Panasonic Kx-T123211d Remote Programming Manual

							(Process of Operation)0:Indication on display of
data terminal equipment
Remote administration
end command
On-site administration
Return ‘theSystem Program
Switch to theRemote administration
I L; KX-Tl23211 on-site administration end
; KX-T123211 remote administration end
\
Dataterminal
equipment
off-line,
hang up or
Carrier
tone stop
(On-site 
/ Remote Administration End)
-9 
						

							.,
,‘..:
c
To Edit the data by “Interactive Style” (cont.)n If you want to change just one parameter of many parameters, you may press 
I‘ I#I ” key and the parameter number and then press
“ 1/1 m 111 JcR(1)I ” key. .
; E 
> Main command 1 1 SubcommandICII# Parameter number
Example ;In case of changing the 15th
; E > Main command
or; E > Main command
In case of changing the 1st
; E > Main command
or; E > Main command
Subcommand 1llll1llll
SubcommandJpJ15l~l/
SubcommandI piiEzqIIcR(1)I
SubcommandI#I 011 )j / IcRcr,l
n In case you want to show the setting contents with Edit Mode without changing to show Mode, enter “/ /” after commandas follows.
MS 
// 1 (To see all parameter with Subcommand S of Main Command)
To see the Starting Time of Day/Night Service Mode on Monday, press 
13Sl/ / 1 .
M 
*:/ / 1 (To see all parameter with Subcommand of Main Command at a time)
To see the Starting Time of Day/Night Service Mode on Sunday through Saturday, press 
13s t / / 1 .
M // 1(To see all parameter with Main Command)
To see the Parity, Carriage Return for a New Line, Word Length, Stop Bit Length and Baud Rate, press 
90% / 1 .
.3-B 
						

							To Show the Data by “Interactive Style”1. Press the q q q and 1 Carriage Return ( 1 ) 1 key.
Rl If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
;Select the styleInteractive. . . . . . . . . . . . .INT (cr)
,Batch . . . . . . . . . . . . . . . . . .FIL (cr)
,Mode end . . . . . . . . . . . . . .END (cr)
b--v; > !.,.!2. Press the
fl w q andICarriage Return ( 1 ) 1 key,
; > int
;Interactive style start
I--,; s> 1-1q If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; S> hlp
;Please input show command (current style : interactive)
L
r-7:,=\I I‘-.I3. Enter the commands corresponding to the feature that you want to
know. (See page 3-12)
4. To see another data, repeat step 3.
5. Press the 
m w IDI and lCarriage Return ( 1 ) 1 key.
6. Press the q q q and 1 Carriage Return ( 1 ) 1 key.
; > end
;Show mode end
l--q
; > L-1
3 -- I I
., 
						

							L
To Show the Data by “Interactive Style” (cont.)Enter the command corresponding to the feature that you want to show according to this format.
; S > Main commandIpi%izal~ICR(I)IThe feature names or the data of Main 
cammand and Subcommand that you want to show are explained on page 5-l through 10-1, so enter
them according to this table, please.
0 “CR ( 1 )” means Carriage Return ( 1 ).
3- 12 
						

							To Edit or Show the Data by “Batch Style”
l.Pressthem(H(m 1Carriage Return ( 1 )key to select the
Show mode, or
q q q1 Carriage Return ( 1 )I key to selectthe Edit mode.
When Edit mode:
; >edt
;Edit mode start
; > 
f;jWhen Show mode:
; > shw
; Show mode start
In If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
;Select the styleInteractive
. . . . . . . . . . . . . .,INT (cr)
Batch . . . . . . . . . . . . . . . . . .FIL (CT)Mode end . . . . . . . . . . . . .
END (cr)
I--,; > !-!
2. Press the m rl q and1 Carriage Return ( 1 ) 1 key.
; > fil
;Batch style start
I
I--.IL3. Transmit the batch data to the KX-T123211.
The system data will be shown on the display.
4. When transmission of system data has been finished, the display
will show the following.
n If “EOD” data is programmed in batch data;
; Batch style end
; > 
[:IIf enter 
“CNT” command;
When Edit mode:
; E> cnt1Transmit the next batch data
r--lI II.-.!When Show mode:
r f “nsmit the next batch data
0 To show or edit another data, repeat step 3.
. 
						

