Panasonic Kx-Td816e, Kx-td1232e User Manual

DPT Overview1-23
1.1Configuration
Volume Control — Handset Receiver/Headset/Ringer/Speaker
Allows you to adjust the following volumes as necessary:
— Handset Receiver volume (level 1 through 3)
— Headset volume (level 1 through 3)
— Ringer volume (level 0 through 3)
— Speaker volume (level 1 through 12)
If your digital proprietary telephone is provided with a display (display DPT),the volume
level is indicated on the display.  For ringer volume adjustment,three levels
(OFF/LOW/HIGH) are available with...

1-24DPT Overview
1.1Configuration
While the telephone is idle and on-hook;
1.Press the RING(S2) button.
•The telephone will ring.
2.Press the VOLUME(UP / DOWN ) Control button.
•The telephone will stop ringing in about 4 seconds.
•When the volume level is 0,the display shows ”RNGOFF.”
– KX-T7220 and KX-T7250
1.Adjust the RINGER Volume Selector lever to the desired
setting(OFF/LOW/HIGH).
To adjust the speaker volume
1.Press the SP-PHONE orMONITOR button.
2.Press the VOLUME(UP / DOWN ) Control button.
•The...

DPT Overview1-25
1.1Configuration
BLF on DSS Button
The Busy Lamp Field (BLF) indicates the status of corresponding extension by lighting
patterns:Red On/Off.  BLF lights red when the corresponding extension is busy,is set the
“Do Not Disturb (DND)”feature,or while in the check-in mode of the “Hotel Application.”
And BLF lights off when it is idle.  This is available for DSS buttons of DSS consoles and
for flexible CO buttons assigned as DSS buttons on proprietary telephones.
LED Indication
The Light...

Section 2
Station Programming
Contents
2.1 Station Programming Instructions .....................................
2-2
2.2 Station Programming (A - Z) ..............................................2-6

All illustrations used in these operating instructions are based on the 
KX-T7235 model. 

2-2Station Programming
2.1Station Programming Instructions
Station Programming allows you,the proprietary telephone (PT) user,to program certain
features from your telephone individually.  To program,you need to switch your
telephone to the Station Programming mode.  And during the programming mode,your
telephone is put in a busy condition to outside caller.  If you want to make a normal call
handling operation,you should finish the programming mode.
Programming Mode Display
When you enter the Station...

Station Programming2-3
2.1Station Programming Instructions
To confirm the assigned function data
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Enter the programming access number* (0 through 9,01
through 03,1 and #).
•Each number corresponds to the data as follows:
-1:Preferred Line Assignment — Outgoing
-2:Preferred Line Assignment — Incoming
-3:Full One-Touch Dialling Assignment
-4:Intercom Alerting Assignment
-5:Call Waiting Tone Type Assignment
-6:Self-Extension...

2-4Station Programming
2.1Station Programming Instructions
To confirm the assigned data on the Flexible button
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS,PF) button.
•The display shows the current status.
2.Press the HOLD(END) button.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
—If you wish to change the data,follow the programming procedure explained in...

Station Programming2-5
2.1Station Programming Instructions
Station Programming OutlineDirect Station Selection (DSS) Button
One-Touch Dialling Button
Message Waiting (MESSAGE) Button
FWD/DND Button
SAVE Button
Account Button
Conference (CONF) Button
Log-In / Log-Out Button
Hurry-Up Button
Voice Mail (VM) Transfer Button
Two-Way Record Button†
Two-Way Transfer Button†
Live Call Screening (LCS) Button†
Live Call Screening (LCS) Cancel Button†
Alert Button
Phantom Extension Button
Night Button
One-Touch...

2-6Station Programming
2.2Station Programming
Call Waiting Tone Type Assignment
Allows you to select the call waiting tone type (Tone 1 or Tone 2).
— Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 5.
•The display shows the current tone type.
2.Dial 1or 2.
-1 :for selecting Call Waiting Tone 1
-2 :for selecting Call Waiting Tone 2
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station...