Panasonic Kx P7305 Operating Instructions Manual

Settings and Printing
Network Network Maintenance and Spec.
Setup in Windows
38
[For Windows NT 4.0 / Windows 2000 / Windows XP / 
Windows Server 2003]
1Click [Start], move the pointer to Settings, then click Printers.
The Printers window is displayed.
• For Windows XP Professional / Windows Server 2003, click [Start], then click or 
double click Printers and Faxes.
• For Windows XP Home, click [Start], click Control Panel, click Printers and Other 
Hardware icon, then click Printers and Faxes icon....

Settings and Printing
Network Network Maintenance and Spec.
Setup in Windows
39
7Click on the Print using IPP check button and click [Next >].
8Click either the Connect using a modem and telephone line or 
Connect using a local area network check button. Click [Next >].
• If you select Connect using a modem and telephone line, proceed to step 10.
• If your computer is not eqipped with a dial-up adapter, this selection window is not 
displayed. Proceed to step 9.
9Click either the Do not print using a...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Windows
40
This enables you to use the HP JetDirect port printing using the HP JetAdmin software. 
TCP/IP or IPX/SPX protocol is used for printing.
HP JetDirect Port Printing using TCP/IP or IPX/SPX
in Windows 

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
41
KX-P7310 Setup Utility uses TCP/IP. You need to set up AppleTalk and TCP/IP on your 
computer and printer. The printer does not work with AppleTalk Phase1.
Step 1: Setting up AppleTalk and TCP/IP on your computer
[For Mac OS 8.5 - Mac OS 9.2]
See page 42 for Mac OS X 10.1 - Mac OS X 10.2.
1Select Control Panels from the Apple menu, then double click 
AppleTalk icon.
2Select Ethernet from the Connect via box.
3Close the...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
42
[For Mac OS X 10.1 - Mac OS X 10.2]
1Click System Preference... from the Apple menu and click Network 
icon.
The Network window is displayed.
2Select Built-in Ethernet from Show menu.
3Click the TCP/IP tab.
4Assign the IP Address to your computer or use the DHCP server for TCP/
IP setting.
• To setup the TCP/IP, check with your network administrator.
5Click the AppleTalk tab.
6Be sure the Make AppleTalk Active check box is...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
43
Step 2: Setting up TCP/IP on the printer
You need to set the IP Address, Subnet Mask and Default Gateway for the printer. Set them by 
using one of the following two methods. You may need to contact your network administrator 
to select the best way.
• Using the DHCP server (see below)
• Using the Network Setup Tool (see page 44)
NOTE
• You can also setup the printer using BOOTP or RARP.
[A] Using the DHCP server
If the...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
44
[B] Using the Network Setup Tool (Mac OS 8.5 - Mac OS 9.2)
Network Setup Tool can operate in the Classic environment only. When using it in Mac OS X 
10.1 or Mac OS X10.2, use it in the Classic environment.
If the administrator manages the IP Address, contact them to confirm the values before the 
installation. If not, set the unique value that is not used by another devices on the network. 
Refer to the example shown...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
45
7Click the KX-P7310 printer you want to set up, click Setup menu and then 
select Network Setup....
NOTE
• When several printers are listed, select the printer using the MAC address. You can 
obtain the number (hexadecimal six digits) from the label near the network interface 
connector or by printing a configuration page (press PRINT/RESET button more than 
2 seconds and less than 5 seconds).
• If a password is set in the...

Settings and Printing
Network Network Maintenance and Spec.
Setup in Macintosh
46
10Click [OK].
11Click Setup menu and click Restart the printer.
12Click [OK] to restart the printer.
13Click the printer assigned the IP Address and click Network Setup... from 
the Setup menu.
• If a password is set, you must enter the password and click [OK].
14Click the AppleTalk icon.
15Confirm the Use AppleTalk Protocol check box is checked.
• If needed, change the Printer Name and enter the Zone Name.
16Click...

Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
47
This chapter explains how to setup a client computer to print via a NetWare server.
Perform the following steps:
Step 1: Setting up the printer and server
Step 2: Setting up the client
Step 1: Setting up the printer and server
There are four ways of setup.
•[A] Using NDS (Novell Directory Service) - PSERVER mode(see page 48)
•[B] Using NDS - RPRINTER (NPRINTER) mode(see page 53)
You may need to check with your network...