Panasonic Kx Mb271 Operating Instructions Manual

							1. Introduction and Installation
11
For assistance, please visit http://www.panasonic.com/help
8Close the top cover until locked.
Caution:
LTo prevent injuries, be careful not to put your 
hands under the top cover.
To replace the toner cartridge and the drum unit
When the display shows the following, replace the toner 
cartridge.
TONER LOW
TONER EMPTY
LTo check the drum life and quality, please print the 
printer test list (page 84) and refer to page 86 for 
information on the drum life. If printing quality is still 
poor or “REPLACE DRUM” appears on the display, 
replace the toner cartridge and drum unit.
LTo ensure that the unit operates properly, we 
recommend the use of Panasonic toner cartridge 
(Model No. KX-FAT92) and drum unit 
(Model No. KX-FAD93). See page 6 for accessory 
information.LTo maintain print quality and machine life, we 
recommend you to clean slots and openings (page 3) 
and the inside of the unit (page 80, 83) when 
replacing the toner cartridge and/or drum unit.
Waste disposal method
Waste material should be disposed of under conditions 
which meet all national and local environmental 
regulations.
Toner save feature 
If you want to reduce toner consumption, set the toner 
save setting to ON (feature #482 on page 51). The toner 
cartridge will last approximately 40 % longer. This 
feature may lower the print quality.
MB271-781-PFQX2722ZA-OI-en.book  Page 11  Tuesday, May 22, 2007  5:20 PM 
						

							1. Introduction and Installation
12
For assistance, please visit http://www.panasonic.com/help
1.6 Output tray
Pull the output tray extender (1) forward gently until it 
clicks into place, then press the center part of the 
extender (2) to open.
Note:
LDo not place the unit in an area where the output tray 
may be easily bumped into.
LThe output tray can hold up to approximately 150 
sheets of printed paper. Remove the printed paper 
before the output tray becomes full.
If the top part of the extender is detached
1.With the top part of the extender in the open position, 
insert the tab (1) into the left hole (2) of the 
extender.
2.Slide the other tab (3) into the right hole (4) of the 
extender from below until it clicks into place.
2
1
2
1
4
3
MB271-781-PFQX2722ZA-OI-en.book  Page 12  Tuesday, May 22, 2007  5:20 PM 
						

							1. Introduction and Installation
13
For assistance, please visit http://www.panasonic.com/help
If the extender is detached
1.Line up the extender (1) with the left side of the 
output tray. Make sure that the triangles (2) match, 
to attach the extender correctly.
2.Snap the extender (3) into the unit by pushing down 
the right side of the extender.1.7 Recording paper
The paper input tray unit can hold:
– Up to 250 sheets of 60 g/m2 to 75 g/m2 (16 lb. to 20 
lb.) paper.
– Up to 230 sheets of 80 g/m
2 (21 lb.) paper.
– Up to 200 sheets of 90 g/m2 (24 lb.) paper.
LPlease refer to page 85 for information on recording 
paper.
LThe unit is set for printing letter size paper by 
default. If you want to use A4 or legal size paper, 
change the setting (feature #380 on page 50).
1Pull the paper input tray (1) until it clicks into place, 
then pull it completely out, lifting the front part of the 
tray.
2Before loading a stack of paper, fan the paper to 
prevent paper jams.
1
2
3
1
MB271-781-PFQX2722ZA-OI-en.book  Page 13  Tuesday, May 22, 2007  5:20 PM 
						

