Panasonic Kx Tg2343 Operating Instructions Manual

							Preparation
For assistance, please call: 1-800-211-PANA(7262)21
Preparing the Answering System
Number of Rings 
You can select the number of times the unit rings before the Answering System 
answers a call, from “2” to “7” or “Toll saver”*. The factory preset is “4”.  
5Select the recording time by pressing [d] or 
[B].
• You can also select the recording time by pressing 
[1], [2], [3] or [0] (Greeting only).
6Press Save, then press [OFF].
If you select “Greeting only”, the unit will answer calls with the greeting 
message, and then hang up. The unit will not record any incoming messages. 
The base unit will display “ ” instead of the number of messages.
1Press [MENU].
2Scroll to “Initial setting” by pressing [d] 
or [
B], then press Select.
3Press Select at “Set answering”.
4Press Select at “Number of rings”.
5Select the number of rings by pressing [d] or 
[
B].
• You can also select the number of rings by 
pressing [0] (Toll saver*), or [2] to [7].
6Press Save, then press [OFF].
*Toll saver
When you call the unit from a remote operation, the number of rings will tell you 
if there are any new messages. If the unit answers on the 2nd ring, there is at 
least one new message. If the unit answers on the 4th ring, there are no new 
messages. To save the toll charges for the call, hang up immediately when you 
hear the 3rd ring. The 3rd ring indicates that there are no new messages.
Recording time
:3min
Back     Save
KdBL
Handset
Initial setting
Back  SelectKdBL
Set answering
Back  SelectKdBL
Number of rings
Back  SelectKdBL
Number of rings
:4
Back     Save
KdBL
PQQX13984YA.book  21 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Preparing the Answering System
22
Message Alert   
You can select whether or not the Ringer/Message Alert indicator on the handset 
will flash slowly when new messages have been recorded (p. 45). The factory 
preset is OFF.
• The Ringer/Message Alert indicator will not flash for new messages while the 
handset is in use.
• The Ringer/Message Alert indicator acts both as a ringer indicator and as a 
message alert indicator. This indicator will flash rapidly when a call is received 
whether this feature is on or off.
 
• Battery operating time will be shortened when using this feature (p. 11).
1Press [MENU].
2Scroll to “Initial setting” by pressing [d] 
or
 [B], then press Select.
3Scroll to “Message alert” by pressing [d] or 
[B], then press Select.
4Select “On” or “Off” by pressing [d] or [B].
5Press Save, then press [OFF].
Handset
Initial setting
Back  SelectKdBL
Message alert
Back  SelectKdBL
Message alert
:Off
Back     Save
KdBL
PQQX13984YA.book  22 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Telephone System
For assistance, please call: 1-800-211-PANA(7262)23
Making Calls
 
To have a hands-free phone conversation  1
Press [C].
•“Talk” is displayed.
2Dial a phone number.
• The dialed number is displayed.
• After a few seconds, the display will 
show the length of the call.
3To hang up, press [OFF] or place 
the handset on the base unit.
1Press [s].
•“SP-phone” is displayed.
2Dial a phone number.
• The dialed number is displayed.
• After a few seconds, the display will show the length of the call.
3When the other party answers, talk into the microphone.
4To hang up, press [OFF] or place the handset on the base unit.
Hands-free Digital Duplex Speakerphone
For best performance, please note the following:
• Talk alternately with the other party in a quiet room.
 
