Panasonic Kx P8410 Operating Instructions Manual

							141
Turn off the printer and
the computer, then turn
them on again. Print the
document again. SCSI Error!! Time Out
occurred.
Unable to Allocate Memory The computer’s
internal memory for
printing is insufficient. The printer is not
responding.
Error messagePossible causeRecovery
Care and Maintenance
BClose all applications
except for the one
which controls the
printer, then print
again.
BTurn off the
computer, then turn it
on again.
Printing aborted for
occurred SCSI error.An illegal error has
occurred.BConfirm the SCSI
board is correctly
installed in the
computer or cable is
correctly connected.
BTurn off the
computer, then turn it
on again.
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 134). SCSI board and its
driver are not installed
correctly. No ASPI managers were
found!!
One or more ASPI for DOS
managers are loaded which
do not support ASPI for
WIN16!!
Follow the procedure
below and disable the bi-
directional interface.
1. Double-click Status
display setup
icon in
KX-P8410 Utilities
program group.
2. Click Devicetab.
3. Click off Monitor
Printercheck box.
4. Click OK.
The Status Display
function becomes
ineffective. The printer does not print
correctly (not an error
message).The computer is not
properly communicating
with the printer.
Unable to Free Memory!! Re-boot Windows.Something happened to
the memory environment
of Windows. 
						

							142
Care and Maintenance
Error messagePossible causeRecovery
*.DLL not found *.DLL function ErrorThe necessary file for
printing is not found.Reinstall the KX-P8410
software.
File ID not match!!
nSome application settings may take priority over the printer driver settings. Table file open error!!
Table file read error!!Resource DLL file is not
found. Check sum error!! 
						

							143
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
wnaspi32.dllwill be
installed or replaced
with a new version.
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 134).
The ASPI manager
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g. install wnaspi32.dll to
your windows (system
directory)]. The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer version
of ASPI for Windows.
Error messagePossible causeRecovery
ASPI Manager is not found.
Install ASPI for Windows.
(e.g. install wnaspi32.dll to
your windows (system
directory.)
Care and Maintenance
Can not find Panasonic KX-
P8410. Make sure that
Panasonic KX-P8410 is
connected to your PC by
SCSI, and then retry again.Correctly install SCSI
board and its driver.
(Refer to the manual of
the SCSI board.)
wnaspi32.dllwill be
installed or replaced
with a new version. SCSI board and its
driver are not installed
correctly.
BCable connection is
improper or printer is
not ready.
BThe terminator
setting is improper.
The ASPI for Windows
installed on this PC does
not have expected function.
Install newer version of
ASPI for Windows.SCSI board and its
driver are not installed
correctly.Perform the following
procedure.
1. Confirm that the
terminator is correctly
set.
2. Confirm that the
printer is ready.
3. Confirm that the
printer is correctly
connected with a
SCSI cable.
4. Turn off the
computer, then turn it
on again.
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows
Printer Driver For Windows 95 
						

							144
Follow the procedure
below to make the setting
active.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 printericon.
3. Click the File menu,
then click Properties.
4. Click Details tab and
Spool settings....
5. Click Enable bi-
directional support for
this printer, then click
OK.
Error messagePossible causeRecovery
Care and Maintenance
There was an error
writing to LPT1: for the
printer (Panasonic 
KX-P8410):
There was a problem
sending your document
to the printer. Make sure
the printer cable is
connected and the
printer is online. To
continue printing, click
retry. Windows will
automatically retry after
5 secondsConnect the printer
(parallel cable) correctly or
make the printer ready. Cable connection is
improper or the printer
is not ready. The Status Display
does not appear when
printing a document.The Status Display
function is not active
The printer does not print
correctly (not an error
message).The computer is not
properly communicating
with the printer.Follow the procedure below
and disable the bi-
directional interface.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 
icon.
3. Click the Filemenu, then
click Properties.
4. Click Detailstab and
Spool settings....
5. Click Disable bi-
directional support for
this printer, then click
OK.
The Status Display
function becomes
ineffective. 
						

							145
Care and Maintenance
Resource DLL file is not
found.Reinstall the KX-P8410
software. The necessary file for
printing is not found.
Can not load pclradj.dll
Table file open error!! Check sum error!!
File ID not match!!
Table file read error!!
Error MessageCorrective ActionPossible Cause
BClose all applications
except for the one which
controls the printer, then
print it again.
BTurn off the computer,
then turn it on again.
Print the document
again. Unable to Allocate
Memory!!The memory for
printing is insufficient.
BCable connection is
improper or the
printer is not ready.
BThe terminator
setting is improper. There was an error
writing to KXP8410GDI:
for the printer
(Panasonic KX-P8410):
The printer is not ready.
Make sure it is turned
on and online. To
continue printing, click
retry. Windows will
automatically retry after
5 secondsPerform the following
procedure.
1. Confirm that the
terminator is correctly
set.
2. Confirm that the printer
is ready.
3. Confirm that the printer
is correctly connected
with a SCSI cable.
4. Turn off the computer,
then turn it on again. 
						

							146
Care and Maintenance
Error messagePossible causeRecovery
Increase the hard disk
space.
If it is difficult to increase the
hard disk space or printing
error occurs even after
increasing the hard disk
space, change the spool
data format from EMF to
RAW by performing the
following steps.
However, RTA (Return To
Application: the length of
time between the start of
printing and the return of
control to an application) of
RAWis longer than that of
EMF.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 
icon.
3. Click the Filemenu, then
click Properties.
4. Click the Detailstab and
Spool settings....
5. Change the Spool data
formatto RAW, then
clickOK. Windows could not write
to the printer spool file.
Make sure your disk has
enough free space and
try again.Hard disk space is
insufficient.
nSome application settings may take priority over the printer driver settings. 
						

