Panasonic Kx-T123211d Installation Manual

Setting 
Lift handset 
or press 
SP-PHONE 
To cancel 
Dial “76” 
Enter Enter 
Dial 
Dial 
Dial “#” Hang up or 
hour 
+ minute + “O” or ‘6,” + U,” or “2” 
press 
(01 through 1:). 
(00 through 59) 
“0” 
: for AM 
“1” : only one day SP-PHONE 
“1” : for PM I[ “2” : every day 1 
Lift handset 
Dial “762#” 
or press 
SP-PHONE 
To Confirm the setting time 
Hang up or 
press 
SP-PHONE 
Lift handset 
or press 
SP-PHONE Dial “763#” 
Hang up or 
press 
SP-PHONE 
Description 
If a time is set, an Alarm tone will...

Dial Dial “*#” Dial 
phone 
number phone 
number 
Description 
When the dialing mode is required to change a 
pulse mode to a tone mode in one dialing 
sequence, this feature is used. 
(e.g.computer-accessed long distance 
service) 
Operation 
1. Dial the phone number. (pulse mode) 
2. Dial (*#) 
3. Dial the phone number. (tone mode) 
Conditions 
l When you dial using this feature,you must 
use the line set to a pulse mode. 
Phone number after dialing”* # ” will 
change to tone mode. 
Example:Computer -...

Description 
Lamp indicators corresponding to the status of 
the CO (Central Office), the ICM (Intercom) and 
DSS (Direct Station Selection) buttons. ’ 
0 
Explanation 
ICM indicator liaht 
Light Status 
off 
on 
slow flashing 
flashing in 
groups of 2 
quick flashing idle 
0 in use for intercom 
0 in use for CO line 
to which the CO line 
number is not 
assigned. 
on hold 
0 When a call on CO line 
which the CO line 
number is not assigned 
is transfered to CO line. 
0 on exclusive hold 
0 receiving a...

Description 
In the event of a power failure each CO will be 
connected to assigned extension. 
CO1 will be assigned to extension of jack number 01. 
CO2 will be assigned to extension of jack number 02. 
CO5 will be assigned to extension of jack number 09. 
CO6 will be assigned to extension of jack number 10. 
CO9 will be assigned to extension of jack number 
17. 
CO10 will be assigned to.extension of jack number 18. 
Operation 
l If extension of jack number 01,02,09, 10, 17 
and 18 is connected with a...

Station Programming 
To Program 
l Be sure the handset is in the cradle and the SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary telephone to “PROGRAM”. 
Paging All Extensions (Dial 330). 
Press Dial “330” 
Press 
PROGRAMMABLE MEMORY .._..._... FEATURE 
After programming all the system features, return the MEMORY switch to the “SET” position. 
To Access 
I I I I __ 
I -r Lift handset Press Confirmation Page 
or press PROGRAMMABLE tone of 1 beep 
SP-PHONE FEATURE will be heard...

Prime Line Preference-Outgoing 
l Be sure the handset is in the cradle and the SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary telephone to “PROGRAM”. 
Setting To cancel 
Dial “13” Dial Press Dial “11” 
Press 
CO number MEMORY 
MEMORY 
(01 through 12) 
l After programming “Prime Line Preference-Outgoing” mode, return the MEMORY switch to the 
“SET” position. 
Dialing through CO line 
Lift handset 
or press 
SP-PHONE Wait for 
CO. dial tone Dial 
phone 
number 
Description 
You can...

Idle Line Preference-Outgoing 
l Be sure the handset is in the cradle and the SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary telephone to “PROGRAM”. 
Setting 
[r;li pi 
Dial “12” 
Press 
MEMOBY 
To cancel 
pq 61. 
Dial “11” 
Press 
MEMORY 
l After programming “Idle Line Preference-Outgoing” mode, return the MEMORY switch to the 
“SET” position. 
Dialing through CO line 
1..1;9:il pfl 
Lift handset Wait for 
or press CO. dial tone ~~~~~rle 
SP-PHONE 
Description 
You can access any...

Prime Line Preference-Incoming 
l Be sure the handset is in the cradle and the SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary telephone to “PROGRAM”. 
Setting To cancel 
Press 
Dial “22” 
CO number MEMORY Press 
(01 through 12) MEMORY 
l After programming “Prime Line Preference-Incoming” mode, return the MEMORY switch to the 
“SET” position. 
To answer 
Lift handset 
or press 
SP-PHONE 
Description To answer 
Lift the handset or press the SP-PHONE 
button.  When incoming calls from...

No Line Preference- tncoming 
l Be sure the handset is in the cradle and the SP-PHONE button is off. 
o Set the MEMORY switch of the proprietary telephone to 
“PROGRAM”. 
Setting To cancel 
I 1 1 
AUTO 1 
FY MEMORY 
Dial “21 ‘I 
Press 
MEMORY Press 
MEMORY 
l After programming “No Line Preference-Incoming”, return the MEMORY switch to the 
“SET” position. 
To answer 
Lift handset 
or press 
SP-PHONE Press 
CO whose 
indicator is 
quickly flashing 
Description To answer 
If programmed for the No Line...

To Change into Other CO Button 
To Assign into Trunk Group Access Button 
l Be sure the handset is in the cradle and the 
SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary 
telephone to 
“PROGRAM”. 
l Be sure the handset is in the cradle and the 
SP-PHONE button is off. 
l Set the MEMORY switch of the proprietary 
telephone to 
“PROGRAM”. , . 
Press CO 
which you 
want to 
change into 
different 
CO button Dial “0” 
Dial Press 
CO number MEMORY 
which is 
set newly 
(01 through 12) 
l...