Panasonic Kx-T30810 Installation Manual

~‘-------‘“----‘----------- AB= [-!+I: to assign the same on all 8 extensions. 
[ll]: on extension II 
[18]: on extension 18 
I....‘.......-- 
until the desired mode appears 
AUTO ANSWER. . . I . . . . . . . default (all8 extensions) 
MAN ANSWER 
I 
[14] [NEXT] [LB] [SELiCT] [ ORY] [END] 
;:] [NEXT] [NEXT] [SELECT] [ 
L-- -- until the desired extension number appears 
es 
By programming either automatic or manual 
answering can be set. The auto mode allows the 
user to answer incoming outside calls...

AB=[+]: to ussign rhe same on all 8 extensions 
;I:1 
El.51 [NEXT] [AB] [SELECT] [MEMORY] [END] 
or 
[15] [NEXT] [NEXT] [SELECT] [MEMORY] [END] 
L----- until the desired extension nutnber appears 
When any incoming calls from the Central Ofice 
are received at rhe same rime, !)ou can receive the 
call on the preferred line. 
“PREFERRED LINE” will be displayed. 
2. Press the NEXT button. 
“ENTER EXT NO” will be displayed. 
3. Press rhe NEXT butron. 
“11: m * * B ” 
will be displayed 
and 
“ 
* e 0 ea 
”...

[16] [NEXT] [AB] [SELECT] [MEMORY] [END] 
~6~~~EXT][NEXTI[SELECTI[MEMORYI[END] 
- 
L...... 
until the desired extension number appears 
During a conversation, call waiting tone will be 
heard when the third party on the outside or 
intercom calls you. 
Call waiting tone can be removed or added at 
customer’s request. 
Set to “ENABLE” for call waiting. 
“CALL WAITING” will be displayed. 
2. Press the NEXT button. 
“ENTER EXT NO” will be displayed. 
3. Press the NEXT button. 
“II: DISABLE” will be...

[17] [NEXT] [SEL II m [MEMORY] [END] 
Example: 
.^ . ^ . . . . 
10 seconds after the dlallng 
=[17] [NEXT] [SELECT] [ The duration time of the conversation is display- 
ed. 
Program the start time 
of the timing. 
Instantly after the CO line is captured. 
5 seconds after the dialing 
10 seconds after the dialing e 
See page S-16. 
“DURAT-TIME CQUNT” will be dis- 
played. 
ress the NEXT button. 
“5s AFTER DIAL” will be displayed and 
blink. 
3. Repeatpressing the SELECT button until the 
desired time...

A= [*I: to assign the same on all 3 CO’s 
until the desired flash timing appears 
~ ~-------------.---~I 
[I 81 [NEXT] [ii] [SELECT] [ 
;] [NEXT] [NFXT] [SELE 
i--- until the desired CO number appears 
es 
The timing of the hookswitch flash signal must 
s 
When you start the programming from step 1, 
be within the requirements from your Central 
you may dial the desired CO number instead 
of 
Office. 
the NEXT button at step 3. 
There are three choices available 0.3, 0.6 or 0.9 
second. The PREV button...

,...._______________. A= [ -tc]: to 
assign the sume on all 3 CO’s 
~~ 
until the desired disconnect time appears 
.~I 
[19] [NEXT] [k] [SELiCT] [MEMORY] [END] 
;9] [NEXT] [NEXT] [SELECT] [MEMORY][END] 
--.--- until the desired CO rlumber appears 
esc 
A certain amount of time is needed for a outside 
call to be released, this is necessary so that new 
calls may be attempted after disconnecting with 
the previous calls. 
There are two choices available, 1.5 and 4.0 
seconds. 6. Repeat steps 3 to 5, to...

A=[*]: to assign the same on a113 CO’s 
-a:ar; 
until the desired mode appears 
[20] [NEXT] [i4] [SELECT] [MEMORY] [END] 
~][NEXT][NEXTI(SELECT][MEMORY][ENDI 
.-.---- until the desired CO number appears 
To detect that an outside party has hung up and 
then terminate the outside 
(after a conversation, 
conference etc.) a CPC signal is needed. 
CPC signal can be removed or added at 
customer’s request. 
1. Dial (20). 
“CPC DETECTION” will be displayed. 
2. Press the NEXT button. 
“ENTER CO NO” will be...

_.......... 
until the desired mode appeurs 
TONE CALL.. . . . . . . . . . . . . . . . default (all 8 extensions) 
VOICE CALL 
I 
[21] [NEXT] [AB] [SELECT] [MEMORY] [END] 
;;;] [NEXT] [NEXT] [SELECT] [MEMORY][END] 
L---- until the desired extension number appears 
The intercom alerting mode (tone alertinglvoice 
alerting) at a receiving extension can be selected 
through programming. 
NE...Tone alerting (ringing) sounds at the 
receivitzg extension. 
VOICE.. Voice alerting instead 
of Tone alerting 
is...

:.‘-----.-‘----‘----‘---.-.-~ AB= [-?+I: to assign the same on all 8 extensions 
1 ..II..[::,~ 
I~_.____________ until the desired combination appears 
D-PHONE 1, 2 . I . . . . . defauh (aa 8 extensions) 
D-PHONE I 
D-PHONE 2 
D-PHONE * * 5 (deny the ringing) 
I 
[22] [NEXT] [riB] [SELiCT] [MEMORY] [END] 
;;;] [NEXT] [NE?T] [SELECT] [MEMORY] [END] 
~-----until the desired extension number appears 
Allows each extension to be programmed for 
receiving calls from up to 2 doorphones. 
A doorphone is option....

.--.-------..--------..-.----. AB= [*I: to assign the same on all 8 extensions 
until desired combination appears 
. default (all 8 extensions) 
[23] [NEXT] [AB] [SELECT] [MEMORY] [END] 
[g] [NEXT] [NEXT] [SELECT] [MEMORY] [END] 
L--- - until the desired extension rlumber appears 
Permits an extension user to answer other 
ringing telephones, provided that they are in the 
same pickup group. Each extension may belong to more than one 
pickup group, up to two, or does not belong 
the group. 
When you...