Panasonic Kx Tg2267 Operating Instructions Manual

							11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Settings
Connecting the AC Adaptor
•USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1(Order No. KX-TCA1-G).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 60.
•If your unit is connected to a PBX which does not support Caller ID services and
voice mail services, you cannot access those services.
AC Adaptor
Raise the
antenna.Fasten the cord to prevent it
from being disconnected.
Power Outlet 
(AC 120 V, 60 Hz) Hook 
						

							12
Connecting the Telephone Line Cord
Connect the telephone line cord(s) to the unit as follows.
Settings
To connect a two-line telephone jack
LINE 1/2LINE 2
GREEN Plug
Two-Line
Telephone Jack
(RJ14C)
4-Wire Telephone line Cord
with GREEN Plugs 
						

							13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
If you use the unit as a single-line telephone only
To connect two single-line telephone jacks
LINE 1/2LINE 2
LINE 1/2LINE 2
GREEN
Plug
Single-Line
Telephone Jacks
(RJ11C) 4-Wire Telephone line Cord
with GREEN PlugsTRANSPARENT
Plug
2-Wire Telephone line Cord
with TRANSPARENT PlugsLINE 2
LINE 1
TRANSPARENT
PlugSingle-Line
Telephone Jack
(RJ11C)
LINE 1 2-Wire Telephone line Cord
with TRANSPARENT Plugs 
						

							14
Settings
Battery Charge
Place the handset on the base unit and charge for about 15 hoursbefore
initial use.
•The CHARGE/LOCATOR indicator lights and a beep sounds. 
Installing the Battery in the Handset
CHARGE/LOCATOR Indicator
OR
Insert the battery into the handset as shown, matching the correct polarity
(
#). Press the battery down until it places into the compartment ($).
When finished, close the cover.
2
1 
						

							Recharge 
Recharge
Recharge the battery when:
—“Recharge” is displayed on 
the handset,
—“ ” flashes on the display, or
—the handset beeps intermittently while it is in use.
•If you DO NOT recharge the handset battery for more than 15 minutes, the
display will continually indicate “Recharge” and/or “” will flash when the
handset is lifted off the base unit.
Battery information
After your Panasonic battery is fully charged (p. 14):
(flashing)Fully charged
Battery strengthDisplay prompt
15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Up to 11 days
OperationOperating time
While in use (TALK)Up to 5 hours
While not in use (Standby)
•The battery operating time may be shortened depending on usage conditions,
such as viewing the Caller ID Caller List or directory list, and ambient
temperature.
•Clean the handset and the base unit charge contacts with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or
high humidity.Otherwise the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the base
unit until “Recharge” is displayed and/or “” flashes. This will maximize the
battery life.
•The battery cannot be overcharged.
Needs to be recharged.
Battery strength
You can check the battery strength on the handset display.
The battery strength is as shown in the chart below.
Medium
Low 
						

							Dialing Mode
If you have touch tone service, set to “Tone”. If rotary or pulse service is
used, set to “Pulse”. Your phone comes from the factory set to “Tone”.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Press á.
4
Scroll to “Set dial mode” by pressing
Öor Ñ.
5
Press á.
•The current setting is displayed.
6
Select “Pulse” or “Tone” by pressing Ö
or Ñ.
7
Press á(Savekey).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
.
16
--------------
HSave directory
Ringer volume
Ringer tone
HProgram
--------------
--------------
HSet flash time
Save VM acces#
Set line mode
HSet dial mode
Line selection
Dial mode
:Tone
GF H=Save
Dial mode
:Pulse
Dial mode
:Pulse
GF H=Save
Settings 
						

							17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”.
Your phone comes from the factory set to “A”. 
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Set line mode” by pressing
Öor Ñ.
5
Press á.
6
Press Ö(Line1) or Ñ(Line2) to select
the line.
•The line’s current setting will be displayed.
7
Select “B” or “A” by pressing Öor Ñ.
8
Press á(Savekey).
•A beep sounds.
•To program the other line, start again from step 4.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
. Line mode
G=Line1 F=Line2
Line mode
Line1:B
Line mode
Line1:A
GF H=Save
--------------
HSave directory
Ringer volume
Ringer tone
HProgram
--------------
--------------
HSet flash time
Save VM acces#
VM tone detect
HSet line mode
Set dial mode
Line mode
Line1:B
GF H=Save 
						

