Panasonic Kx Tg2227 Operating Instructions Manual

							41
Answering System
Direct commands
For assistance, please call: 1-800-211-PANA(7262)
NEW MESSAGE
PLAYBACK
ALL MESSAGE
PLAYBACK
REPEAT 
(During playback)
SKIP
(During playback)
CHANGING
PLAYBACK
SPEED
(During playback)
STOP
ERASING A
SPECIFIC
MESSAGE
(During playback)
ERASING ALL
MESSAGES
ANSWERING
SYSTEM OFF
ANSWERING
SYSTEM ON(4)
(5)
(1)
(2)
(9)
(*) (4)
(*) (5)•Only new messages are played back.
•All messages are played back.
•The current message is repeated.
•If you press within 5 seconds of
playback, the previous message will be
played.
•The current message is skipped.
The next message is played.
•Each time you press the button, the
playback speed will change to
slow/normal.
•Operation is stopped temporarily.
•To resume operation, enter a direct
command within 15 seconds, or the
voice menu will start (p. 40).
•The current message is erased.
•A short beep will sound and the next
message will be played.
•All recorded messages are erased.
•A long beep sounds and “No messages” is
heard.
•“Answer off” is heard and the answering
system is turned off.
•“Answer set” is heard and the answering
system is turned on.
(0)
(8)
(3) 
						

							42
Wall Mounting
This unit can be mounted on a wall phone plate.
2
Connect the AC adaptor.
3
Tuck the telephone line cord inside
the wall mounting adaptor, then
push it in the direction of the arrow.
•The word “UP” should face upward.
1
Push the hook and turn it around.
Turn the hook until a click is heard.
To Power
Outlet 
						

							43
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
•Fasten the telephone line cord to
prevent it from being disconnected.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The IN USE/CHARGE/HOLD indicator
lights.
2
1
Hook
Hole
Hooks
OR 
						

							44
H
You can hang the handset on your belt or pocket using the belt clip.
To attach the belt clip To remove the belt clip
Headset Jack
Connecting an optional headset to the handset
Open the headset jack cover, and connect an optional headset to the
headset jack as shown below.
Belt Clip
Plugging an optional headset into the handset allows a hands-free phone
conversation. Please use only a Panasonic KX-TCA88 or KX-TCA90
headset. To order, call the accessories telephone number on page 2.
Optional Headset
The illustration headset
is a KX-TCA88.
To switch to the speakerphone while using the headset:
Press  . To return to the headset, press  . 
						

							45
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery. If the RECHARGE indicator flashes after being fully charged, replace the
battery with a new Panasonic P-P511 (PQPP511SVC) battery. To order,
call the accessories telephone number on page 2.
1
Press the notch on the
handset cover firmly and
slide it as indicated by the
arrow.
2
Remove the old battery.
Insert the new battery into
the handset as shown (#),
matching the correct polarity.
Press the battery down 
until it places into the
compartment ($).
3
Close the cover. Make sure you charge the new battery for about
15 hours (p. 10).
2
1 
						

							46
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord 
						

							47
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
An alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The unit does not ring.
You cannot store a phone
number in memory.
While storing a phone
number, the unit starts to
ring.
You cannot make a call with
the handset.
You cannot page the
handset.
Remedy
•You are too far from the base unit. Move
closer and try again.
•Place the handset on the base unit and
try again.
•Plug in the AC adaptor.
•Raise the base unit antenna.
•Locate the handset and the base unit
away from other electrical appliances
(p. 3).
•Move closer to the base unit.
•Raise the base unit antenna.
•Press 
Üto select a clearer channel in
the talk, speakerphone, intercom or
remote operation mode.
•The ringer volume is set to OFF. Set to
HIGH or LOW (p. 14).
•You cannot store a number while the
unit is in the talk or intercom mode.
•Do not pause for over 60 seconds while
storing.
•To answer the call, press, .
Start again from the beginning after
hanging up.
•You cannot make a call when the unit is
in the remote operation mode. Exit the
mode by pressing 
(OFF)(p. 40).
•The handset is too far from the base unit.
•The handset is engaged in an outside
call or listening to messages. Wait until
the IN USE/CHARGE/HOLD indicator
light goes out.
Cordless Telephone
Troubleshooting 
						

							48
Troubleshooting
Problem
You cannot redial by
pressing 
(REDIAL/PAUSE).
You cannot have a
conversation using the
headset.
Remedy
•If the last number dialed was more than
32 digits long, the number will not be
redialed correctly.
•The button has a double function as
either redial or pause. It will redial the
last number dialed if pressed at the
outset of a call (p. 22). If another
number has been dialed first, it will
operate as a pause button (p. 27).
•Make sure that an optional headset is
connected properly (p. 44).
•may have been pressed, press
to continue the conversation with
the headset. 
						

							49
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
The answering system is on,
but incoming messages are
not recorded.
You cannot listen to the
recorded messages.
“” is displayed and the
ANSWER ON indicator
flashes rapidly, and no new
messages are recorded.
You cannot operate the
answering system with the
base unit.
You cannot operate the
answering system from a
touch tone phone.
You cannot operate the
answering system with the
handset.
FULL
Remedy
•The recording time is set to “Greeting
only”. Select “1 minute”, “2 minutes” or 
“3 minutes” (p. 19).
•Memory is full. Erase some, or all, of
the messages (p. 32).
•Make sure that the unit is not being
used.
•Memory is full. Erase some, or all, of
the messages (p. 32).
•The handset user is operating the
answering system, or is engaged in an
outside call. Wait until the 
IN USE/CHARGE/HOLD indicator light
goes out.
•Make sure you enter the correct
remote code.
•The answering system may not
respond if the tones are too short to
activate the unit. Press each button
firmly.
•The answering system is off. Turn it
on (p. 39).
•Someone is operating the answering
system.
•You are too far from the base unit. 
Move closer to the base unit.
•The unit is recording a message. 
To answer the call, press or .
Answering System 
						

							50General
Troubleshooting
Problem
While recording a greeting
message, the unit starts to
ring and stops recording.
During playback, the unit
starts to ring and stops
playback.
Remedy
•To answer the call, lift the handset off
the base unit or press
, or .
Start again from the beginning after
hanging up.
•To answer the call, lift the handset off
the base unit or press
, or . 
To resume playback, press
(MESSAGE!PLAYBACK/SLOW!TALK)
after hanging up.
Problem
The unit does not work.
Remedy
•Check the settings (p. 9–14).
•Charge the battery fully (p. 10).
•Clean the charge contacts and charge
again (p. 11).
•Install the battery properly (p. 10).
•Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.
•Re-install the battery and place the
handset on the base unit (p. 45). Try
again.