Panasonic Kx Ta824 Programming Manual
Have a look at the manual Panasonic Kx Ta824 Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 46
2.2 PT Programming—Procedures
46 Programming Manual
[423] CO Line Ring Tone Pattern
Selects the ring tone pattern for incoming outside (CO) line calls.
Conditions
It is recommended that you set a different ring tone pattern from the ring tone patterns specified in
[115] Extension Ring Tone Pattern and [706] Doorphone Ring Tone Pattern.
Programming Manual References
[115] Extension Ring Tone Pattern
[706] Doorphone Ring Tone Pattern
Feature Manual References
1.1.108 Ring Tone Pattern Selection
[435]...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-45.png "Page 46
2.2 PT Programming—Procedures
46 Programming Manual
[423] CO Line Ring Tone Pattern
Selects the ring tone pattern for incoming outside (CO) line calls.
Conditions
It is recommended that you set a different ring tone pattern from the ring tone patterns specified in
[115] Extension Ring Tone Pattern and [706] Doorphone Ring Tone Pattern.
Programming Manual References
[115] Extension Ring Tone Pattern
[706] Doorphone Ring Tone Pattern
Feature Manual References
1.1.108 Ring Tone Pattern Selection
[435]...")
![Page 47
2.2 PT Programming—Procedures
Programming Manual 47
[436] Local Carrier-based Voice Mail Access Dial
Specifies the voice mail service access number. This program allows a PT user to access the telephone
companys voice mail service when a message is left in the mailbox.
Feature Manual References
1.1.78 Local Carrier-based Voice Mail Service
[437] Extension Access to Local Carrier-based Voice Mail
Selects which extensions can access the voice mail service offered by the telephone company using each...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-46.png "Page 47
2.2 PT Programming—Procedures
Programming Manual 47
[436] Local Carrier-based Voice Mail Access Dial
Specifies the voice mail service access number. This program allows a PT user to access the telephone
companys voice mail service when a message is left in the mailbox.
Feature Manual References
1.1.78 Local Carrier-based Voice Mail Service
[437] Extension Access to Local Carrier-based Voice Mail
Selects which extensions can access the voice mail service offered by the telephone company using each...")
![Page 48
2.2 PT Programming—Procedures
48 Programming Manual
[438-440] DISA IRNA to BV—Day/Night/Lunch
Selects the common BV OGM used as the intercept destination of unanswered DISA calls in each time
service mode.
Feature Manual References
1.1.8 Built-in Voice Message (BV)
[500] DISA Incoming Call Dial Mode
Selects the destination of an incoming outside (CO) line call via the DISA feature.
Notes
Without AA: Available destinations are extension numbers assigned in [009] Extension Number,
Outside (CO) Line...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-47.png "Page 48
2.2 PT Programming—Procedures
48 Programming Manual
[438-440] DISA IRNA to BV—Day/Night/Lunch
Selects the common BV OGM used as the intercept destination of unanswered DISA calls in each time
service mode.
Feature Manual References
1.1.8 Built-in Voice Message (BV)
[500] DISA Incoming Call Dial Mode
Selects the destination of an incoming outside (CO) line call via the DISA feature.
Notes
Without AA: Available destinations are extension numbers assigned in [009] Extension Number,
Outside (CO) Line...")
![Page 49
2.2 PT Programming—Procedures
Programming Manual 49
Conditions
This program is available only when With AA is selected in [500] DISA Incoming Call Dial Mode.
If you would like to use the Automatic Line Access number and/or Operator Call number in AA
mode, do not assign AA number(s) that correspond to Automatic Line Access or Operator Call
numbers (9 and/or 0).
Programming Manual References
[500] DISA Incoming Call Dial Mode
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[503]...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-48.png "Page 49
2.2 PT Programming—Procedures
Programming Manual 49
Conditions
This program is available only when With AA is selected in [500] DISA Incoming Call Dial Mode.
If you would like to use the Automatic Line Access number and/or Operator Call number in AA
mode, do not assign AA number(s) that correspond to Automatic Line Access or Operator Call
numbers (9 and/or 0).
Programming Manual References
[500] DISA Incoming Call Dial Mode
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[503]...")