• If you or the other party has difficulty hearing, press [d] to decrease the 
speaker volume.
• While talking using [C], you can switch to a hands-free phone conversation 
by pressing [s]. To switch back to the receiver, press [C].
Display
[d], [B]
[C]
[s]
[REDIAL] 
[OFF]
Soft Keys
Microphone
[HOLD] 
PQQX13984YA.book  23 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Making Calls
24
To dial after confirming the 
entered number  
To adjust the receiver/
speaker volume during a 
conversation
There are 3 volume levels for the 
receiver and  6 volume levels for the 
speaker. 
To increase volume, press [B]. 
To decrease volume, press [
d].
• The display shows the current volume 
setting.
• If you try to increase/decrease 
volume when it is at the maximum/
minimum level, the handset will beep 
3times.
To redial the last number 
dialedTo redial using the redial 
list (Memory Redial)
The last 5 phone numbers dialed are 
stored in the redial list.  
•To erase an item, scroll to the item 
then press Erase.
•If “No items stored” is displayed, 
the list is empty.
To put a call on hold
To return to the call, press [C] 
or [s].
• If another phone is connected on the 
same line (p. 9), you can also take the 
call by lifting its handset.
• If a call is kept on hold for 6 minutes, 
an alarm tone will start to sound and 
the Ringer/Message Alert indicator 
will start to flash rapidly. After 4 
additional minutes on hold, the call 
will be disconnected.
1Enter a phone number.
• If you misdial, press Clear. 
Enter the correct number.
• If a pause is required when 
dialing, press Pause where 
needed (p. 40).
• To cancel, press [OFF].
2Press [C] or [s].
3To hang up, press [OFF] or 
place the handset on the base 
unit.
Press [C] or [s], then press 
[REDIAL].
3334444|
Clear    PauseKL
Ex. Receiver volume: High
Speaker volume: Level 6
Volume
 Low   High
(VE)      Mute
KL
1Press [REDIAL].
• The last number dialed is 
displayed.
2Scroll to the desired number by 
pressing [
d] or [B].
• You can also scroll down through 
the list by pressing [REDIAL].
• To exit the list, press [OFF].
3Press [C] or [s].
Press [HOLD] during a 
conversation.
333-4444
Erase   KdB
Hold         
 Rcvd     Phone
calls    book 
KL
PQQX13984YA.book  24 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							For assistance, please call: 1-800-211-PANA(7262)25
Making Calls
Telephone System
Voice Enhancer Technology
Panasonic’s Voice Enhancer Technology clarifies the voice of the person you are 
talking to, reproducing a more natural-sounding voice that is easier to hear and 
understand.
Voice Enhancer Technology can be turned on or off. The factory preset is OFF. 
• Depending on the condition and quality of your telephone line, this feature may 
emphasize existing line noise. If it becomes difficult to hear, turn this feature off. 
To turn this feature on, press (VE) during a 
conversation. 
•“J” is displayed.
•To turn this feature off, press (VE)
 again. 
“J” disappears from the display.
• After hanging up a call, the on/off setting will be retained.
When the handset is not in use, you can also turn this feature on or off by 
programming as follows:
1. Press [MENU].
2. Scroll to “Voice enhancer” by pressing [
d] or [B], then press Select.
3. Select “On” or “Off” by pressing [
d] or [B].
4. Press Save, then press [OFF].
Backlit LCD display/Lighted handset keypad
The handset display and dialing buttons will light for a few seconds after pressing a 
button or lifting the handset off the base unit .
        J  5Talk
00-00-32
(VE)      Mute
KL
PQQX13984YA.book  25 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							26
Answering Calls
When a call is received, the unit rings, “Incoming call” is displayed, and the 
Ringer/Message Alert indicator on the handset and “ ” on the base unit 
flash rapidly. 
If you subscribe to Caller ID, see page 27.
Auto Talk
If the Auto Talk feature is turned on (p. 16), you can answer a call by simply lifting 
the handset off the base unit.
Temporary ringer off
You can turn the ringer off temporarily by pressing [OFF], while the handset is 
ringing for an outside call. The handset will ring again as normal the next time a call 
is received.
• If the ringer volume is turned off, the unit will not ring (p. 17).
1Press [C] or [s].
• You can also answer a call by 
pressing any button except [
d], [B] 
or [OFF].
2To hang up, press [OFF] or place 
the handset on the base unit.
LINEIN USE
[C][OFF]
[s]
Ringer/Message Alert 
Indicator 
PQQX13984YA.book  26 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Telephone System
For assistance, please call: 1-800-211-PANA(7262)27
Caller ID Service
This unit is compatible with Caller ID services offered by your telephone company. If 
you subscribe to Caller ID, caller names and phone numbers will be displayed and 
recorded in the Caller List.
How Caller ID information is displayed
When a call comes in, the unit will ring and Caller ID 
information will be received. The handset display will 
show the caller’s information.* 
• After you answer the call, the display will show the 
length of the call.
*Personalized Name Display
If you receive a call from one of the same phone numbers stored in the phone book, 
the handset will show the caller’s name stored in the phone book instead of 
incoming caller’s name.
• If the unit does not receive Caller ID information, one of the following will be 
displayed:
• Depending on the radio communications with the base unit, the handset may not 
display Caller ID information immediately after the first ring.
• If your unit is connected to a PBX which does not support Caller ID, you cannot 
access Caller ID service.
• Name display service may not be available in some areas. For further information, 
please contact your telephone company.
• If you subscribe to both Caller ID and Call Waiting with Caller ID services (CWID), 
when a second call is received while talking, a call waiting tone will be heard and 
the second caller’s information will be displayed on the handset in use (p. 39). 
Contact your telephone company for details about availability in your area, and to 
verify that CWID is activated on your telephone line.
DisplayMeaning
Out of areaThe caller dialed from an area which does not provide 
Caller ID service.
Private callerThe caller requested not to send his/her information.
Long distanceThe caller made a long distance call.
Example
ROBINSON,TINA
1-555-222-3333
PQQX13984YA.book  27 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							28
Using the Caller List
The unit can record information up to 30 different callers and store this information 
in the Caller List. Caller information is sorted by the most recent call to the oldest. 
When the 31
st call is received, the information from the 1st call is deleted.
The unit will also tell you how many calls you missed while you were out or 
unavailable to answer the phone.
• When new messages have been recorded (p. 45), “New message” will be 
displayed in place of missed calls display.
Viewing the Caller List   
• If there is no name information for a caller and you do not store the name and 
phone number in the phone book, the display will only show the phone number.
• If you do not press any buttons for 60 seconds, the unit will exit the Caller List.
1The display will show the number of calls 
you missed.
2Press Rcvd calls to review other calls 
logged in the Caller List.
• If there are no items in the Caller List, 
“Rcvd calls” will not be displayed.
• After viewing the missed call entries, 
“missed calls” will disappear from the 
display.
1Press Rcvd calls, [d], or [B] to enter the 
Caller List.
2To search from the most recent call, press [d]. 
To search from the oldest call, press [
B].
• The caller’s name, number and the time and date 
of the call are displayed. Name and phone number 
are alternately displayed as shown on the right.
3Press [OFF] to exit the list.
             
