Panasonic Kx-T123211d Remote Programming Manual

							EIA/REMOTE
PROGRAMMINGMANUAL 
’
KX-T123211 D
ELECTRONIC MODULAR SWITCHING SYSTEMPlease read before use. 
						

							Preface
KX-Tl23211 D EMSS has function that programming or
reprogramming (Showing, Editing, Dumping so on) can be done by
using a RS-232C interface port or a MODEM (through a Central
Off ice) from the place where KX-Tl23211 D is set and far.nThe Card which should be installed to KX-Tl23211 D consists of
the following cards.
0 Direct Inward System Access Cards KX-T123291
0 MODEM Card KX-T123296
nWhen use the RS-232C interface port (On-site Administration)nProgramming or reprogramming can be done by connecting it toIf Outgoing Message is sent when a call is sent to KX-Tl23211 D,
KX-T123211 D at the same place as it.you will be able to confirm that the call arrived to the other party,
so this card is useful.
0 Outgoing Message Card KX-T123292
n
Data terminal equipmentn When use the MODEM (Remote Administration)
Programming or reprogramming can be done through a Central
Office from the place where 
KX-Tl23211 D is in a few handreds
miles away.
Data terminal equipmentTelepone
Line
KX-T1232 11 D
.;7 - 1Data terminal equipment
We recommend a data terminal equipment provided with a display
(Example KX-D4985 Panasonic).
A data terminal which is not equipped with a display can print out a
data automatically, so this can be used, too.
\‘Lit.- ;--.,’ 
						

							Feature
Edit 1 ShqwProgram to KX-T123211 D newly or the preset programming
contents are displayed on the display of the data terminal
equipment and then confirm (by show mode) or change (by edit
mode) them.H Dump
The preset program data in KX-T123211 D can be copied to the
floppy disk in a disk drive of a data terminal equipment.
n System Working Report
Interactive StyleShowing or Editing of data is done with a conversation style like
that after one person ask, the other person answer.The number of incoming calls, answered of incoming calls and
unanswered of incoming calls and the number of access
’requested, access succeeded and access failed are reported.
Batch StyleAfter store the data which is preset or wish to change with a
floppy, the data can be transmitted to 
KX-Ti 23211 D at a time and
program can be done.
When a data is entered at a time at the place where
KX-T123211 D is set, RS-232C interface port is used and when a
data is entered from far, send a data at a time after call the other
w-WI
I
In this Manual, the model No. KX-T123211 D is abbreviated to
KX-T123211.l-2 
						

							Contents
Outline of the Operation.............................3-lPreparation
On-site Administration..........................3-2
Remote Administration...........................3-3
On-site 
/ Remote Administration Start
On-site Administration Start......................3-4
Remote Administration Start.......................3-4
On-site 
/ Remote Administration Start Map...........3-5
On-site 
/ Remote Administration End
On-site Administraion End.......................3-8
Remote Administraion End........................3-8On-site 
/ Remote Administraion End Map...........3-7
To Edit the Data by “lntaractive Style”..................3-8
Editing or Programming..........................3-gTo Show the Data by “Interactive Style”..............
3-l 1
Showing....................................3-l 2To Edit or Show the Data by “Batch Style”............3-13
To make the batch data........................3-15
Edit / Show Mode Map............................‘$17
To Dump the Data...............................‘J-1 8
Dump Mode Map.............................‘J-20
.To Dump or Clear the System Working Report (SWR)
System Working Report Map. . . . . . . . . . . . . .
Example of Programming
To edit the data by “Interactive Style”
with Remote Administration
. . . . . . . . . . . . . . . .The way of seeing table
. . . . . . . . . . . 9 . . . . . . .
. .
. .
. .. . 3-21
. . .3-22
. . . . .4-l
. . . . .4-3
2-1
Format
SYSTEM FEATURE-1. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-l
0 Extension Number Assignment-l (for Jack number 01 through 16)
SYSTEM FEATURE-2. . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
0 Extension Number Assignment-2 (for Jack number 17 through 32)
SYSTEM FEATURE-3. . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
0 System Speed Dialing Entry
SYSTEM FEATURE-4. . . . . . . . . . . . . . . . . . . . . . . . . . 543
0 Date and Time Setting
0 Operator Assignment
0 Automatic CO Hold Using DSS Button
0 Day/Night Service Mode
0 Call Hunting
SYCJ-EM FEATURE-5. . . . . . . . . . . . . . . . . . . . . . . . . . 543
0 Area Type Selection
0 CO Operator Call Boundary Class
0 Toll Restriction of System Speed Dialing
SYSTEM FEATURE-6. . . . . . . . . . . . . . . . . 5-gl Toll Restriction-Allowable Exchange Code Selection
SYSTEM FEATURE-7. . . . . . . . . . . . . . . . . . . . . . . . .5-10
0 Toll Restriction-Area Code Entry for Class 3
SYSTEM FEATURE-8. . . . . . . . . . . . . . . . . . . . . . . . .5-11
0 Toll Restriction-Exchange Code Entry for Class 5
SYSTEM FEATURE-9. . . . . . . . . . . . . . . . . . . . . . . . .5-12
0 Toll Restriction-Exchange Code Entry for Class 7 
						