![Page 50
2.2 PT Programming—Procedures
50 Programming Manual
[510] DISA No Dial Mode
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[506] DISA Busy Mode
Selects how DISA calls are handled when a called extension is busy.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.88 Outgoing Message (OGM) for DISA
[507] DISA Intercept Mode
Selects how DISA calls are handled when the destination does not answer the call within a preprogrammed
time period.
Feature Manual...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-49.png "Page 50
2.2 PT Programming—Procedures
50 Programming Manual
[510] DISA No Dial Mode
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[506] DISA Busy Mode
Selects how DISA calls are handled when a called extension is busy.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.88 Outgoing Message (OGM) for DISA
[507] DISA Intercept Mode
Selects how DISA calls are handled when the destination does not answer the call within a preprogrammed
time period.
Feature Manual...")
![Page 51
2.2 PT Programming—Procedures
Programming Manual 51
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.68 Intercept Routing
[509] DISA Ring Time after Intercept
Selects the length of time to ring the destination extension when a DISA call is redirected to the intercept
destination after the time specified in [508] DISA Ring Time before Intercept expires. When the destination
extension does not answer the call within the preprogrammed time period, the call is disconnected....](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-50.png "Page 51
2.2 PT Programming—Procedures
Programming Manual 51
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.68 Intercept Routing
[509] DISA Ring Time after Intercept
Selects the length of time to ring the destination extension when a DISA call is redirected to the intercept
destination after the time specified in [508] DISA Ring Time before Intercept expires. When the destination
extension does not answer the call within the preprogrammed time period, the call is disconnected....")
![Page 52
2.2 PT Programming—Procedures
52 Programming Manual
Programming Manual References
[512] DISA Security Code
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[512] DISA Security Code
Specifies the DISA security codes that must be entered when Trunk Security (a DISA security code is
required to make an outside (CO) line call) or All Security (a DISA security code is required to make an
intercom call or outside (CO) line call) is selected in [511] DISA Security Mode.
WARNING
There is a...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-51.png "Page 52
2.2 PT Programming—Procedures
52 Programming Manual
Programming Manual References
[512] DISA Security Code
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[512] DISA Security Code
Specifies the DISA security codes that must be entered when Trunk Security (a DISA security code is
required to make an outside (CO) line call) or All Security (a DISA security code is required to make an
intercom call or outside (CO) line call) is selected in [511] DISA Security Mode.
WARNING
There is a...")
![Page 53
2.2 PT Programming—Procedures
Programming Manual 53
[513] Cyclic Tone Detection
Selects the number of times the cyclic tone must be detected while the DISA OGM is sent so that the PBX
can recognize the end of the DISA call.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[514] FAX Tone Detection
Selects the number of times the fax (CNG) tone must be detected while the DISA OGM is sent before the
PBX recognizes the incoming signal as fax data.
Programming Manual References
[503] FAX...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-52.png "Page 53
2.2 PT Programming—Procedures
Programming Manual 53
[513] Cyclic Tone Detection
Selects the number of times the cyclic tone must be detected while the DISA OGM is sent so that the PBX
can recognize the end of the DISA call.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[514] FAX Tone Detection
Selects the number of times the fax (CNG) tone must be detected while the DISA OGM is sent before the
PBX recognizes the incoming signal as fax data.
Programming Manual References
[503] FAX...")
![Page 54
2.2 PT Programming—Procedures
54 Programming Manual
[516] DISA Incoming Assignment
Enables receiving calls from DISA for each extension.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[517] DISA AA Wait Time
Specifies the length of time after entering a first digit in which the caller must dial the second digit before the
DISA AA Service activates.
Conditions
This program is available only when With AA is selected in [500] DISA Incoming Call Dial Mode.
Programming Manual...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-53.png "Page 54
2.2 PT Programming—Procedures
54 Programming Manual
[516] DISA Incoming Assignment
Enables receiving calls from DISA for each extension.
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[517] DISA AA Wait Time
Specifies the length of time after entering a first digit in which the caller must dial the second digit before the
DISA AA Service activates.
Conditions
This program is available only when With AA is selected in [500] DISA Incoming Call Dial Mode.
Programming Manual...")
![Page 55
2.2 PT Programming—Procedures
Programming Manual 55
[530] DISA Security Code Digits
Selects the number of digits for the DISA security codes.
Conditions
When this setting is changed, DISA security codes that have already been assigned in [512] DISA
Security Code will be cleared.
