Panasonic Kx Tg2563 Operating Instructions Manual

11
PreparationNANCY BROWN
1-000-222-3333
----Waiting-----
A second call is received during a conversation 
(p. 52).
Ö, Ñ, BACKÜor FWD/EDITáwas pressed
with the handset while the handset was on the
base unit. Lift the handset and press the button
again.
While the base unit was not in the standby mode,
Öor Ñwas pressed to search the Caller
List/directory list, 
FWD/EDITáwas pressed to
select an option or 
(INTERCOM/CLEAR)was
pressed.
When trying to store an item or Caller List
information in the directory,...

Settings
12
Connections
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10 (Order No. PQLV10Z).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 58.
•If your unit is connected to a PBX which does not support Caller ID and voice
mail services, you cannot access those services.
Hooks Hooks
AC Adaptor
Telephone Line 
Cord
Power Outlet 
(AC 120 V, 60 Hz)
Raise the
antennas.Single-Line 
Telephone...

13
Preparation
Needs to be recharged.
Battery Charge
Place the handset on the base unit
and charge for about 6 hoursbefore
initial use.
•The IN USE/CHARGE indicator lights and
a beep sounds. 
Battery strength
You can check the battery strength on the handset display while the
handset is on the base unit, while it is in use (making/answering a call
etc.), or after viewing the Caller List or directory items, programming etc.
The battery strength will remain for 5 seconds after using the handset,
then the...

14
Settings
Up to 3.5 hours
Up to 11 days
Recharge
Recharge the battery when:
—“Recharge battery” is displayed on 
the handset,
—“ ” flashes on the display, or
—the handset beeps intermittently while it is in use.
•If you DO NOT recharge the handset battery for more than 15 minutes, the
display will keep indicating “Recharge battery” and/or “” will continue
to flash.
Battery information
After your Panasonic battery is fully charged (p. 13):
OperationApprox. battery life
While in use
(TALK)Up to 4.5 hours...

15
Preparation
Selecting the Dialing Mode
You can program the dialing mode using the handset near the base
unit.
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the unit is in the standby mode initially. 
1
Press (FUNCTION/EXIT/CH).
2
Press Öor Ñrepeatedly until the arrow
points to “Program”.
3
Press FWD/EDITá(Yeskey).
4
Press Öor Ñrepeatedly until the arrow
points to “Set dial mode”.
5
Press...

16
Selecting the Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Otherwise the Call Waiting Caller ID Feature may not be used (p. 52).
Your phone comes from the factory set to “A”. 
Use the handset near the base unit.
Make sure the unit is in the standby mode initially.
1
Press (FUNCTION/EXIT/CH).
2
Press Öor Ñrepeatedly until the arrow
points to “Program”.
3
Press FWD/EDIT á(Yeskey).
4
Press Öor Ñrepeatedly until the arrow
points to “Set line mode”.
5
Press...

Programmable Functions
17
Preparation
HSave DIRECT#
Set flash time
Save mailbox#
Voicemail tone
Set line mode
Set dial mode
Talk switching You can program the following function items using the handset near
the base unit. The display shows the programming instructions. See the
corresponding pages for function details.
Make sure the unit is in the standby mode initially.
During programming:
*To select a desired function item, press 
Öor Ñrepeatedly until the
arrow points to the item. Then press 
FWD/EDIT...

18
Programmable Functions
Setting the Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing 
(TALK). If you want to use this feature, turn
the feature ON by programming. Your phone comes from the factory set
to OFF.
Make sure the unit is in the standby mode initially.
1
Press (FUNCTION/EXIT/CH).
2
Press Öor Ñrepeatedly until the arrow
points to “Program”.
3
Press FWD/EDIT á(Yeskey).
4
Press Öor Ñrepeatedly until the arrow
points to...

19
Preparation
Selecting the Ringer Volume
You can set the handset and base unit ringer volumes to HIGH, LOW or
OFF. If set to OFF, the handset/base unit will not ring. Your phone comes
from the factory set to HIGH.
Handset ringer volume
Make sure the unit is in the standby mode initially.
1
Press (FUNCTION/EXIT/CH).
2
Press Öor Ñrepeatedly until the
arrow points to “Ringer volume”,
and press 
FWD/EDIT á(Yeskey).
3
Press Öor Ñto select the
desired volume.
•The selected volume is displayed and rings.
•To...

Making Calls
20
1
Press (TALK).
2
Dial a phone number.
•The dialed number is displayed.
•After a few seconds, the display will show the
length of the call and the battery strength.
3
To hang up, press (TALK)or place the
handset on the base unit.
•If the handset has lost communication with the base unit, 3 beeps sound and “No
link to base. Place on cradle and try again.” is displayed.
If noise interferes with the conversation
Press (FUNCTION/EXIT/CH)to select a clearer channel or move closer to
the base...