Panasonic Kx-T30810 Installation Manual

When the System Program Switch on the KX-T30810 is set to the PROGRAM position, the operation of the 
KX-T30830 will change as follows. 
PR PAUSE 
button 
,) button 
err? button 
-1 
EVIOUS button / CLEAR button 
PROGRAMMABLE 
FEATURE button 
/-.-----LIQUID CRYSTAL 
(LC) Display 
DIRECTSTATION 
SELECTION (DSS) button 
AUTOIMEMORY button 
CENTRAL OFFICE (CO) 
LINE 
button 
SELECT button 
INTERCOM (ICM) button 
END button A NEXT button 
2-2  

n Turn the Power Switch to ON 
. . . . . . . . . . . 
~ Set the System Program Switch to PROGRAM 
. . . . . . . . 
The LCD on the KX-T30830 shows “ENTER 
PGM CODE”. 
Be sure the handset 
of the extension 1’1 is in the cradle and 
the speakerphone button 
of the extension 11 is off. 
* To program automatic line access number 9 and the phone 
number 987-654-3210 into memory location {speed dial 
access) number 00. (Refer to page 2-5.) 
Dial (00) or press the  Dial (00) or press the 
NEXT button.  NEXT...

(______...._____._____.___.~...............~......._.____._______._._______.._.I_______ enter the year with 2 digits. 
[86]: 1986 year 
~‘..“..~“.......‘....~~.......~..‘....‘.~~.‘.~“.‘..“‘~~~‘.“’......’ 
until the desired month is 
displayed 
: . . . . . . . . . . . . . . . . . . ..-......_......_..___________________ enter the 
day with 2 digits 
,......._______________.______.__________ 
until the desired day of the 
week is displayed. 
,.._____...____.__.___..__ 
enter the hour with 2 digits...

._........__._....____..__...._....._.__.__________. 
I][phone number][ME 
To advance to the next code 
[SELECT][AB][CD][phone number][MEMORY] 
To exit the speed calling entry, press [END] 
~“TO]~~~XT]~~~~T]~~D]~phone number][ME 
L--- until the desired speed access code appears 
100 phone numbers each with up to 32 digits 
may be entered into programming for speed 
dialing use from each extension. 
Pushing the “-X-“, “#” “PAUSE”, “-” or 
“FLASH” button counts as 1 digit. 
. Enter the line access number....

8. Repeat steps 4 to 7. 
. To exit the speed dial entry, press the END 
utton. 
The LCD will show the initial program 
mode, “ENTER PGM CODE”. 
oc e 
Repeat steps 1 to 9. the 13 digits of a phone number, use 
‘, or ‘i@’ button for scrolling the 
display. 
The LCD will show the stored phone 
number. 
The line access number (9, 81, 82 or 83) 
should be stored. 
When dialing, the pause is automatically 
entered after line access number (9, 81, 82, 
or 
83). 
Continuous use of speed dialing is possible....

1) To enter line access number 81 and telephone number 201-392-4669 into speed access code 00. 
(OJ NEXT 00 81- 201-382-4669 MEMORY END) 
77 
Speed access j Telephone 
code number 
line access 
number 
If punctuations do not enter during a phone number, LC Display will show as below. 
(00: 812013924669) 
2) To enter automatic line access number 9 and telephone number 201-392-4669 into speed access code 02. 
Q-i NEXT 02 9- 201-392-4669 MEMORY END) 
-i-I 
: i 
Speed access j 
Telephone number 
code...

:-‘--------‘--‘--.---- A=-%: to assign thesame on a113 CO’s 
T.-‘.‘--.... 
until the desired dial mode appears 
i CONNECT. . . . . . . . default (al13 CO’s) 
NO CONNECT 
[02] [NEXT] [ii] [SELECT] [MEMORY] [END] 
;2] [NEXT] [NEXT] [SELECT] [MEMORY] [END] 
L--until the desired CO number appears 
s 
You can program that which outside line is 
connected and which one is not connected. 
When an extension automatically selects an idle 
outside line, the extension can be connected to it 
quickly. 
“CO...

- A= [-%I: to assign the same on all 3 CO’s 
until the desired dial mode appears 
default (all 3 CO’s) 
[03] [NEXT] [,4] [SELECT] [ME 
;3] [NEFT] [NEXT] [SELECT] [MEMORY] [END] 
1. _ _ _ _ 
until the desired CO number appears 
S 
Allows the user to select the dialing mode (tone 
or pulse) on each CO (Central Office) Line. 
TONE Dial Mode 
The dial signal from the extension (with tone or 
pulse dial mode) will be converted to TONE. 
TONE will then be transmitted to the Central 
Office. 
PULSE Dial Mode...

until the desired mode appears 
-~I 
[04] [NEXT] [SELkCT] [MEMORY] [END] 
&SC 
Allows DaylNight service to be selected manual- 
ly or automatically. 
In case of manual switching, refer to “Flexible 
Night Service” page 3-35. 
In case 
of automatic switching, set the “Starting 
Time (DaylNight Service)” page 2-11. 
The following features should be set. 
“Flexible Day Outward Dialing Assignment” 
page 2-13 
“Flexible Night Outward Dialing Assign- 
ment” page 2-14 
“Flexible Day Ringing Assignment”page 2-15...

‘------------.-----.---‘---------- A=[Ol] (o’clock): starting timefor day service 
[OS] (o’clock) . . . . . . . . , . . . . . default 
[12](o’clock) 
~------------.----“---. B=[OO] (minute). . . . . . . . . . . . . . . . . , default 
[ql] (minute) 
[is] (minute) 
~________.~. 
C=[Ol] (o’clock): starting time for night 
1651 (o’clock) service 
. . . . . . . . . . . . . default 
[ 121 (o’clock) 
--- D=[OO] (minute) . . . . . . . . . . . . . . default 
6 
[Ol] (minute) 
[59] (minute) 
7-71