Programming Manual References
[512] DISA Security Code
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[531] DISA Ringback Tone
Selects whether to send a ringback tone or Music on Hold to the caller when a...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-54.png "Page 55
2.2 PT Programming—Procedures
Programming Manual 55
[530] DISA Security Code Digits
Selects the number of digits for the DISA security codes.
Conditions
When this setting is changed, DISA security codes that have already been assigned in [512] DISA
Security Code will be cleared.
Programming Manual References
[512] DISA Security Code
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[531] DISA Ringback Tone
Selects whether to send a ringback tone or Music on Hold to the caller when a...")
![Page 56
2.2 PT Programming—Procedures
56 Programming Manual
Programming Manual References
[501] DISA Built-in AA
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[599] Clear All OGMs of DISA
Clears all the prerecorded messages (DISA OGMs).
Feature Manual References
1.1.88 Outgoing Message (OGM) for DISA
[600] Extension Group
Selects the extension group to which the extension belongs.
Feature Manual References
1.1.21 Call Pickup, Group
1.1.42 Direct Inward System Access (DISA) Ring
1.1.53...](http://img.usermanuals.tech/thumb/58/64571/w64_kx-ta824_en_program_om_d-55.png "Page 56
2.2 PT Programming—Procedures
56 Programming Manual
Programming Manual References
[501] DISA Built-in AA
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
[599] Clear All OGMs of DISA
Clears all the prerecorded messages (DISA OGMs).
Feature Manual References
1.1.88 Outgoing Message (OGM) for DISA
[600] Extension Group
Selects the extension group to which the extension belongs.
Feature Manual References
1.1.21 Call Pickup, Group
1.1.42 Direct Inward System Access (DISA) Ring
1.1.53...")
2.2 PT Programming—Procedures Programming Manual 51 Feature Manual References 1.1.41 Direct Inward System Access (DISA) 1.1.68 Intercept Routing [509] DISA Ring Time after Intercept Selects the length of time to ring the destination extension when a DISA call is redirected to the intercept destination after the time specified in [508] DISA Ring Time before Intercept expires. When the destination extension does not answer the call within the preprogrammed time period, the call is disconnected. Programming Manual References [507] DISA Intercept Mode [508] DISA Ring Time before Intercept Feature Manual References 1.1.41 Direct Inward System Access (DISA) 1.1.68 Intercept Routing [510] DISA No Dial Mode Selects how DISA calls are handled when the PBX does not receive either DTMF (Dual Tone Multi- Frequency) signals or a fax (CNG) tone within a preprogrammed time period. Feature Manual References 1.1.41 Direct Inward System Access (DISA) [511] DISA Security Mode Selects the DISA security mode to prevent unauthorized access to the PBX. In Trunk or All security mode, the caller is required to enter a DISA security code. Notes Trunk Security: Requires the caller to enter a DISA security code assigned in [512] DISA Security Code before making an outside (CO) line call. All Security: Requires the caller to enter a DISA security code before making either an outside (CO) line or intercom call. No Security: Allows the caller to make either an outside (CO) line or intercom call without entering a DISA security code. 509NEXTSELECTSTOREEND (10/ 20/30/ 40/60/120 s) 510NEXTSTOREENDSELECT ( Intercept/ Disconnect) 511NEXTSELECTSTOREEND ( Trunk/All/ None Security)
2.2 PT Programming—Procedures 52 Programming Manual Programming Manual References [512] DISA Security Code Feature Manual References 1.1.41 Direct Inward System Access (DISA) [512] DISA Security Code Specifies the DISA security codes that must be entered when Trunk Security (a DISA security code is required to make an outside (CO) line call) or All Security (a DISA security code is required to make an intercom call or outside (CO) line call) is selected in [511] DISA Security Mode. WARNING There is a risk that fraudulent telephone calls will be made using the Outside-to-Outside (CO-to-CO) Line Call feature of DISA. The cost of such calls will be billed to the owner/renter of the PBX. To protect the PBX from this kind of fraudulent use, we strongly recommend: a)Enabling DISA security (Trunk Security or All Security). b)Maintaining the secrecy of passwords. c)Selecting passwords that are complex and random, so that they cannot be easily guessed. d)Changing passwords regularly. Conditions This setting is required if Trunk Security or All Security is selected in [511] DISA Security Mode. Each DISA security code should be unique. The number of digits for DISA security codes is selected in [530] DISA Security Code Digits. Programming Manual References [511] DISA Security Mode [530] DISA Security Code Digits Feature Manual References 1.1.41 Direct Inward System Access (DISA) 51 2NEXTcode no.security codeSTOREEND (1… 4) 4… 10 digits (0… 9) SELECT NEXTPREVor To continue To continue All-Not stored
