Panasonic Kx Tg2000 Operating Instructions Manual

11
Displays
Chapter 1PreparationBase unit
Cordless handset
BAuto Attendant Icon
AVoice Mail Icon
BLine Status Icon
CBattery Icon
D
AThe handset in-use icon indicates the status of registered cordless
handsets. If a cordless handset is in the talk or intercom mode, or
listening to messages, the relevant number is displayed.
BIf you turn the Automated Attendant System on, the relevant line icon is
displayed (p. 59).
CThe time and date are displayed on the first line in the standby mode.
The display shows...

12
Installation
•The battery cannot be overcharged.
•If the backup battery has been discharged during a power failure, the unit will not
work. If required, you can connect a standard telephone on the same line. See
page 91.BATTERY Indicator:
•The BATTERY indicator lights while
the battery is being charged. (This is
normal.)
•During a power failure (or if the AC
adaptor is disconnected), the
BATTERY indicator shows the
battery strength:
Full to Medium: The indicator lights.
Low: The indicator flashes.
No...

13
Chapter 1Preparation
•Use only a Panasonic Handset for the KX-TG2000B.
•USE ONLY WITH Panasonic AC ADAPTOR PQLV12 (Order No. PQLV12Z). 
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•The BATTERY indicator lights while the AC adaptor is connected with the backup
battery installed (p. 12). (This is normal.)
Connecting the Handset and AC Adaptor
Handset
Handset
Cord
Power Outlet
(AC 120 V, 60 Hz)
AC Adaptor
PQLV12
Fasten the AC adaptor cord to...

14
Installation
Connecting the Telephone Line Cord(s)
Connect the telephone line cord(s) to the base unit.
To connect a two-line telephone jack
Two-Line Telephone
Jack (RJ14C)4-Wire Telephone
Line Cord with
GREEN PlugsLINE 2 LINE 1/2
GREEN Plug 

LINE 2 LINE 1/2
TRANSPARENT
Plug GREEN
Plug
15
Chapter 1PreparationTo connect two single-line telephone jacks
Single-Line
Telephone Jacks
(RJ11C) LINE2
LINE1
4-Wire Telephone
Line Cord with
GREEN Plugs
2-Wire Telephone Line
Cord with
TRANSPARENT Plugs
If you use the unit as a single-line telephone only
LINE 2 LINE 1/2
TRANSPARENT Plug
Single-Line
Telephone Jack
(RJ11C)2-Wire Telephone
Line Cord with
TRANSPARENT
Plugs
•With this connection, you can only use LINE 1. LINE1 

16
Installation
Connecting the AC Adaptor to the Charger
•USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G). 
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
Handset Battery Charge   
Place the cordless handset on the charger and
charge for about 8 hoursbefore initial use.
Make sure the handset faces forward as
shown.
•The CHARGE indicator lights.
•If you charge the discharged battery, it will be
charged quickly. In that case the...

Up to about 4 days
(flashing)
17
Chapter 1Preparation
Approx. battery life
•Battery life may be shortened depending on usage conditions and ambient
temperature.
•Clean the charge contacts of the handset and the charger with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease, dust or
high humidity.Otherwise the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the charger
until “Recharge” is displayed and/or “”...

18
Programmable Settings
Programming Guidelines 
This unit has various programmable functions. Most of them are selected
from the function menu on the display (p. 24).
Base UnitHandset
How to select a function item from the menu
1. Press (FUNCTION)while in the standby mode. The main menu is
displayed.
2. You can scroll through the menu by
pressing  or  . Find the desired
item and point the arrow to the item
by pressing  or  .
3. Press Hto select the item.
4. If the selected item has a sub-menu, it will...

19
Chapter 1PreparationRegistration for Additional Cordless Handsets 
The included cordless handset is pre-registered at the factory and
assigned the handset number 1. Do not try to register the handset
number 1 which has “[1]” on the display. Optional handsets must be
registered at the base unit. You can add up to 7 optional handsets to the
handset number 1. Only one handset can be registered at a time. The
handset number is used as the extension number (p. 32, 58). 
The model number of the optional...

20
4Select AM or PM by pressing  .
5Press (ENTER).
•A beep sounds. The clock starts
working.
•To return to the standby mode,
press 
(EXIT).
1Press (FUNCTION).
2Press  or  until the arrow
points to “Date and time”,
and press H.
3#Enter the year, and month and
day using 4-digit numbers.
Ex. To set Apr. 7, 2000, enter
“2000”and “0407”.
$Enter the time (hour and
minute) using a 4-digit
number.
Ex. To set 9:30, enter “0930”.
Date and Time Adjustment 
Make sure that the base unit is in the standby mode. 
Base...