							SYSTEM FEATURE-10. . . . . . . . . . . . . . . . . . . . . . . . . .5-13
0 Hold Time Reminder
0 Hold Recall Time Set
0 Transfer Recall Time
0 Call Forwarding Starting Time
0 Pickup Dial Delay Time
l CO to CO Duration Time Limit
0 Off Premise Extension (OPX)
0 Off Hook Call Announcement (OHCA)
l Call on Hold for Standard Telephone
SYSTEM FEATURE-1 1. . . . . . . . . . . . . . . . . .
0 SMDR Parameters
0 Incoming/Outgoing Call Selection for printing
0 Secret Speed Dial / One Touch Dial Printing
0 Duration Time Count Start Mode
0 External Paging Access Tone
0 DTMF Receiver Check
SYSTEM FEATURE-1 2. . . . . . . . . . . . . . . . . .Direct Inward System Access (DISA)
SYSTEM FEATURE-13. . . . . . . . . . . . . . . . . .
0 Day/Night Service Mode (Starting Time)
SYSTEM FEATURE-90. . . . . . . . . . . . . . . . .
0 RS-232C Communication Parameters
. . .
. . .. 5-15
. 5-19
. 5-20
OUTSIDE LINE FEATURE-1. . . . . . . . . . . . . . . . . . . . . . . . 6-l
0 CO Connection Assignment
0 Dial Mode (DTMF/PuIse/CalI Blocking)
0 Host PBX Access Codes Assignment
0 Trunk Group Assignment
0 Automatic Designated CO Line Access
0 CO Mode (Normal / Direct In Line / Direct Inward System
Access) Assignment
0 Pause Time Assignment
0 Hookswitch Flash Timing
0 Calling Party Control (CPC) Signal
0 Disconnect Time
CPC Signal Detect Time . . . . . . . . . . . . . . . . . . . . . . . . G-3OUTSIDE LINE FEATURE-2M
. . . . . . . . . . . . . . . . . . . . . . 6-4
0 Flexible Outward Dialing Assignment (Day/Night Mode)
OUTSIDE LINE 
FEATURE-4/5. . . . . . . . . . . . . . . . . . . . . . 6-5
0 Flexible Ringing Assignment (Day/Night Mode)
OUTSIDE LINE FEATURE-fj/T. . . . . . . . . . . . . . . . . ..+343
0 Delayed Ringing Assignment (Day/Night Mode)
EXTENSION FEATURE-1. . . . . . . . . . . . . . . . . . . . . . . . . . .7-l
0 Extension Group Assignment
0 Service Class Assignment of Toll Restriction
0 Extension Name
0 Account Code Input Mode
0 Call Transfer to Outside Line
0 Call Forwarding to Outside Line
0 Executive Override
0 Do not Disturb Override
2 
--2 
						