2.2 PT Programming—Procedures Programming Manual 53 [513] Cyclic Tone Detection Selects the number of times the cyclic tone must be detected while the DISA OGM is sent so that the PBX can recognize the end of the DISA call. Feature Manual References 1.1.41 Direct Inward System Access (DISA) [514] FAX Tone Detection Selects the number of times the fax (CNG) tone must be detected while the DISA OGM is sent before the PBX recognizes the incoming signal as fax data. Programming Manual References [503] FAX Connection Feature Manual References 1.1.41 Direct Inward System Access (DISA) [515] Intercept Time for Internal DISA Selects the length of time the PBX keeps detecting DTMF signals after receiving a call using DISA when no DISA OGM is recorded. Programming Manual References [408-410] Flexible Ringing—Day/Night/Lunch [438-440] DISA IRNA to BV—Day/Night/Lunch [510] DISA No Dial Mode Feature Manual References 1.1.41 Direct Inward System Access (DISA) 513NEXTSELECTSTOREEND (Disable/ 2/3/ 4 times) 514NEXTSELECTSTOREEND ( 1/2 time(s)) 515NEXTSELECTSTOREEND ( 3/6/9 s)
2.2 PT Programming—Procedures 54 Programming Manual [516] DISA Incoming Assignment Enables receiving calls from DISA for each extension. Feature Manual References 1.1.41 Direct Inward System Access (DISA) [517] DISA AA Wait Time Specifies the length of time after entering a first digit in which the caller must dial the second digit before the DISA AA Service activates. Conditions This program is available only when With AA is selected in [500] DISA Incoming Call Dial Mode. Programming Manual References [500] DISA Incoming Call Dial Mode [501] DISA Built-in AA Feature Manual References 1.1.41 Direct Inward System Access (DISA) [518] DISA Tone after Security Code Enables the PBX to send a short beep to the caller when the entered number is the same as one of the DISA security codes. Programming Manual References [512] DISA Security Code Feature Manual References 1.1.41 Direct Inward System Access (DISA) 516NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue ( Enable/ Disable) 517NEXTSELECTSTOREEND (1…5 s) 2 s 518NEXTSELECTSTOREEND ( Enable/Disable)
2.2 PT Programming—Procedures Programming Manual 55 [530] DISA Security Code Digits Selects the number of digits for the DISA security codes. Conditions When this setting is changed, DISA security codes that have already been assigned in [512] DISA Security Code will be cleared. Programming Manual References [512] DISA Security Code Feature Manual References 1.1.41 Direct Inward System Access (DISA) [531] DISA Ringback Tone Selects whether to send a ringback tone or Music on Hold to the caller when a DISA call is received. Feature Manual References 1.1.41 Direct Inward System Access (DISA) [540-549] 3-level AA Assignment Specifies the destinations of the DISA AA numbers as directed by 3-level DISA OGMs. Depending on the type of destination selected, it may also be necessary to select a specific destination (Extension/Extension Group). Conditions This program is available only when 3-level AA is selected for each AA number in [501] DISA Built-in AA. Only when you select as the third AA number, you can select 3-level AA in the next step. 530NEXTSELECTSTOREEND (4…10 digits) 4 digits 531NEXTSELECTSTOREEND ( Ringback Tone/ Hold Music) 5XNEXTEND (40… 49) NEXTPREVor To continue name*SELECT (Jack/GRP/ 3-level AA/ Not Stored)(0… 9, ) second AA no.third AA no. (0… 9) (01… 24) extension jack no. extension group no. (1… 8) or [ : Skip] STORE Go to another third AA number Go to next or prev. third AA number [40-49: AA no. 0-9]