							147
Error writing to
KXP8410GDI: for : The printer command
is invalid. Do you wish to
retry or cancel the job?
Care and Maintenance
Error messagePossible causeRecovery
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows.SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dll will be
installed or replaced with a
new version.
For any other trouble related
to SCSI, refer to the SCSI
section of Care and
Maintenance ( 
+P. 134).
ASPI Manager is not
found. Install ASPI for
Windows. (e.g. install
wnaspi32.dll to your
system32 directory).SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dllwill be
installed or replaced with a
new version.
The ASPI for Windows
installed on this PC does
not have expected
function. Install newer
version of ASPI for
Windows.
The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer
version of ASPI for
Windows.
The ASPI for Windows
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g.install wnaspi32.dll to
your system32 directory]
Printer Driver For Windows NT 4.0
Separator page has
been set. When SCSI
port is used, Separator
page cannot be used.Cancel the Separator page
setting.
Error writing to LPT1: for
“Application name”: The
device is not ready. Do
you wish to retry or
cancel the job?Connect the printer (parallel
cable) correctly or make the
printer ready. Cable connection is
improper or printer is not
ready. 
						

							148
Care and Maintenance
System Process-Out of
Virtual Memory 
Your system is running
low on virtual memory.
Please close some
applications. You can
then start the System
option in the Control
Panel and choose the
Virtual Memory button to
create an additional
paging file or to increase
the size of your current
paging file.Your system is running
low on virtual memory.Increase the virtual memory
by following the procedure
below.
1. Click Start, Settings,
then click Control Panel.
2. Double click the System
icon.
3. Click the Performance
tab.
4. ClickChange....
5. Increase the value of
Initial Size [MB] and
Maximum Size [MB].
6. Click Set.
7. Click OK.
8. Click Close.
9. Click Yesin the System
Settings Changedialog,
then restart your
computer.
If the same error message
appears after increasing the
virtual memory, repeat the
steps above.
Error messagePossible causeRecovery
Perform the following
procedure.
1. Confirm that the
terminator is correctly set.
2. Confirm that the printer is
ready.
3. Confirm that the printer is
correctly connected with
a SCSI cable.
4. Turn off the computer,
then turn it on again. BCable connection is
improper or printer is
not ready.
BThe terminator setting
is improper. Error writing to “Port
name” for “Application
name”: The request could
not be performed
because of an I/O device
error. Do you wish to retry
or cancel the job? 
						

							149
BThe printer was
turned on after
turning on the
computer.
BThe terminator
setting is improper.
BSCSI setting or
cable connection is
improper. The necessary file is
not installed in the
computer.
Error messagePossible causeRecovery
Care and Maintenance
Not Detect. Turn off the printer and the
computer, then turn them
on again. If the trouble still
remains, confirm the
following points.
BThe terminator is
correctly set.
BThe SCSI board is
correctly installed in the
computer.
BThe system is correctly
connected with SCSI
cables.
BEach SCSI device has a
different ID Number. Invalid LPT Port.
SCSI board is not
correctly set.Correctly set the SCSI
board in the computer.
(Refer to the manual of the
SCSI board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 134). Unavailable LPT port is
selected when using
Windows 3.1.
No ASPI managers are
loaded. This typically
occurs when a DOS
ASPI manager is not
resident in memory.Reinstall the KX-P8410
software.
Select the other available
LPT port by following the
procedure below.
1. Double click the Main
icon.
2. Double click the Control
Panelicon.
3. Double click the Printers
icon.
4. Click Connect....
5. Click the other port, then
click OK.
6. Click Close.
Load Library Error!,
File Open Error!or
Install Error!appears
and Status Display does
not appear.
Status Display
ASPI for Win 16 or 32
could not properly
initialize itself. This may
be caused by a lack of
system resources.Lack of system
resources, or other
trouble related to
SCSI.Close some application
and retry. For any other
trouble related to SCSI,
refer to the SCSIsection of
Care and Maintenance 
( +P. 134). 
						

							150
Confirm that the SCSI
board is correctly installed
in the computer and it is
set correctly. (Refer to the
manual of the SCSI
board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 134). SCSI board is not set
correctly.
Unavailable LPT port is
selected when using
Windows 3.1. There isn’t available
LPT Port.
Error messagePossible causeRecovery
Care and Maintenance
SCSI device can not be
used. Because ASPI dll
file is not exist or
doesn’t match.SCSI board is not
installed correctly in
the computer and/or it
is not set correctly. This ASPI manager
does not support this
mode of Windows. You
typically see this error
code when running
Windows in Real ModeSCSI board is not set
correctly.Restart Windows in
Enhanced mode.
Select an available LPT
port by following the
procedure below.
1. Double click the Main
icon.
2. Double click the Control
Panelicon.
3. Double click the Printers
icon.
4. Click Connect....
5. Click the other port, then
click OK.
6. Click Close.
One or more ASPI for
DOS managers are
loaded which do not
support ASPI for Win16
or 32.Correctly set the SCSI
board in the computer.
(Refer to the manual of the
SCSI board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 134).