							1. Introduction and Installation
14
For assistance, please visit http://www.panasonic.com/help
3Load the paper, print-side up (2).
Important:
LPush and lock the plate (3) in the paper input 
tray, if it is lifted.
4Adjust the recording paper guides. Pinch the front 
side of the recording paper guide (4), then slide it to 
match the paper size mark. Pinch the right side of 
the recording paper guide (5), then slide it to adjust 
the width to the size of the recording paper.
LMake sure that the recording paper is under the 
paper limit mark (6), and the paper should not 
be loaded over the snubbers (7).
5Insert the paper input tray to the unit, lifting the front 
part of the tray. Then push it completely into the unit.
Note:
LIf the paper is not loaded correctly, re-adjust the 
paper guides, or the paper may jam.
LIf the paper input tray does not close, the plate in the 
paper input tray may be lifted. Push the paper and 
make sure that the paper is laid flat in the paper input 
tray.
Caution for the paper input tray
LDo not drop the paper input tray.
LHold the paper input tray with both hands when 
removing or installing. The paper input tray 
weighs approximately 2 kg (4.4 lb.) when the 
recording paper is fully installed.
3
2
7
6
5
4
Approx. 2 kg (4.4 lb.)
MB271-781-PFQX2722ZA-OI-en.book  Page 14  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
15
For assistance, please visit http://www.panasonic.com/help
2 Preparatio n 2For a ssistanc e, plea se visit http://www.p ana sonic.co m/he lp
Con nections  an d  Setup
2.1 Connections
Caution:
LWhen you operate this product, the power outlet 
should be near the product and easily 
accessible.
* The pictured model is KX-MB781.Note:
LIf any other device is connected to the same 
telephone line, this unit may disturb the network 
condition of the device (KX-MB781 only).
Using surge protectors
LThe warranty does not cover damage due to power 
line surges or lightning. For additional protection, we 
recommend using surge protectors (9).
If the unit shares a single telephone line with a DSL 
service (KX-MB781 only)
Fax transmission/reception may be disturbed, noise 
interference may be heard during telephone 
conversations, or Caller ID (page 45) may not function 
properly. A filter to prevent this is provided by your 
provider. Please attach the filter (j) to the telephone 
line cord of the unit.
* The pictured model is KX-MB781. 1Power cord
LConnect to a power outlet
(120 V, 60 Hz).
2Telephone line cord*1
LConnect to a single telephone line jack (RJ11).
3[EXT] jack*1
LYou can connect an answering machine or an 
extension telephone. Remove the stopper if 
attached.
4Answering machine (not included)
*1
5Handset unit (optional) connection jack*1
LYou can connect the optional handset unit (page 
62). Remove the seal if attached.
6Network router/Network hub (not included)
*1
LAlso connect networked computers.
7To the internet*1
8LAN cable (not included)*1
LTo assure continued emission limit compliance, 
use only shielded LAN cable (category 5 straight 
cable).
*1 KX-MB781 only
Important notice for the USB connection
LDo NOT connect the USB cable until prompted by 
the Multi-Function Station (page 22).
4
7 128
3
6
9
5
9
j
MB271-781-PFQX2722ZA-OI-en.book  Page 15  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
16
For assistance, please visit http://www.panasonic.com/help
2.2 Dialing mode (KX-MB781 
only) 
If you cannot dial (page 35), change this setting 
according to your telephone line service.
1{MENU} i {#}{1}{2}{0}
DIALING MODE
=TONE [V^]
2Press {1} or {2} to select the desired setting.
{1} “PULSE”: For rotary/pulse dial service.
{2} “TONE” (default): For tone dial service.
3{SET}
4Press {MENU} to exit.
2.3 Selecting the operation mode 
(Scan/Copy) (Fax: KX-MB781 
only)
You can select the desired mode by pressing one of the 
following buttons.
* The pictured model is KX-MB781.
–{SCAN}: Select this mode when using the unit as a 
scanner for the computer (page 27).
–{COPY}: Select this mode when using the unit as a 
copier (page 30).
–{FA X} (KX-MB781 only): Select this mode when 
using the unit as a fax machine (page 35).
Note:
LThe default operation mode is the copy mode.
LYou can change the default operation mode (feature 
#463 on page 50) and the timer before returning to 
the default operation mode (feature #464 on page 
51) (KX-MB781 only).
{SET}
{MENU}
MB271-781-PFQX2722ZA-OI-en.book  Page 16  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
17
For assistance, please visit http://www.panasonic.com/help
Doc ument Requirements
2.4 Setting the original
2.4.1 Using the scanner glass
1
Open the document cover (1).
2Place the document FACE DOWN on the scanner 
glass (2), aligning the top left of the document with 
the corner to which the m mark points.
3Close the document cover.
Note:
LConfirm that there are no documents in the auto 
document feeder.
LPlace the original onto the scanner glass gently and 
do not press down too firmly to avoid malfunction.
LIf the original is a thick book, do not close the 
document cover.
LCheck that ink, paste or correction fluid has dried 
completely.
LEffective scanning area is as follows:
Effective scanning area
LShaded area will be scanned.
2.4.2 Using the auto document feeder
1
Insert the document (up to 20 pages) FACE UP into 
the feeder until a single beep is heard.
2Adjust the width of the document guides (1) to fit 
the actual size of the document.
Note:
LConfirm that there are no documents on the scanner 
glass.
LCheck that ink, paste or correction fluid has dried 
completely.
LRemove clips, staples or other fasteners.
LDo not set the following types of documents: (Make a 
copy of the document using the scanner glass and 
set the copy instead.)
– Chemically treated paper such as carbon or 
carbonless duplicating paper
– Electrostatically charged paper
– Badly curled, creased or torn paper
– Paper with a coated surface
– Paper with printing on the opposite side that can 
be seen through the other side, such as 
newsprint
LThe total height of the documents when laid flat, 
must be less than 4 mm (
5/32). If the documents 
exceed the capacity of the auto document feeder, 
they may fall or cause a jam in the feeder.
LTo set a document with a width of less than 210 mm 
(8
1/4), we recommend using the scanner glass to 
copy the original document onto A4 or letter-sized 
paper, then setting the copied document.
LDo not set documents that do not satisfy the 
requirements of size and weight. Make a copy of the 
document using the scanner glass and set the copy.
LAvailable document size, document weight and 
effective scanning area are as follows:
1
2
208 mm
(83/16)
287
 mm
(115/16)5 mm
 (3/16)5 mm
 (3/16)
 4 mm
 (5/32)
 4 mm
 (
5/32)
1
MB271-781-PFQX2722ZA-OI-en.book  Page 17  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
18
For assistance, please visit http://www.panasonic.com/help Minimum document size
Maximum document size
Effective scanning area
LShaded area will be scanned.
Document weight
LSingle sheet:
60 g/m
2 to 75 g/m2 (16 lb. to 20 lb.)
LMultiple sheets:
60 g/m
2 to 75 g/m2 (16 lb. to 20 lb.)
H e lp  Bu tt on
2.5 Help function (KX-MB781 
only)
The unit contains helpful information on the following 
topics which can be printed for reference purposes, as 
follows:
–“BASIC SETTINGS”
–“FEATURE LIST”
–“DIRECTORY”
–“FAX SND/RCV”
–“COPIER”
–“Q and A”
–“ERRORS”
–“REPORTS”
–“CALLER ID”
1Press {MENU} repeatedly to display “HELP”.
2Press {} repeatedly to display the desired 
item. i {SET}
3Press {MENU} to exit.
128 mm
(5)
128 mm
(5)
600 mm
(23 
5/8) 
216 mm
(8 1/2)
216 mm(8 1/2)
208 mm(8 3/16)
 4 mm(5/32) 4 mm(5/32)
 5 mm(3/16)
 5 mm(3/16)
{SET}{}
{MENU}
MB271-781-PFQX2722ZA-OI-en.book  Page 18  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
19
For assistance, please visit http://www.panasonic.com/help
Vol um e
2.6 Adjusting volume (KX-MB781 
only)
Before adjusting volume, set the operation mode to fax 
mode (page 16).
Ringer volume
While the unit is idle, press {V} or {^}.
LIf there are any documents in the document 
entrance, you cannot adjust the volume. Confirm that 
there are no documents in the entrance.
To turn the ringer OFF
Press {V} repeatedly to display “RINGER OFF= OK?”. 
i {SET}
LThe unit will not ring.
LTo turn the ringer back ON, press {^}.
Ringer pattern
LYou can select one of 3 ringer patterns (feature #161 
on page 50).
Monitor volume
While using the monitor, press {V} or {^}.
Initial Programming
2.7 Date and time (KX-MB781 
only)
1{MENU} i {#}{1}{0}{1} i {SET}
M:|
01/D:01/Y:07
TIME: 12:00AM
2Enter the current month/date/year/hour/minute by 
selecting 2 digits for each.
Example: August 10, 2007 10:15 PM (12 hour 
clock format)
1.Press {0}{8} {1}{0} {0}{7} {1}{0} {1}{5}.
M:|
08/D:10/Y:07
TIME: 10:15AM
2.Press {*} repeatedly to select “PM”.
3{SET}
4Press {MENU} to exit.
Note:
LThe other party’s fax machine will print the date and 
time on the top of each page you send according to 
your unit’s date and time setting.
LAfter setting the date and time, if the unit is in the 
copy mode, change it to the fax mode by pressing 
{FA X}. You can check your unit’s date and time 
setting on the display.
To correct a mistake
Press {} to move the cursor to the incorrect 
number, and make the correction.
If you have subscribed to a Caller ID service
The date and time will be automatically set according to 
the received caller information.
LIf the time has not previously been set, Caller ID will 
not adjust the clock.
LYou can turn this feature OFF (feature #226 on page 
50).
{V}{^}{SET}{}{SET}{FAX}
{MENU}
MB271-781-PFQX2722ZA-OI-en.book  Page 19  Tuesday, May 22, 2007  5:20 PM 
						