							18
Programmable Functions
You can program the following function items using the handset near
the base unit. The display shows the programming instructions. See the
corresponding pages for function details. Make sure the unit is not
being used and the handset is lifted off the base unit.
During programming:
*To select a desired function item, scroll through the items by pressing 
Öor Ñ.
Then press
áto go to the next step.
•“--------------”indicates the beginning or end of the function menu
.
•You can exit the programming mode any time by pressing (OFF).
•If you do not press any buttons for 60 seconds, the unit will exit the programming
mode.
•If the handset has lost communication with the base unit, 3 beeps sound and “No
link to base Place on cradle and try again.” is displayed.
Press (HOLD/FUNCTION/CLEAR).
*
To store an item in the directory (p. 37).
To select the ringer volume (p. 20).
To select the ringer tone (p. 21).
Press 
á. --------------
HSave directory
Ringer volume
Ringer tone
Program
--------------
--------------
HSet flash time
Save VM acces#
VM tone detect
Set line mode
Set dial mode
Line selection
Incoming call.
Auto talk
CallerID edit
LCD contrast
--------------To select the flash time (p. 53).
To store a voice mail access number (p. 44).
To set the voice mail tone detection(p. 46).
To select the line mode (p. 17).
To select the dialing mode (p. 16).
To change the line selection (p. 54).
To set the incoming call tone (p. 55).
To set the Auto Talk feature (p. 19).
To set the Caller ID Number Auto Edit feature (p. 33).
To select the LCD contrast (p. 22). * 
						

							19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Auto Talk Feature
The Auto Talk feature allows you to answer a call by lifting the handset off
the base unit without pressing  or  . If you want to use this
feature, turn the feature ON by programming. Your phone comes from the
factory set to OFF.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Program” by pressing Öor Ñ.
3
Pressá.
4
Scroll to “Auto talk” by pressing Öor
Ñ.
5
Press á.
•The current setting is displayed.
6
Select “On” or “Off” by pressing Öor Ñ.
7
Press á(Savekey).
•A beep sounds.
•To exit the programming mode, press (OFF).
•You can exit the programming mode any time by pressing (OFF)
.
•In order to view Caller ID information after you lift up the handset to answer a
call, leave the Auto Talk feature OFF.
Auto talk
:On
Incoming call.
HAuto talk
CallerID edit
Auto talk
:Off
GF H=Save
Auto talk
:On
GF H=Save
Ringer tone
HProgram
-------------- 
						

							20
Programmable Functions
Ringer Volume
You can select the handset ringer volume for each line. Set to HIGH,
LOW or OFF. If set to OFF, the handset will not ring for the line(s). Your
phone comes from the factory set to HIGH.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (HOLD/FUNCTION/CLEAR).
2
Scroll to “Ringer volume” by pressing
Öor Ñ.
3
Press á.
4
Press Ö(Line1) or Ñ(Line2) to 
select the line.
5
Select the desired volume by pressing 
Öor Ñ.
•Each time you press Öor Ñ, the volume
will change and ring.
•If you set to OFF, the unit will not ring.
6
Press á(Savekey).
•A beep sounds.
•You can exit the programming mode any time by pressing (OFF)
.
•When you replace the battery, the selected ringer volume setting will return to the
factory set (HIGH). Reprogram if necessary.
Ringer    Line1
Low❚❚❚❚❚❚High
GF H=Save
Ringer    Line1
Low❚❚❚❚❚❚High
GF H=Save
HIGH
LOW
Ringer off L1
GF H=Save
OFF
Ö
Ñ
Ö
Ñ
Save directory
HRinger volume
Ringer tone
Ringer volume
G=Line1 F=Line2