Panasonic Kx Tg2267 Operating Instructions Manual

11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Settings
Connecting the AC Adaptor
•USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1(Order No. KX-TCA1-G).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 60.
•If your unit is connected to a PBX which does not support Caller ID services and
voice mail services, you cannot access those services.
AC Adaptor
Raise the...

12
Connecting the Telephone Line Cord
Connect the telephone line cord(s) to the unit as follows.
Settings
To connect a two-line telephone jack
LINE 1/2LINE 2
GREEN Plug
Two-Line
Telephone Jack
(RJ14C)
4-Wire Telephone line Cord
with GREEN Plugs 

13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
If you use the unit as a single-line telephone only
To connect two single-line telephone jacks
LINE 1/2LINE 2
LINE 1/2LINE 2
GREEN
Plug
Single-Line
Telephone Jacks
(RJ11C) 4-Wire Telephone line Cord
with GREEN PlugsTRANSPARENT
Plug
2-Wire Telephone line Cord
with TRANSPARENT PlugsLINE 2
LINE 1
TRANSPARENT
PlugSingle-Line
Telephone Jack
(RJ11C)
LINE 1 2-Wire Telephone line Cord
with TRANSPARENT Plugs 

14
Settings
Battery Charge
Place the handset on the base unit and charge for about 15 hoursbefore
initial use.
•The CHARGE/LOCATOR indicator lights and a beep sounds. 
Installing the Battery in the Handset
CHARGE/LOCATOR Indicator
OR
Insert the battery into the handset as shown, matching the correct polarity
(
#). Press the battery down until it places into the compartment ($).
When finished, close the cover.
2
1 

Recharge 
Recharge
Recharge the battery when:
—“Recharge” is displayed on 
the handset,
—“ ” flashes on the display, or
—the handset beeps intermittently while it is in use.
•If you DO NOT recharge the handset battery for more than 15 minutes, the
display will continually indicate “Recharge” and/or “” will flash when the
handset is lifted off the base unit.
Battery information
After your Panasonic battery is fully charged (p. 14):
(flashing)Fully charged
Battery strengthDisplay prompt
15
Preparation
For...

Dialing Mode
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Press á.
4
Scroll to “Set dial mode” by pressing
Öor Ñ.
5
Press á.
•The current setting is displayed.
6
Select “Pulse” or “Tone” by pressing Ö
or Ñ.
7
Press á(Savekey).
•A beep sounds.
•To...

17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Your phone comes from the factory set to “A”. 
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Set line mode” by pressing
Öor Ñ.
5
Press á.
6
Press Ö(Line1) or Ñ(Line2) to select
the line.
•The line’s current setting will be...

18
Programmable Functions
You can program the following function items using the handset near
the base unit. The display shows the programming instructions. See the
corresponding pages for function details. Make sure the unit is not
being used and the handset is lifted off the base unit.
During programming:
*To select a desired function item, scroll through the items by pressing 
Öor Ñ.
Then press
áto go to the next step.
•“--------------”indicates the beginning or end of the function menu
.
•You can...

19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing  or  . If you want to use this
feature, turn the feature ON by programming. Your phone comes from the
factory set to OFF.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Auto talk” by...

20
Programmable Functions
Ringer Volume
You can select the handset ringer volume for each line. Set to HIGH,
LOW or OFF. If set to OFF, the handset will not ring for the line(s). Your
phone comes from the factory set to HIGH.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Ringer volume” by pressing
Öor Ñ.
3
Press á.
4
Press Ö(Line1) or Ñ(Line2) to 
select the line.
5
Select the desired volume by pressing 
Öor Ñ.
•Each time you...