Panasonic Kx-T123211d Remote Programming Manual

To Dump the Data (cont.)Example; When dump System parameter
; P>sys
; System data dump start
OlS/Ol /02/03/04/05/06/07/08/09/10/11 /12/13/14/15/16/
02S/17/18/19/20/21/22/23/24/25/26/27/28/29/30/31/32/
lOSl3Jl I1 /3/3/10/0/1/11
1lSl66,OOJ3JOJl J3Jlll J
12S/1/0000/0000/0000/000010000/2/3/1 JlJ
13soI 09000 / 05001I
13SlJ 09000 / 05001J
13S2/09000/05001J
13S3J 09000 / 05001I
13S4J09000/05001J13%I09000/05001J\
13S6J09000/05001J
9OSJl JOlOJ.OJ4J
EOD EOD; System data dump end ; System data dump end
; P> ; P>3....

c
To Dump the Data (cont.); Dump mode start
I 
I/
II I\
l-; P>
HLP
F
; Select the item.A,, . . . . . . . . . . , . . . . A,,(cr)
;System . . . . . . . ‘. . . SYS (cr);CO. trunk...........COT (cr).Ext...............EXT (cr)
;DSS console........DSS (cr);Doorphone..........DOR (cr);Modeend..........END (cr)
; All data dump start
; System data dump start----- (System data dump process)--------
; CO data dump start----- (CO data dump process) ------------
1---- (All data dump process) ------------; All data...

To Dump or Clear the System Working Report (SWR)
1. Press theq q q 1 Carriage Return ( 1 ) 1key.
; > rpt
;System working report mode start
; R>f:;
1 If you wish to know the effective commands which can be used
on this mode, enter the “HLP” command.
l-; 
R>hlpSelect the item
SWR data dump . . . . . . . . . . 
’ .DMP(cr)SWR data clear . . . . . . . . . . . .CLR
(cr)Mode end . . . . . . . . . . . . . .END(cr); 
R> i;j2. 
0To dump the System Working Report, press the
IDI q q ICarriage Return ( 1 ) 1key.
;...

c
To Dump or Clear the System Working Report (cont.); System working report mode start
I:R>
I I’
11
HLP
DMP
ICLR
; Select the item
;SWR data dump . . .DMP (cr)J
;SWR data clear . . . . . . . .CLR (cr).
,Mode en,-J . . . . . .END (cr)(SWR data dump process)
(SWR data clear process) 
I...... ; SWR d
=a
* System working report mode end
”
- 22 

Example of Programmingn Installation of the following optional cards are necessary.
0 Direct Inward System Access Cards KX-T123291
0 MODEM Card KX-T123296
4. Press the q Id Fi1 Carriage Return ( 1 ) 1 key.and
I
n PreparationSee pages 3-2 and 3-3.
1. Make a call to the line which is beforehand programed as a 
DISAline on the 
KX-T123211.2. Dial the Remote Security Code (70000 through 79999).
3. After the answer carrier tone, set the on-line mode on your data
terminal equipment.
; Welcome to KX-T123211...

Example of Programming (cont.)6. Change the feature corresponding to the extension connected to the
Jack number 
10 as following.7. To edit another data, repeat step 6.
Change Extension Group Assignment to group 5.
Change Account Code Input Mode to Forced.
(Refer to page 7-2)8. To end the Interactive style mode, press the
14 bl q and
ICarriage Return ( 1 ) 1 key.
I
I
Press theq oooo@nooo~o~Interactive style endI . I .r-q,....... . . . . . .
;. . . Carriage Retrun; > 1-1
:... Parameter no. 05
(Account...

Tables are written every each command in order, so enter according to these tables.
The contents indicated with show mode are same as this format.l-Parameter no. of Service ClassParameter no. of Do
Assignment of Toll RestrictionIParameter no.I
02
ExtensionService Class
GroupAssignment of Toll
AssignmentRestriction (Day Mode)
1:Group11:Class1
8:Group88:Class8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

SYSTEM FEATURE-1
Extension Number Assignment-l (for Jack number 01 through 16)
E EDIT mode,- See the table below.
I
Press the pJ~jq&fl~pj --------- ----------------------------- p-jIcR(I)I key.L
LJack no. 02
Enter the extension number if you want to change it which is
assigned to jack number 01.
Need not enter the extension number if you do not want to
change it.Main Command
Note 
o The extension number should be programmed with last 2 digits.
However, the practical extension number is 3 digits.
0 You...

Example :To change the extension number which is assigned to jack number 02 to 140, the extension number which is assigned to jack number 05 to 150
and the extension number which is assigned to jack number 07 to 155.
IIII
T
Extensionnumber which is assigned to jack number 07
Extension number which is assigned to jack number 05
Extension number which is assigned to jack number 02
Main Command
0 If the data of extension number which you want to change is one, you may use parameter number instead of...

SYSTEM FEATURE-2 c
Extension Number Assignment-2 (for Jack number 17 through 32):
;‘1n EDIT mode,- See the table below.
III
Press the 1qqq~n~n~_---__-- ____________ -___- ____ -___-__-- l~lc~(1)11 key.L
II-
IJack no. 18
Enter the extension number if you want to change it which is
assigned to jack number 17.
Need not enter the extension number if you do not want to
change it.Main Command
Parameter no. 01
FLThe extension number can be programmed from 00 to 99.
02s i(none) IO0 IO0 ICI0 IO0 IO0 IO0 IO0 IOU...