Home > Panasonic > Camera Accessories > Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

Here you can view all the pages of manual Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions. The Panasonic manuals for Camera Accessories are available online for free. You can easily download all the documents as PDF.

Page 41

Cable Compensation Unit  AW-RC400
AW-RC400
41
How to mount the AW-RC400 in a rack
Use the accessory rack-mounting adaptors and accessory
mounting screws (M4!8 mm) to mount the unit in a rack.
1Set the POWER switch at the OFF position to turn off the
power.
2Remove four feet on the bottom of the unit.
3Place the rack-mounting adaptors to the both ends of the
unit, and fix it using four mounting screws.POWER switch
Remove four feet.
Rack-mounting adaptor
Mounting
screws 

Page 42

Cable Compensation Unit  AW-RC400
42
Specifications
Input connectors
DC 12V IN: For connecting optional accessory AC adaptor (AW-PS301)
G/L IN: BNC!2, automatically terminated by 75-ohm resistance, loop-through output, black burst
VIDEO/Y, Pr/C, Pb: BNC!3 (5 sets), 75-ohm termination
Composite
Y/C
Component (Y/Pr/Pb)
MONI SEL IN: RJ45
Connecting cable: 10BASE-T straight cable (UTP category 5), max. 50 meters
Output connectors
G/L OUT: BNC!5, 75-ohm output, BELDEN 8281 connecting cable, max. 1000 meters...

Page 43

Roll Unit  AW-RL400
AW-RL400
43
Introduction
Accessories
≥The AW-RL400 roll unit enables a camera to be rotated
when it is used in combination with the AW-PH400 indoor
pan/tilt head.NOTE
≥Since the roll unit causes the camera to rotate, the user
should ensure that all the wiring such as the camera
cable and lens cable will not become entangled when
the roll unit is operated.
≥When the roll unit is to be discarded at the end of its
service life, ask a specialized contractor to dispose of it
properly in...

Page 44

Roll Unit  AW-RL400
44
Parts and their function
1Rotary ring
2Camera mounting screw (U1/4”-20UNC)
After mounting the camera, secure it firmly using this
screw.
3Camera mounting plate (A) (B)
Mount the camera on this plate using the camera
mounting screws.
4Camera mounting plate anchoring screws
After mounting the camera on the camera mounting
plate, anchor it to the roll unit using these screws.
5Roll unit anchoring screw holes
This is where the roll unit is secured to the rotary arm of
the pan/tilt...

Page 45

Roll Unit  AW-RL400
AW-RL400
45
Installation
3Loosen the two screws of camera mounting plate which is already installed to the roll unit.
Then remove the camera mounting plate. 1Attach the pan/tilt head’s rotary arm to the roll unit using the three mounting screws (M5!22 mm, with flat washers, pan/tilt
head accessory).
2Attach the rotary arm to the pan/tilt head using the mounting screws (M5!22 mm, with flat washers, pan/tilt head accessory).
Roll unit
Camera mounting plate
(consisting of 2 separate
sub...

Page 46

Roll Unit  AW-RL400
46
Installation
❈Be absolutely sure to use a screwdriver or other tool to tighten the two camera mounting screws so that the camera
mounting plate is secured firmly.
4Separate the camera mounting plate, which was removed in step 3, into its two
sub plates.
≥Separate the camera mounting plate into sub plate (A) and sub plate (B) by
loosening the clamping screw.
Clamping screw
5Follow the steps below to mount the camera mounting sub plates, which were separated in step 4, onto the...

Page 47

Roll Unit  AW-RL400
AW-RL400
47
Installation
6Attach the camera mounting plate to the roll unit in a way contrary to the procedure 
of removing it in step 3.
Camera mounting plate’s screws
7Using the pan/tilt head connecting cable provided, connect the [OPTION] connector on the pan/tilt head connector panel and
the connector on the roll unit.
OPTION connector
Pan/tilt head connecting cableLens cable
8After the roll unit, camera body and pan/tilt head have been mounted, complete the installation by...

Page 48

Roll Unit  AW-RL400
48
Specifications
Pan/tilt head connector:Connected to pan/tilt head using cable supplied
Performance:Maximum load-bearing capability: 8.8 lbs (4 kg)
Rotary range: 380 degrees (approx. ±190 degrees)
Maximum operating speed: 60 degrees/sec.
Repeatability: Less than ±1 degree
Ambient operating temperature:32°F to 113°F (0°C to +45°C)
Storage temperature:–4°F to 140°F (–20°C to +60°C)
Ambient operating humidity:30% to 90% (no condensation)
Dimensions (W!H!D):8-1/16”!7-13/16”!10-1/4”...

Page 49

49
Connections
≥Turn off the power of all the equipment before proceeding with the connections.
≥Use the AW-PS505 as the AC adaptor for the AW-RP400 pan/tilt control panel. Use the DC cable supplied with
the AW-PS505 to connect the DC 12V IN socket on the AW-RP400 with the DC 12V OUT socket on the 
AW-PS505.
≥Connect the AC power cable supplied with the AW-PH400 for the AW-PH400 indoor pan/tilt head.
≥Use the AC adaptor (optional accessory) for the AW-RC400 cable compensation unit.
≥Use 10BASE-T straight...

Page 50

50
Connections
Motorized zoom lens
Iris control
Convertible camera
Genlock signals
Video signals
Video signal output
Genlock signal input
Monitor switching signals
Monitor signals 1
Monitor for AW-CB400Monitor for AW-RP400
Monitor signals 2Camera cable supplied
with AW-PH400 Zoom/focus
control
AW-PH400
Indoor Pan/Tilt Head
Pan/tilt head/camera
control signals
AC power cable supplied
with AW-PH400
AW-RP400
Pan/tilt control panel AW-CB400
Remote Operation
Panel
Cable supplied with AW-CB400
(AW-CB400 power...
Start reading Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

Related Manuals for Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

All Panasonic manuals