Panasonic Kx Taw848 Feature Manual

1.9 Automatic Route Selection (ARS) Features
Feature Guide 81
[Command Explanation]
[Programming Example: Carrier Table]
6.ARS Options
Authorization Code for Tenant
A Carrier Authorization Code can be assigned to each tenant.
Authorization Code for CO Line Group
A Carrier Authorization Code can be assigned to each CO line group.
Itemized Billing Code
An Itemized Billing Code can be assigned for each extension and for each verified code.
If a call is not made from an extension, such as via Direct Inward...

1.9 Automatic Route Selection (ARS) Features
82 Feature Guide
Conditions
WARNINGThe software contained in the ARS feature to allow user access to the network must be 
upgraded to recognize newly established network area codes and exchange codes as 
they are placed into service.
Failure to upgrade the premises PBXs or peripheral equipment to recognize the new 
codes as they are established will restrict the customer and the customer’s employees 
from gaining access to the network and to these codes.
KEEP...

1.10 Conversation Features
Feature Guide 83
1.10 Conversation Features
1.10.1 Hands-free Operation
Description
A proprietary telephone (PT) user can talk to another party without lifting the handset. Pressing 
specific buttons, such as REDIAL, automatically activate hands-free mode.
Conditions
PTs with the MONITOR Button
PTs with the MONITOR button can dial in hands-free mode but cannot have hands-free 
conversations.
1.10.2 Mute
Description
During a conversation, a proprietary telephone (PT) user can...

1.10 Conversation Features
84 Feature Guide
Answer/Release Button
A flexible button can be customized as an Answer button or a Release button. Such 
buttons are useful for headset operation. It is possible to answer an incoming call by 
pressing the Answer button. While hearing a call waiting tone during a conversation, 
pressing the Answer button enables one to answer the second call by placing the current 
call on hold. Pressing the Release button enables one to disconnect the line during or after...

1.10 Conversation Features
Feature Guide 85
Conditions
FLASH/RECALL Button Mode 
One of the following modes can be selected for each extension through system 
programming: 
Terminate Button
Any flexible button can be customized as the Terminate button.
Disconnect Time (Only for Flash/Recall Mode)
The amount of time between successive accesses to the same CO line is programmable 
for each CO line port (  LCOT Disconnect Time [418]).
This feature generates a Station Message Detail Recording (SMDR) call...

1.10 Conversation Features
86 Feature Guide
User Manual References
User Manual
1.9.2 Host PBX
1.10.7 CO Line Call Limitation
Description
CO Line calls are limited by the following features:
Conditions
During an Unattended Conference Call, the Unattended Conference Recall time is 
applied. (  1.13.1.2 Conference)Feature Description
Extension-to-CO Line 
Call DurationIf a call between an extension user and an outside party is 
established, the call duration can be restricted by the system 
timer selected...

1.10 Conversation Features
Feature Guide 87
1.10.8 Paralleled Telephone
Description
By connecting telephones in parallel, you can increase the number of telephones connected 
to the PBX without adding additional extension cards.
Both wired and wireless telephones can be connected in parallel. Single line telephones (SLTs) 
and analog proprietary telephones (APTs) can be connected to other telephones or 
connectors, allowing two telephones to be connected to the PBX through just one extension 
port....

1.10 Conversation Features
88 Feature Guide
Installation Manual References
Installation Manual
2.6.2 Parallel Connection of the Extensions
1.10.9 Calling Party Control (CPC) Signal Detection
Description
The Calling Party Control (CPC) signal is an on-hook indication (disconnect signal) sent from 
a CO line when the other party hangs up. To maintain efficient utilization of CO lines, the PBX 
monitors each line’s status and when CPC signal is detected on a line, the PBX disconnects 
the line and alerts...

1.11 Transferring Features
Feature Guide 89
1.11 Transferring Features
1.11.1 Call Transfer
Description
An extension user can transfer a call to another extension or an outside party. The following 
features are available:
Call Transfer with Announcement is also known as Call Transfer—Screened.
Call Transfer without Announcement is also known as Call Transfer—Unscreened.
Conditions
If Music on Hold is enabled, music can be sent to the held party while the call is being 
transferred. (  1.12.4 Music on...

1.11 Transferring Features
90 Feature Guide
One-touch Transfer
DSS Console users and the proprietary telephone (PT) users can hold a call and quickly 
transfer it to an extension by pressing the DSS button directly. A One-touch Dialing button 
can also be used if the TRANSFER command is stored with an extension number or a 
telephone number (  1.6.1 Memory Dialing Features).
Consultation Hold
When an extension user performs a Call Transfer, the call is placed automatically on 
consultation hold (...