 2 missed calls 
    Charging
 2 missed calls
 Rcvd     Phone 
calls    book 
KL
Handset off the base unit
Handset on the base unit
1
1
2
Handset
 2 missed calls
 Rcvd     Phone 
calls    book 
KL
 2 missed calls
 =Scroll list
All erasedB
K
Ex. 2 calls missed.
Example
SMITH,JACK
 3:10P JUN.29
Erase   Select
KL
1-555-333-4444
 3:10P JUN.29
Erase   Select
KL
PQQX13984YA.book  28 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Using the Caller List
Telephone System
For assistance, please call: 1-800-211-PANA(7262)29
What “,” means
“,” indicates you have already viewed this calling 
information or answered the call. If the same caller calls 
again, the call entry with the “,” will be replaced with the 
new call entry.
If a caller calls more than once
The number of times the same caller called is displayed 
(“×2” to “×9”). The date and time of the most recent call will 
be recorded. After viewing a caller’s information, “×2” to 
“×9” will be replaced with “,”.
Calling Back from the Caller List 
• In some cases, you may have to edit the number before dialing (p. 30). 
(Ex. You may have to delete “1” and the area code.)
• If a phone number is not displayed in the caller information, you cannot call that 
caller back from the Caller List.
1Press Rcvd calls, [d], or [B] to enter the Caller List.
2Scroll to the desired caller by pressing [d] or [B]. 
3Press [C] or [s].
• The phone number is dialed.
SMITH,JACK
 3:10P JUN.29 ,
TURNER,CINDY
11:20A JUN.12 ×2
Ex. Called 2 times.
Handset
PQQX13984YA.book  29 ページ  ２００４年３月１５日　月曜日　午前８時２６分 
						

							Using the Caller List
30
Editing the Caller’s Phone Number 
You can edit a phone number in the Caller List by removing its area code and/or the 
long distance code “1”.  
Once you call back an edited number, this unit can automatically edit incoming 
phone numbers from the same area code in the Caller List and each time you 
receive a call (Caller ID Number Auto Edit, page 31).
• If you receive a call from a 7-digit phone number stored in the phone book, “Edit” 
will not be displayed in step 4.
1Press Rcvd calls, [d], or [B] to enter the 
Caller List.
2Scroll to the desired caller by pressing [d] or 
[
B].
3Press Select.
4Press Edit repeatedly until the number is 
shown in the desired format.
• Each time you press Edit, the number is 
rearranged into one of 3 patterns.
F  
G – 
H 1– –  
• The order in which patterns F – H are 
displayed depends on how the telephone 
number is displayed in step 2.
5To call the edited number, press [C] or [s].
• If Caller ID Number Auto Edit is turned on (factory preset is on), phone 
numbers with the same area code as the number you edited will now be 
edited in the Caller List and each time you receive a call.
• You can press [OFF] immediately after pressing [C] or [s] if you wish to 
activate the Auto Edit feature without actually dialing the number you just 
edited.
To save the edited number into the phone book, press Save.
• If there is no name information, see “Storing Caller Information in the Phone 
Book” on page 32, from step 4.
• Even if the Auto Edit feature is turned on, this feature will not be activated by 
saving the edited number in the phone book.
Handset
PARKER,FRED
11:20A JAN.12
Erase   Select
KL
1-555-321-5555
11:20A JAN.12
Erase   Select
KL
Phone no.
Area codePhone no.
Area codePhone no.
321-5555
Edit      SaveKL
555-321-5555
Edit      SaveKL
1-555-321-5555
Edit      SaveKL
F
G
H
PQQX13984YA.book  30 ページ  ２００４年３月１５日　月曜日　午前８時２６分