Panasonic Kx Ta824 Installation Manual

2.3 Installing Optional Service Cards
Installation Manual 51
2.Lift the edge of the card while holding the catch open. (Do not touch the circuit board of the card 
during the operation.)
Programming Manual References
[599] Clear All OGMs of DISA
8.5 DISA OGM Clear
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.88 Outgoing Message (OGM) for DISA
1.1.112 Station Message Detail Recording (SMDR) 

2.3 Installing Optional Service Cards
52 Installation Manual
2.3.8 2-Channel Voice Message Card (KX-TA82492)
Function
Provides 60 minutes of recording time (2 channels) for messages using the Built-in Voice Message 
Feature.
1.Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2.Slide the card between the guiderails until it clicks, and attach the connector to it.
Note
Use extra care to make sure you do not damage the part of the case marked with a circle....

2.3 Installing Optional Service Cards
Installation Manual 53
Programming Manual References
[808] BV Card Initialization
8.6 BV Card Initialization
Feature Manual References
1.1.8 Built-in Voice Message (BV) 

2.4 Connecting Outside (CO) Lines
54 Installation Manual
2.4 Connecting Outside (CO) Lines
2.4.1 Connecting Outside (CO) Lines
Connection
1.Insert the modular plugs of the telephone line cords (2-conductor wiring) into the outside (CO) 
line jacks.
2.Connect the line cords to the terminal board or the modular jacks from the telephone company.
To Terminal Board or Modular Jacks 
from the Telephone CompanyTRT: Tip
R: Ring TEL Jack for Outside (CO) Line 

2.5 Connecting Extensions
Installation Manual 55
2.5 Connecting Extensions
2.5.1 Connecting Extensions
Extension jacks can be used for proprietary telephones (PTs), Direct Station Selection (DSS) 
Consoles, single line telephones (SLTs), and Voice Processing Systems.
Note
Connect a display-equipped PT to extension jack 01, as this extension is automatically 
designated as the manager extension.
Connection
Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the modular...

2.5 Connecting Extensions
56 Installation Manual
2- or 4-conductor wiring is required for each extension as listed below. There are 4 pins that can be 
used for connection: T (Tip), R (Ring), H (High) and L (Low).
Note
If a telephone or answering machine with an A-A1 relay is connected to the PBX, set the A-A1 
relay switch on the telephone or answering machine to the OFF position.Telephone Wiring
SLT 1-pair wire (T, R)
PT (such as KX-T7736) 2-pair wire (T, R, H, L)
DSS Console 1-pair wire (H, L) 

2.5 Connecting Extensions
Installation Manual 57
2.5.2 Connecting Extensions in Parallel
Any single line telephone (SLT) can be connected in parallel with a proprietary telephone (PT) to a 
Hybrid Port as follows:
Note
An answering machine, fax machine or modem can be connected in parallel with a PT in the 
same way as an SLT can.
Feature Manual References
1.1.97 Paralleled Telephone
To a Hybrid Port
4-Conductor Wiring Cord
Connect pins T, R, H,
and L.2-Conductor Wiring Cord
Connect pins T and R.
SLT...

2.6 Connecting Doorphones and Door Openers
58 Installation Manual
2.6 Connecting Doorphones and Door Openers
2.6.1 Connecting Doorphones and Door Openers
Up to 4 doorphones (KX-T30865) and 4 door openers (user-supplied) can be installed.
Maximum Cabling Distance
Door opener current limit: 30 V DC/30 V AC, 3 A maximum
Installing the Doorphone (KX-T30865)
1.Loosen and remove the screw at the bottom of the case to separate the doorphone into 2 halves.
2.Pass the wires through the hole in the base cover, and...

2.6 Connecting Doorphones and Door Openers
Installation Manual 59
Note
2 kinds of screws are included with the KX-T30865. Please choose the appropriate screws for 
your wall type.
3.Connect the wires to the screws located in the front cover.
4.Re-attach the 2 halves and re-insert and tighten the screw.: when a doorphone plate has been fixed to the wall
: when you wish to install the doorphone directly to the wall
To the Terminal Box 

2.6 Connecting Doorphones and Door Openers
60 Installation Manual
Connecting Doorphones (KX-T30865)
1.Connect the Doorphone Card to the terminal boxes using 4-conductor wiring and modular 
connectors.
2.Connect the wires of doorphones 1 and 3 to the red and green screws on the appropriate 
terminal box.
3.Connect the wires of doorphones 2 and 4 to the yellow and black screws on the appropriate 
terminal box.
PanasonicPanasonicPanasonicPanasonic
Yellow
RedBlack
Green 4-conductor wiring
is required....