Panasonic Kx-Ta624 Advanced Hybrid System User Manual

PT Overview1-9
1.1 Configuration
Usage
AUTO ANSWER/MUTE Button
Used for answering an extension automatically, or turns the microphone off during a
conversation.
AUTO DIAL/STORE Button
Used for System Speed Dialing or storing program changes.
CONF (Conference) Button
Used to establish a three-party conference.
FLASH Button
Sends an External Feature Access signal to the central office or host PBX to access their
system features. If a PBX is not being used, this button can be used to disconnect the
current...

1.1 Configuration
1-10PT Overview
Flexible Buttons
Flexible Buttons do not have specific features permanently assigned to them. Features are
assigned to Flexible Buttons through Station Programming. “Flexible Button
Assignment” is addressed in Station Programming (Section 2). The four types of Flexible
Buttons are as follows.
• Flexible CO Buttons (located on a PT only)
• Flexible DSS Buttons (located on a DSS Console only)
• Programmable Feature (PF) Buttons (located on a PT and DSS Console)
• Flexible...

PT Overview1-11
1.1 Configuration
Line Access Buttons
One of the following three types of CO buttons must be used to seize an outside (CO)
line when making a call.
• Group-CO (G-CO) button
• Other-CO (O-CO) button
• Single-CO (S-CO) button
Conditions
• A flexible CO button can be assigned as a Line Access Button (G-CO, O-CO or S-CO)
in Station Programming. Once a flexible CO button is assigned as a Line Access
Button, it provides the line status using lighting patterns and color indication. Please
refer to...

1.1 Configuration
1-12PT Overview
Other-CO (O-CO) Button
Outside (CO) lines which are not assigned to S-CO or G-CO buttons can be assigned to a
flexible CO button on a proprietary telephone. The assigned button serves as the O-CO
button. An incoming call, on assigned outside (CO) lines, arrives at the O-CO button. To
make an outside call, you simply press the designated O-CO button.
Programming Reference
• Station Programming (Section 2)
Flexible Button Assignment — Other-CO (O-CO) Button
Feature...

PT Overview1-13
1.1 Configuration
Initial Settings
Display Contrast Adjustment (KX-T7030 and KX-T7130 only)
The CONTRAST selector is used to adjust the display contrast.
PT
HIGH          LOW
MID
CONTRAST
Adjust the CONTRAST lever to the 
desired setting (LOW/MID/HIGH).
PT
HANDSET      HEADSET
Adjust the HANDSET/HEADSET 
lever to “HEADSET”.
When using the headset (KX-T7030 and KX-T7130 only)
The Panasonic Advanced Hybrid System supports the use of a headset on a proprietary
telephone (PT). When you use the...

1.1 Configuration
1-14PT Overview
PT
NORMAL          HIGH      
HANDSET
VOLUME
Adjust the HANDSET VOLUME lever to the 
desired setting (three levels from NORMAL to HIGH).
Be sure the headset is connected.
PT
HIGH           OFF 
LOW
RINGER
Adjust the RINGER Volume lever to 
the desired setting (OFF/LOW/HIGH).
PT
VOLUME
Adjust the VOLUME Control lever to the 
desired setting (MAX to MIN).
MAX                       MIN
To adjust the headset volume
To adjust the ringer volume
To adjust the speaker volume...

PT Overview1-15
1.1 Configuration
LED Indication
The Light Emitting Diode (LED) buttons indicate the line conditions with lighting
patterns.
Flashing light patterns
LED Indication on the INTERCOM Button
The table below shows the lighting patterns for intercom line conditions.
INTERCOM button
Off
Green On
Flashing Green Slowly
Flashing Green Moderately
Flashing Green RapidlyIntercom Line Condition
Idle
Intercom call / Conference established
Intercom call hold
Intercom call exclusive hold
Incoming...

1-16PT Overview 

Section 2
Station Programming
(Personal Programming)
Contents
2.1 Station Programming Instructions  ...................................2-2
2.2 Station Programming (Personal Programming) (A - Z)  ...2-6

All illustrations used in these operating instructions are based on the
KX-T7130 model. 

2-2Station Programming (Personal Programming)
2.1 Station Programming Instructions
When storing data
After pressing the STORE button to store data, you may hear one of the following tones.
— Confirmation tone (one beep): storage is completed.
— Confirmation tone (two beeps): the data is the same as the last entry.
— Alarm tone (three beeps): the entry is not valid.
To exit the Station Programming mode
Station Programming allows you, the proprietary telephone (PT) user, to program certain
features from your...