							Contents (cont.)
EXTENSION FEATURE-2..........................7-3
0 Flexible CO Button
DOORPHONE FEATURE-l/2.......................8-l
0 Ringing Assignment of Doorphone (Day/Night Mode)
DSS CONSOLE FEATURE-1.......................g-1
0 Paired Telephone Assignment for DSS Console
DSS CONSOLE 
FEATURE-2/3.....................
9-2
@ DSS Console 1 or 2-Flexible DSS Button
CLEAR FEATURE..............................10-l
Programming Table.............................11-lSupplement
Kinds of Setting Mode Command and Prompt.......
12-1
Disposal Style...............................12-l
Note.......................................12-l
“HLP” Command.............................12-l
Main Command System........................12-2
DisposalExecuteCommand.....................12-2The way to enter Disposal Execute Command.......
12-3 
						

							Outline of the OperationTo edit or show the system programTo dump the system data or system working reportPreparationSee pages 3-2 and 3-3.PreparationSee pages 3-2 and 3-3.
StartSee page 3-4.StartSee page 3-4.
Mode Selection
Edit 
/ Show mode
0 Interactive Style
0 Batch StyleSee pages 3-8
through 3-17.
EndItem Selection
1 Programming 1See pages 5-1
through 10-l.
See page 3-6.See pages 3-18
through 3-22.
EndSee page 3-6. 
						

							On-site / Remote Administration Start1. Set the System Program Switch on the KX-Tl23211 to the “EIA”
position.The display on data terminal will show ;
; Welcome to KX-Tl23211 on-site administration
Iver 2.0 Panasonic CO., LTD
; ** Jan. 1. 1988 
12:OO’AM **3. After the answer carrier tone, set the on-line mode on your data
terminal equipment.
l The display on data terminal will show.
; The “HLP” displays command informations; Welcome to KX-Tl23211 remote administration1ver 2.0 Panasonic CO., LTD
; ** Jan. 1. 1988 12:OO’AM **; ** Jan. 1. 1988 12:OO’AM **
; The “HLP” displays command informations’ ; The “HLP” displays command informations’
l---dl---d; > L-1; > L-1n When you set the programming switch to the 
“EIA” position, the
system will stop its own normal exchanging operations, disconnect
all the current calls, and connect same extensions to CO lines
directly with the power failure transfer feature.
CO1 will be assigned to extension of jack number 01
CO2 will be assigned to extension of jack number 02
CO5 will be assigned to extension of jack number 09
CO6 will be assigned to extension of jack number 10
CO9 will be assigned to extension of jack number 17
CO1 0 will be assigned to extension of jack number 18
0 Be sure the System Program switch on the KX-Tl23211 is set to
the “SET” position.
1. Make a call to the line which is beforehand programmed as a 
DISALine on the KX-Tl23211.
0 Dial tone will be heard.
0 If the Outgoing Message Card is installed to KX-Tl23211,
Outgoing Message will be heard instead of dial tone.
2. Dial the Remote Security Code (70000 through 79999).
You will hear the answer carrier tone.
0 Whenever you don’t know which commands should be entered next,
press “HLP” and Carriage Return Keys. You will find the next
command (See page 12-l).
3-4
3-2 
						

							On-site administrationSet the SystemProgram Switch
to the 
“EIA”Remote administraion
communication
I:Indication on
display of data
terminal .
eqipment
; Welcome to KX-T123211on-site administration; Welcome to KX-T123211remote administration
ver 2,0 Panasonic CO., LTD
;ver 2.0 Panasonic CO., LTDIII
1; ** CurCent ;ime ** 1
; The “HLP” displays command informations
(Process of Operation)
. 
						

							c
On-site / Remote Administration EndReturn the System Program Switch on the 
KX-Ti 23211 to the
“SET” position from the “EIA” positionMake your data terminal equipment off-line or hang up or enter
“BYE” command.
when you enter the “BYE” command;
; ** Jan. 1. 1988 12:OO’AM **
; 
KX-Ti 23211 remote administration end
; ** Jan. 1. 1988 12:OO’AM **
; KX-T123211 on-site administration end
0 If carrier tone from the data terminal equipment stop while data
communication, the operation with Remote administration will
finish.
3-6