to be charged. Place the
cordless handset on the charger to charge the
battery (p. 12).
The cordless handset has lost communication
with the base unit. Move closer to the base unit
and try again.
When trying to store an item or Caller List
information in the directory, the directory
memory is full (p. 36, 40). To erase other stored
items from the directory, see page 46.
If the Following Appear...
Recharge battery
No link to base.
Walk closer to
base & try again
Directory full
Adding Another Phone
64
T-Adaptor (KX-J66)Standard Telephone
Telephone 
Line Cord
Single-Line 
Telephone Jack
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2. 
						

							65For assistance, please call: 1-800-211-PANA(7262)
Useful Information
While the base unit was being used, (›)or (‹)
was pressed to search the Caller List/directory
list, 
(fl)was pressed to select an option or
(CLEAR/INTERCOM/HOLD)was pressed.
While storing items in the directory, the cordless
handset has lost communication with the base
unit. Move closer to the base unit and try again.
The display will be shown while the base unit is
engaged in an outside call.
Base unit display
When the clock needs adjusting, the time and
date flashes. Adjust the clock (p. 13).
The display will be shown while the cordless
handset is engaged in an outside call.
While the cordless handset was being used, 
(›)
or (‹)was pressed to search the Caller
List/directory list or 
(FUNCTION/EDIT)or (VM)
was pressed. Base in use
Save error
Line in use
12:00AM JAN. 1
Line in use
Portable in use 
						

							Troubleshooting
66
Problem
“No link to base.
Walk closer to base &
try again” is displayed on
the cordless handset display
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The cordless handset does
not ring.
The cordless handset
display is blank.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the unit starts to
ring and stops the
program/search.
Cause and Remedy
≥You are too far from the base unit.
Move closer and try again.
≥Raise the base unit antennas.
≥Plug in the AC adaptor of the base unit.
≥The cordless handset may lose
communication with the base unit.
Set the security code (p. 59).
≥Locate the cordless handset and the
base unit away from other electrical
appliances (p. 3).
≥Move closer to the base unit.
≥Raise the base unit antennas.
≥Press 
(fi)to select a clearer channel in
the talk or intercom mode.
≥The ringer volume is set to OFF. Set to
HIGH or LOW (p. 20).
≥Charge the battery fully (p. 11).
≥You cannot store an item in the
directory while the base unit is in the
talk or intercom mode.
≥Do not pause for over 60 seconds while
storing.
≥To answer the call, press  . Start
again from the beginning after hanging
up.
Cordless handset 
						

							67For assistance, please call: 1-800-211-PANA(7262)
Useful Information
“
Problem
The cordless handset does
not display the caller’s name
and/or phone number.
The cordless handset
display exits the Caller List
or directory.
When a second call is
received during a
conversation, the cordless
handset does not display the
new caller’s name and/or
phone number.
You cannot page the base
unit.
You cannot redial by
pressing 
(REDIAL/PAUSE).
Cause and Remedy
≥You need to subscribe to a Caller ID
service.
≥Other telephone equipment may be
interfering with your phone. Disconnect
it and try again.
≥Other electrical appliances connected to
the same outlet may be interfering with
the Caller ID information.
≥Telephone line noise may be affecting
the Caller ID information.
≥Do not pause for over 60 seconds while
searching.
≥The line mode selection is incorrect.
See page 16.
≥The caller requested not to send his/her
information. See page 29.
≥The cordless handset is too far from the
base unit.
≥The base unit is engaged in an outside
call, viewing the Caller List/directory list.
Try again later. Wait until “Base in
use” disappears.
≥If the last number dialed was more than
32 digits long, the number will not be
redialed correctly.
≥The button has a double function as
either redial or pause. It will redial the
last number dialed if pressed at the
outset of a call (p. 24). If another
number has been dialed first, it will
operate as a pause button (p. 57). 
						

							“ Troubleshooting
68
Problem
You cannot have a
conversation using the
cordless handset.
You cannot have a
conversation using the
optional headset.
Cause and Remedy
≥When the optional headset is connected
(p. 62), you must use the headset to talk
with the caller. To have a normal
cordless phone conversation, disconnect
the headset.
≥Make sure that the headset is
connected properly (p. 62).
Problem
The base unit does not ring.
While programming or
searching, the base unit
starts to ring and stops the
program/search.
The base unit does not
display the caller’s name
and/or phone number.
The base unit display exits
the Caller List.
When a second call is
received during a
conversation, the base unit
does not display the new
caller’s information.
Cause and Remedy
≥The ringer volume is set to OFF. Select
HIGH or LOW (p. 20).
≥To answer the call, lift the handset or
press 
(DIGITAL–SP-PHONE). Start again
from the beginning after hanging up.
≥You need to subscribe to a Caller ID
service.
≥Other telephone equipment may be
interfering with your phone. Disconnect
it and try again.
≥Other electrical appliances connected to
the same outlet may be interfering with
the Caller ID information.
≥Telephone line noise may be affecting
the Caller ID information.
≥Do not pause for over 60 seconds while
searching.
≥The line mode selection is incorrect.
See page 16.
≥The caller requested not to send his/her
information. See page 29.
Base unit 
						

							“
69For assistance, please call: 1-800-211-PANA(7262)
Useful Information
Problem
You cannot page a cordless
handset.
You cannot redial by
pressing 
(REDIAL).
Cause and Remedy
≥The cordless handset is too far from the
base unit.
≥The cordless handset is engaged in an
outside call or viewing the Caller
List/directory list. Try again. Wait until
“Portable in use” disappears.
≥If the last number dialed was more than
32 digits long, the number will not be
redialed correctly.
Problem
The unit does not work.
You cannot program items,
such as the dialing mode.
Cause and Remedy
≥Check the settings (p. 10–16).
≥Charge the battery fully (p. 11).
≥Clean the charge contacts and charge
again (p. 12).
≥Install the battery properly (p. 63).
≥Place the cordless handset on the
charger and unplug the AC adaptor of
the base unit to reset. Plug in, and try
again.
≥Programming is not possible while the
unit is in the talk, speakerphone or
intercom mode, or when viewing the
Caller List/directory list.
≥Do not pause for over 60 seconds while
programming.
≥Move closer to the base unit, if you use
the cordless handset.
≥Make sure that the unit is not being
used.
General 
						

							“ Troubleshooting
70
Problem
Previously programmed
information is erased.
“Recharge battery” is
displayed on the cordless
handset, “” flashes or
the unit beeps intermittently.
You charged the battery
fully, but “Recharge
battery” is still displayed
and/or “” continues to
flash.
If you cannot solve your
problem
Cause and Remedy
≥If a power failure occurs, programmed
information may be erased. Reprogram
if necessary.
≥Charge the battery fully (p. 11).
≥Clean the charge contacts and charge
again (p. 12).
≥Install a new battery (p. 63).
≥Call our customer call center at
1-800-211-PANA(7262).
≥Panasonic’s e-mail address for
customer inquiries:
[email protected] 
for customers in the USA or Puerto Rico
ONLY