							To Edit or Show the Data by “Batch Style” (cont.)n If “EOD” data is not programmed in batch data, the display will
show the following after two minutes.
When Edit mode:
5. Press q q q 1 Carriage Return ( 1 ) 1key.; None “EOD” In batch data
r-3; E> ‘.-;When Show mode:
; None 
“EOD” In batch data
l---l; s> 1-JWhen Edit mode:When Show mode:
0 To end the batch style, pressq R q 1 Carriage Return ( 1 ) 1
key.
0 To continue the batch style, press the
q q q 1 Carriage Return ( 1 ) 1 key and repeat step 3.
0 If you wish to know the effective commands which can be used on
this mode, enter the “HLP” command within two minutes.
; Select the command (current style : batch)
fBatch mode end . . . . . . . . . . . . . . . . . *END (cr)
Next batch data
. . . . . . . . . . * . . . . . . .ICNT (cr)
I--*
; s>!.-l1 ;Show mode end
3 
- 14 
						

							1. Set a floppy disk to the drive of a data terminal equipment.
2. UTo chanqe or proqram a data
0 Enter the command (Main command, Subcommand) and
parameter corresponding to the feature that you want to
change as the way on page 3-9 “Editing or Programming”.
0 When change the other feature, repeat step 0.
O After entering all the data, enter “EOD”.
UTo confirm a data
0 Enter the command (Main command, Subcommand)
corresponding to the feature that you want to confirm as the
way on page 3-12 “Showing”.
0 When confirm the other feature, repeat step 0.
a After entering all the data, enter “EOD”.
3. Make the floppy memorize the entered data.
Example :
q Change or program _Make the data to edit as follows and memorize the data to the
floppy disk.
0 To change the Extension number which is assigned to jack
number 01 into 190.
e Jack number 02- Extension number 185
0 Jack number 04- Extension number 180
0 Jack number 17- Extension number 165
e To set date into Aug. 31’ 88 (Wednesday)
Enter them to the data terminal equipment as below
OlS/90/85/180/ 1
02s / 65 I 1
04Sl8808313l 1EOD 
1
Note
0 EOD is surely made in the end of batch data.
e One line up to 78 digits.
0 Be sure to press the “Carriage Return ( 1 )” key in conclusion of
one data.
0 “ 1 ” means Carriage-Return.
3- 13 
						

							c
To Edit or Show the Data by “Batch Style” (cont.)(To recognize the made data)
If q is entered in the first line, the line will not be executed when abatch data is sent to the 
KX-Ti 23211 from a data terminal
equipment.
If the title of the change contents are entered in the line as following,
it will be useful when use it later because of the recognition of the
contents.
02s I 65 I 1r-------------------------,‘1. DATA=‘88. 8. 37. (WED)SET11rl------------------------r
04s I 8808373 I 1
EOD 1To show the data of SYSTEM FEATURE-l through 6
(see page 5-1 through 5-9)
Make the data code as follows and memorize the data code to the floppy disk.
ys 102s 
103s 
* 1
04s 1
05s 1
06s * 1EOD 
1
n Confirmation3 
- 76 
						

							Edit / Show Mode Map
I-;>INT
s
; Select the style
;Interactive . . . . . INT (cr)
;Batch . . . . . . . FIL (cr)
;Mode end . . . . . END (cr)
j j Ftyctive style startb
rI
/ j lgactive style startp(Interactive process)
‘7)) j B~~~~$fi~~~ batch data> I- (Batch process)
3- I/.0 
						

							c
To Dump the Data
1 .Press them m IpI 1 Carriage Return ( 1 ) 1 key.
I; > dmp
I; Dump mode startI
I
l---l; p> L-1n If you wish to know the effective commands which can be used on
this mode, enter the “HLP” command.
; P> hlp
; Select the item
..............................
IAlIALL (cr)..........................
FSystemSYS (cr)
ICO. trunk........................COT (cr)
,Ext..............................EXT (cr)
IDSS console.....................DSS (cr)
........................DoorphoneDOR (CT)
........................IMode endEND (cr)
; P> [;I
L
2.Before input of the following commands, set floppy disk to the
data terminal equipment so that the data terminal equipment
can start recording.
Press the command of the parameter that you want to dump.
n The first message will be displayed as follows when eachcommand is entered.
ALL; All data dump start
SYS; System data dump start1COT 
-1 ; CO data dump start1
EXT; Ext data dump start
DSS 
-1; DSS console data dump startIn The following message will be displayed when Dump is finished.
IDORIDoorphone ParameterI
DOR; Doorphone data dump start
ALL 
-1 ; All data dump end
SYS; System data dump endICOT
EXT; CO data dump end
; Ext data dump end
DSS 
- ;DSS console data dump end
DOR- ;Doorphone data dump end
3 - 18