Panasonic Kx-T123211d Remote Programming Manual

(Process of Operation)0:Indication on display of
data terminal equipment
Remote administration
end command
On-site administration
Return ‘theSystem Program
Switch to theRemote administration
I L; KX-Tl23211 on-site administration end
; KX-T123211 remote administration end
\
Dataterminal
equipment
off-line,
hang up or
Carrier
tone stop
(On-site 
/ Remote Administration End)
-9 

.,
,‘..:
c
To Edit the data by “Interactive Style” (cont.)n If you want to change just one parameter of many parameters, you may press 
I‘ I#I ” key and the parameter number and then press
“ 1/1 m 111 JcR(1)I ” key. .
; E 
> Main command 1 1 SubcommandICII# Parameter number
Example ;In case of changing the 15th
; E > Main command
or; E > Main command
In case of changing the 1st
; E > Main command
or; E > Main command
Subcommand 1llll1llll
SubcommandJpJ15l~l/
SubcommandI piiEzqIIcR(1)I
SubcommandI#I 011...

To Show the Data by “Interactive Style”1. Press the q q q and 1 Carriage Return ( 1 ) 1 key.
Rl If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
;Select the styleInteractive. . . . . . . . . . . . .INT (cr)
,Batch . . . . . . . . . . . . . . . . . .FIL (cr)
,Mode end . . . . . . . . . . . . . .END (cr)
b--v; > !.,.!2. Press the
fl w q andICarriage Return ( 1 ) 1 key,
; > int
;Interactive style start
I--,; s> 1-1q If you wish to know the effective...

L
To Show the Data by “Interactive Style” (cont.)Enter the command corresponding to the feature that you want to show according to this format.
; S > Main commandIpi%izal~ICR(I)IThe feature names or the data of Main 
cammand and Subcommand that you want to show are explained on page 5-l through 10-1, so enter
them according to this table, please.
0 “CR ( 1 )” means Carriage Return ( 1 ).
3- 12 

To Edit or Show the Data by “Batch Style”
l.Pressthem(H(m 1Carriage Return ( 1 )key to select the
Show mode, or
q q q1 Carriage Return ( 1 )I key to selectthe Edit mode.
When Edit mode:
; >edt
;Edit mode start
; > 
f;jWhen Show mode:
; > shw
; Show mode start
In If you wish to know the effective commands which can be
used on this mode, enter the “HLP” command.
; > hlp
;Select the styleInteractive
. . . . . . . . . . . . . .,INT (cr)
Batch . . . . . . . . . . . . . . . . . .FIL (CT)Mode end . . . . . . ....

To Edit or Show the Data by “Batch Style” (cont.)n If “EOD” data is not programmed in batch data, the display will
show the following after two minutes.
When Edit mode:
5. Press q q q 1 Carriage Return ( 1 ) 1key.; None “EOD” In batch data
r-3; E> ‘.-;When Show mode:
; None 
“EOD” In batch data
l---l; s> 1-JWhen Edit mode:When Show mode:
0 To end the batch style, pressq R q 1 Carriage Return ( 1 ) 1
key.
0 To continue the batch style, press the
q q q 1 Carriage Return ( 1 ) 1 key and repeat step 3.
0 If...

1. Set a floppy disk to the drive of a data terminal equipment.
2. UTo chanqe or proqram a data
0 Enter the command (Main command, Subcommand) and
parameter corresponding to the feature that you want to
change as the way on page 3-9 “Editing or Programming”.
0 When change the other feature, repeat step 0.
O After entering all the data, enter “EOD”.
UTo confirm a data
0 Enter the command (Main command, Subcommand)
corresponding to the feature that you want to confirm as the
way on page 3-12 “Showing”.
0...

c
To Edit or Show the Data by “Batch Style” (cont.)(To recognize the made data)
If q is entered in the first line, the line will not be executed when abatch data is sent to the 
KX-Ti 23211 from a data terminal
equipment.
If the title of the change contents are entered in the line as following,
it will be useful when use it later because of the recognition of the
contents.
02s I 65 I 1r-------------------------,‘1. DATA=‘88. 8. 37. (WED)SET11rl------------------------r
04s I 8808373 I 1
EOD 1To show the...

Edit / Show Mode Map
I-;>INT
s
; Select the style
;Interactive . . . . . INT (cr)
;Batch . . . . . . . FIL (cr)
;Mode end . . . . . END (cr)
j j Ftyctive style startb
rI
/ j lgactive style startp(Interactive process)
‘7)) j B~~~~$fi~~~ batch data> I- (Batch process)
3- I/.0 

c
To Dump the Data
1 .Press them m IpI 1 Carriage Return ( 1 ) 1 key.
I; > dmp
I; Dump mode startI
I
l---l; p> L-1n If you wish to know the effective commands which can be used on
this mode, enter the “HLP” command.
; P> hlp
; Select the item
..............................
IAlIALL (cr)..........................
FSystemSYS (cr)
ICO. trunk........................COT (cr)
,Ext..............................EXT (cr)
IDSS console.....................DSS (cr)
........................DoorphoneDOR (CT)...