Panasonic Kx Mb271 Operating Instructions Manual

9. Programmable Features
51
Setting the default operation 
mode timer
{#}{4}{6}{4}
(KX-MB781 only)To set the timer before returning to the default operation mode (feature #463).
{0} “OFF”: Deactivates this feature.
{1} “30s”: 30 seconds
{2} “1min” (default): 1 minute
{3} “2min”: 2 minutes
{4} “5min”: 5 minutes
Setting toner save feature
{#}{4}{8}{2}{0} “OFF” (default): Deactivates this feature.
{1} “ON”: The toner cartridge will last longer.
Note:
LThis feature may lower the print quality by reducing...

9. Programmable Features
52
9.3 Fax features (KX-MB781 only)
Feature/CodeSelection
Printing a confirmation report
{#}{4}{0}{1}{0} “OFF”: Confirmation reports will not be printed.
{1} “ON”: A confirmation report will be printed after every fax transmission.
{2} “ERROR” (default): A confirmation report will be printed only when fax 
transmission fails.
Setting the journal report to 
print automatically
{#}{4}{0}{2}{0} “OFF”: The unit will not print a journal report, but will keep a record of the 
last 30...

9. Programmable Features
53
Setting the Error Correction 
Mode (ECM)
{#}{4}{1}{3}This feature is available when the sending / receiving fax machines are ECM 
compatible.
{0} “OFF”: Deactivates this feature.
{1} “ON” (default): If there is an error during fax transmission / reception, the 
unit will support the communication.
Setting the connecting tone
{#}{4}{1}{6}If you often have trouble when sending faxes, this feature allows you to hear 
connecting tones: fax tone, ring back tone and busy tone. You...

9. Programmable Features
54
Receiving a fax into the 
computer
{#}{4}{4}{2}If you wish to receive a fax into the computer, activate this feature and run [PC 
FA X] from Multi-Function Station.
{0} “OFF” (default): Deactivates this feature.
{1} “ALWAYS”: If the unit recognizes the connection to the computer, it will 
transfer a received document to the computer. If the unit cannot recognize the 
connection, it will store a received document in the memory once, then transfer 
the data after recognition of...

9. Programmable Features
55
9.4 Copy features
9.5 PC print features
Feature/CodeSelection
Changing the default copy 
resolution
{#}{4}{6}{1}To change the default resolution setting for copying.
{1} “TEXT/PHOTO”: For documents containing both text and photographs.
{2} “TEXT” (default): For documents containing only text.
{3} “PHOTO”: For documents containing photographs, shaded drawings, etc.
Holding the previous page 
layout setting
{#}{4}{6}{7}{0} “DISABLED” (default): Deactivates this feature.
{1}...

9. Programmable Features
56
9.6 Scan features
Feature/CodeSelection
Setting the scan mode for 
Push Scan
{#}{4}{9}{3}{1} “VIEWER” (default): The scanned image will be displayed in the [Multi-
Function Viewer] window.
{2} “FILE”: The scanned image will be saved as a file.
{3} “E-MAIL”: The scanned image will be saved for e-mail attachment.
{4} “OCR”: The scanned image will be displayed in the OCR window.
Holding the previous 
scanning parameter for Push 
Scan
{#}{4}{9}{4}{0} “DISABLED” (default):...

9. Programmable Features
57
9.7 LAN features (KX-MB781 only)
Feature/CodeSelection
LAN setting with a DHCP 
server
{#}{5}{0}{0}{0} “DISABLED”: Deactivates this feature.
{1} “ENABLED” (default): The following will be allocated automatically using a 
DHCP (Dynamic Host Configuration Protocol) server.
– IP address
– Subnet mask
– Default gateway
Setting the IP address for the 
LAN connection
{#}{5}{0}{1}This feature is available when feature #500 is deactivated.
1.{MENU} i {#}{5}{0}{1} i {SET}
2.Enter the...

9. Programmable Features
58
Setting HTTPD for the LAN 
connection
{#}{5}{3}{4}{0} “DISABLED”: Denies access to the web browser.
{1} “ENABLED” (default): Allows access to the web browser.
Feature/CodeSelection
MB271-781-PFQX2722ZA-OI-en.book  Page 58  Tuesday, May 22, 2007  5:20 PM 

9. Programmable Features
59
9.8 Network features (KX-MB781, LAN connection only)
These features can be programmed only by using the web browser.
Note:
LSee the following sections for details on these related features:
– Change password (feature #155 on page 50)
– DHCP mode (feature #500 on page 57)
– IP address (feature #501 on page 57)
– Subnet mask (feature #502 on page 57)
– Default gateway (feature #503 on page 57)
– DNS server #1 (feature #504 on page 57)
– DNS server #2 (feature # 505 on page 57)
–...

10. Useful Information
60
10 Useful Information U se ful  In for m at i on
10.1 Character entry
The dial keypad is used to enter characters and 
numbers.
–Press {} to move the cursor.
– Press dial keys to enter characters and numbers.
–Press {STOP} to erase the character or number 
highlighted by the cursor. Press and hold {STOP} to 
erase all characters or numbers.
– To enter another character located on the same dial 
key, press {>} to move the cursor to the next space, 
then press the appropriate dial...