							2. Preparation
20
For assistance, please visit http://www.panasonic.com/help
2.8 Your logo (KX-MB781 only)
You can program your logo (name, company name, etc.) 
so that it appears on the top of each page sent.
1{MENU} i {#}{1}{0}{2} i {SET}
LOGO=|
2Enter your logo, up to 30 characters (see page 60 for 
character entry). i {SET}
3Press {MENU} to exit.
To correct a mistake
Press {} to move the cursor to the incorrect 
character, and make the correction.
LTo erase all characters, press and hold {STOP}.
2.9 Your fax number (KX-MB781 
only)
You can program your fax number so that it appears on 
the top of each page sent.
1{MENU} i {#}{1}{0}{3} i {SET}
NO.=|
2Enter your fax number, up to 20 digits.
LTo enter a “+”, press {*}.
LTo enter a space, press {#}.
LTo enter a hyphen, press {FLASH}.
LTo erase a number, press {STOP}.
3{SET}
4Press {MENU} to exit.
To correct a mistake
Press {} to move the cursor to the incorrect 
number, and make the correction.
LTo erase all numbers, press and hold {STOP}.
{}
{SET}
{MENU}{STOP}
{}
{SET}{FLASH}
{MENU}{STOP}
MB271-781-PFQX2722ZA-OI-en.book  Page 20  Tuesday, May 22, 2007  5:20 PM