Panasonic Kx P7305 Operating Instructions Manual

Settings and Printing
Network Network Maintenance and Spec.
Appendix
88
■Troubleshooting when installing the printer software
TroublePossible CauseCorrective Action
Printer software cannot be 
installed in a computer.You do not log on the 
computer as an 
Administrator in Windows 
NT 4.0, Windows 2000, 
Windows XP or Windows 
Server 2003.Log on the computer as an 
Administrator.
A document is not printed 
through the server 
computer.You have no authority to 
print.Contact the administrator to 
register...

Settings and Printing
Network Network Maintenance and Spec.
Appendix
89
•General(see below)
•TCP/IP(see page 90)
•NetWare(see page 91)
•AppleTalk(see page 92)
•SMB(see page 92)
•SNMP(see page 93)
•Printer Port(see page 94)
■General
Configuration Parameters
NameFactory DefaultDescription
Change root 
passwordNULL Password for Administrator. It is used for 
authentication when entering Network 
Setup Tool.
Use HP JetAdmin ENABLE Enables or disables to use HP's utility 
JetAdmin/Web JetAdmin. 

Settings and Printing
Network Network Maintenance and Spec.
Appendix
90
■TCP/IP
NameFactory DefaultDescription
Use TCP/IP Protocol ENABLE Enables or disables TCP/IP protocol.
Use DHCP/BOOTP ENABLE Enables or disables DHCP/BOOTP. When 
enabled, KX-P7310 gets an IP Address 
from the DHCP/BOOTP server while 
booting. To use this function DHCP/BOOTP 
server must exist on the network.
Use RARP ENABLE Enables or disables RARP. RARP is a 
protocol which obtains IP Address from 
RARP server. When using this...

Settings and Printing
Network Network Maintenance and Spec.
Appendix
91
■NetWare
NameFactory DefaultDescription
Use NetWare 
ProtocolENABLE Enables or disables NetWare printing.
Frame Type 802.2 Sets default Frame type used by KX-P7310. 
If KX-P7310 does not work with the frame 
type, it will be automatically changed to 
different type.
Printer  Name MLPxxxxxx-Printer Sets printer name registered to the NetWare 
server. This name must be same as the 
printer name registered to the NetWare 
server....

Settings and Printing
Network Network Maintenance and Spec.
Appendix
92
■AppleTalk
■SMB
NameFactory DefaultDescription
Use AppleTalk 
ProtocolENABLE Enables or disables AppleTalk protocol for 
KX-P7310. 
Printer Name KX-P7310-xxxxxx Sets the AppleTalk printer name. The name 
set here can be seen from Chooser.
Zone Name * Sets zone name to which KX-P7310 
belongs. If blank, KX-P7310 will 
automatically belong to the zone name 
where the AppleTalk router is set.
NameFactory DefaultDescription
Use NetBEUI...

Settings and Printing
Network Network Maintenance and Spec.
Appendix
93
■SNMP
NameFactory DefaultDescription
Authentic 
Community****** Sets SNMP authentic community name. 
This community name is authenticated 
when receiving SNMP Set Request.
Use Authentic Trap DISABLE Enables or disables authentic TRAP.
TRAP Community public Enters TRAP community name. This name 
will be used when the printer executes a 
TRAP.
TRAP Address 0.0.0.0 Enters the TRAP address. The TRAP 
address is disabled if the IP Address...

Settings and Printing
Network Network Maintenance and Spec.
Appendix
94
■Printer Port
NameFactory DefaultDescription
lp Port
BOJ String 
(MJL String)NULL Sets the MJL String that will be sent before 
sending a print job to the direct output port 
(lp).
EOJ String 
(MJL String)NULL Sets the MJL String that will be sent at the 
end of a print job to the direct output port 
(lp).
euc/sjis Port
BOJ String NULL Sets the string sent before sending the 
printing job to the output port via Kanji filter 
(sjis,...