2.2 PT Programming—Procedures 56 Programming Manual Programming Manual References [501] DISA Built-in AA Feature Manual References 1.1.41 Direct Inward System Access (DISA) [599] Clear All OGMs of DISA Clears all the prerecorded messages (DISA OGMs). Feature Manual References 1.1.88 Outgoing Message (OGM) for DISA [600] Extension Group Selects the extension group to which the extension belongs. Feature Manual References 1.1.21 Call Pickup, Group 1.1.42 Direct Inward System Access (DISA) Ring 1.1.53 Extension Group 1.1.67 Idle Extension Hunting 1.1.96 Paging—Group [601-603] TRS-COS—Day/Night/Lunch Selects the TRS COS for each extension, applied to outside (CO) line calls in each time service mode. 599NEXTSTOREEND 600NEXTextension jack no.extension group no.STOREEND (1…8)(01… 24/ ) To continue To continue SELECT NEXTPREVor 1 6XNEXTextension jack no.COS no.STOREEND (1…5)(01… 24/ ) To continue To continue SELECT NEXTPREVor (01… 03) 01: for day 02: for night 03: for lunch1
2.2 PT Programming—Procedures Programming Manual 57 Feature Manual References 1.1.32 Class of Service (COS) 1.1.117 Toll Restriction (TRS) [604] Extension Name Specifies the names of extensions, to be shown on the display of PTs during intercom calls. Conditions * An extension name can be entered using a PTs dialing buttons. The displayed character varies depending on the number of times that the dialing button is pressed. It is possible to toggle between Alphabet mode and Numeral mode by pressing SELECT. Programming Manual References 2.1 PT Programming—Instructions—Entering Characters [009] Extension Number Feature Manual References 1.1.43 Display Information 1.1.69 Intercom Call [605] Account Code Mode Selects the account code entry mode for each extension. Programming Manual References [310] Account Code [601-603] TRS-COS—Day/Night/Lunch 604NEXTextension jack no.extension name*STOREEND Max. 10 characters(01… 24) To continue To continue SELECT NEXTPREVor All-Not stored 605NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue ( Option/Forced/ Verify-All/Verify-Toll)
2.2 PT Programming—Procedures 58 Programming Manual Feature Manual References 1.1.2 Account Code Entry 1.1.118 Toll Restriction (TRS) Override by Account Code [606] Call Transfer to CO Line Enables the user to transfer an incoming call to any outside (CO) line. Feature Manual References 1.1.26 Call Transfer—To Outside (CO) Line 1.1.34 Conference, Unattended [607] Call Forwarding to CO Line Enables the user to forward an incoming call to any outside (CO) line. Feature Manual References 1.1.14 Call Forwarding (FWD)—To Outside (CO) Line [608] Executive Busy Override Enables the user to interrupt another extensions existing call to establish a 3-party conference call. 606NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable) 607NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable) 608NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable)
2.2 PT Programming—Procedures Programming Manual 59 Feature Manual References 1.1.50 Executive Busy Override—Extension 1.1.51 Executive Busy Override—Outside (CO) Line [609] DND Override Enables the user to make a call to another extension that is in DND mode, by entering the feature number. Feature Manual References 1.1.45 Do Not Disturb (DND) Override [610] Paralleled Telephone Specifies whether an SLT is connected in parallel with a PT. Feature Manual References 1.1.97 Paralleled Telephone [611] TAM Extension Specifies whether an extension is connected to a TAM to activate the Call Retrieving from a TAM feature. Feature Manual References 1.1.23 Call Retrieving from a TAM (Telephone Answering Machine) 609NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable) 610NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable) 611NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable)
2.2 PT Programming—Procedures 60 Programming Manual [612] Room Monitor Specifies whether an extension can be monitored using the Room Monitor feature. Conditions Extensions that are to be monitored must have their jacks set to Enable in this program in advance. Feature Manual References 1.1.110 Room Monitor [615] LCD Language Selects the language shown on the display of a PT. Feature Manual References 1.1.43 Display Information [617] Wireless PT Port Assignment Identifies whether a Panasonic wireless phone is connected to an extension jack or not. A phone without a Speaker (e.g., KX-TD7895 or KX-T7885) should be set to Connect, and a phone with a Speaker (e.g., KX- TD7896) should be set to Not Connect. 612NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue (Enable/ Disable) 615NEXTextension jack no.STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor ( English/ Spanish) To continue To continue 617NEXTextension jack no. name*STOREEND (01… 24/ ) SELECT SELECT NEXTPREVor To continue To continue( Not Connect/ Connect)