Panasonic Kx-T123211d Remote Programming Manual

1 SHOW mode
1. Press them m kl ICR(I)I key.II1
L Main Command
Displav (In case of default)_.
I
I ;s > 10s
Example :
0 To change “after 3 min” to “after 7 min” in Hold Time Reminder.
0 To change “3 rings delay” to “4 rings delay” in call Forwarding Starting Time.
Press the111 mm 1/1m 111111 rim 111 IcR(IJ1key.
T TL Call Forwarding Starting Time
-
/Hold Time Reminder
Main Command
Programming TableSee page 11-8. 

-SYSTEM FEATURE-l 1
0 SMDR Parameters0 Duration Time Count Start Mode
@ Incoming/Outgoing Call Selection for printing0 External Paging Access Tone
0 Secret Speed Dial/One Touch Dial Printing0 DTMF Receiver Check
q EDIT mode,- See the table below.
IIPress the 
mmlsll/ll11111lr;l nmnmnmnmm key.Parameter no.
! L
LL
DTMF Receiver Check
External Paging Access Tone
Duration Time Count Start Mode
Secret Speed Dial/One Touch Dial Printing
LL
k Incoming/Outgoing Call Selection for printing
SMDR Parameters
Main...

q EDIT mode (cont.)Note 
0 SMDR Parameters must be entered with page length and skip perforation.
0 DTMF receiver 1 through 3 are entered at a time.
DTMF Receiver 3
DTMF Receiver 2
DTMF Receiver 1
Example :To change 
“66 lines” to “77 lines” in Page Length of SMDR Parameters.
To change “00” to 
“05” in Skip Perforation of SMDR Parameters.
To change “5 sec. after dial” to “Instantly” in Duration Time Count Start Mode.
Press the 
~lT;1~~T;1~~~~T;1~~~lTjl[?lT;1~lT;llcRoJkey.
Duration Time Count Start Mode
-...

*SYSTEM FEATURE-l 2
Direct Inward System Access (DISA)
0 Security Type
l User Security Code
0 Remote Security Code
0 Answer Delay Time
0 Prolong Time
0 Control code “ Jc”
0 Tone Detect
W EDIT modeISee the table below.IParameter no.
010203040506
LUser Security Code 4
L L
L
ITone Detect
Control code-“*”
Prolong Time
Answer Delay Time
-Remote Security Code
L LL
I User Security Code 3
User Security Code 2
User Security Code 1Security Type
Main Command
SecurityIUser Security Code
123Security
4Code
0 : None
1...

Example :
To change the “Trunk” to “All” in the Security Type ;To change the “0000” to “1234” in the User Security Code 2 
;
- User Security Code 2
- Security Type
- Main Command
I SHOW mode
1. Press the 
m m m ICR(I)Ikey.
IIMain Command
Programming TableSee page 
11-l 0.Display (In case of default)
;s > 12s
;=> 
12S/l /0000/0000/0000/0000/0000/2/3/1 /l /
I--,; s > L-1 

.’
c
SYSTEM FEATURE - 13
e Day/Night Service Mode (Starting Time)
n EDIT modeSee the table below.
Press thenm(SIOm’m’IOlcRoI
L- Main Command
IL
IStarting Time of Night Service Mode
Starting Time of Day Service Mode
- Subcommand
0 : Sunday
1 : Monday
2 : Tuesday
3 : Wednesday
4 : Thursday
5 : Friday
6 : Saturday
* :To assign
the same
on day of
the week
q SHOW mode1. Press the 
l~~~~lCR(I)I key.Parameter no.
0102Starting Time of DayStarting Time of Night
Service ModeService Mode
cl0 III El0 To set a same...

SYSTEM FEATURE-90
IS-232C Communication Parameters
0 Carriage Return for a New Line
0 Baud Rate
0 Word Length
0 Parity
0 Stop Bit Length
I EDIT mode
ISee the table below.
Press thelqqqr;ln~~I~~n~r;ll~r;ll~T;llcRoINote7
II
L L
I
I-
0 You can not access RS-232C communication
Baud Rateparameters with on-site administration
programming. (It will function with remote
Stop Bit Length
administration).Word Length
90s can be dumped with Dump mode with
remote 
/ on-site administration.L- Carriage Return for a New...

n SHOW modeDisplay (In case of default)
1. Press the 
m kj m ICR(I)Ikey.
IIMain Command
Programming TableSee page 
11-l 0.
-. - 21‘. 

OUTSIDE LINE FEATURE-lI CO Connection Assignment
) Dial Mode
b Host PBX Access Codes Assignment
1 Trunk Group Assignment
) Automatic Designated CO Line Access
lCO Mode (Normal / Direct In Line / Direct
Inward System Access) Assignment
l Pause Time Assignment
l Hookswitch Flash Timing
0 Calling Party Control (CPC) Signal
l Disconnect Time
‘T modeSee the table on page 6-2.
‘eld!llnLv
L!
ILAutomatic Designated
CO Line AccessDisconnect Time
CPC Signal
Hookswitch Flash Timing
Pause Time Assignment
LMain...

c
f06 1 07
CO Mode
01040512
Automatic
Designate
CO LineAccess0809
PauseHookswitch
TimeFlash
AssignmentTiming10CPCSignal
11Disconnect
Time 0203 Parameter no.coConnectionAssignmentDial ModeTrunk
Group
AssignmentHost PBX
Access
Codes
Assignment
1 or 2 digitsMax codes:
8
\\ParameterPulse
Speed
Selection
0:Low
1 
:HighDTMF 
IPulse I
Call
Blocking
Selection
0:DTMF
1 :Pulse2:Call
Blocking
DayModeNight
Mode
1 
:Group 1
2:Group 2
8:Group 80:Normal0:1.5 set0:BOOmsec1:2.5 set1:600msec2:3.5 set2:900msec3:4.5...