Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

Pan/Tilt Control Panel  AW-RP400
AW-RP400
31
Menu settings
OPTION SWITCH A to H settings
(NOT USE / DEF / WIP / HEATER/FAN / LAMP / OPTION / ND / EXT / AF)
The following functions can be allocated to OPTION buttons A to H. Different functions can be allocated for different pan/tilt
heads.
NOT USE:The button is disabled.
DEF:This controls the ON and OFF states of the defroster function when using a pan/tilt head system
equipped with this function.
Each time the button is pressed, ON is switched to OFF or...

Pan/Tilt Control Panel  AW-RP400
32
Menu settings
CONTROL SELECT MODE setting (INTERLOCK/UN-INTERLOCK)
This menu item is for selecting the method used to select the pan/tilt head and camera when the AW-CB400 remote
operation panel has been connected to the AW-RP400 control panel.
INTERLOCK:When the pan/tilt head and camera system are selected by the AW-RP400 or AW-CB400, the same
system is selected by the other unit as well.
UN-INTERLOCK:A different pan/tilt head and camera system can be selected by the...

Pan/Tilt Control Panel  AW-RP400
AW-RP400
33
How to mount the AW-RP400 in a rack
AW-RP400
320mm
1Use the accessory mounting screws (M4!8 mm) to attach the rack-mounting adaptors.
Rack-mounting adaptor
Accessory mounting
screws (M4!8 mm)
4 pcs
≥The AW-RP400 is 320 mm wide. If it is to be installed in a full-size rack (which accommodates units totaling
420 mm in width), provide panels or other parts to supplement the AW-RP400’s width so that it will fill the
rack width-wise.
≥If the AW-RP400 is joined to...

Pan/Tilt Control Panel  AW-RP400
34
How to change the position of the connector panel
The position of the connector panel can be changed from the rear panel to the bottom panel.
1Remove the five bottom panel screws, and remove the
blank panel.
2Remove the five rear panel screws, and remove the
connector panel.
5Secure the connector panel to the bottom panel using the
screws. 3Secure the blank panel to the rear panel using the
screws.
4Remove the two rubber feet from the blank panel.
Screws!5 (bottom...

Pan/Tilt Control Panel  AW-RP400
AW-RP400
35
How to replace the zoom switch
1Remove the four screws that secure the zoom lever.
2Pull out the zoom lever, disconnect the two cables from
the circuit board inside, and remove the zoom lever.
3Plug the two cables extending from the zoom switch into
the connectors on the circuit board inside.
4Secure the zoom switch using the four screws.
Screws!4
Screws!4
❈Before replacing the zoom switch, turn off the power. 

Pan/Tilt Control Panel  AW-RP400
36
Replacing the consumable parts
The joysticks and zoom switch are consumables.
Replace them if they are not working properly.
Ask your dealer to do the replacement work. 

Pan/Tilt Control Panel  AW-RP400
AW-RP400
37
Specifications
Input connectors
DC 12V IN: XLR, 4 pins
CONTROL IN FROM ROP: D-SUB 29-pin, cable supplied with AW-CB400 remote operation panel
CONTROL IN FROM RCB: 10-pin round connector, cable supplied with WV-CB700A
EXT CONT IN: RJ45, additional AW-RP400 control signal input; 10BASE-T straight cable (UTP category 5),
max. 500 meters
REMOTE: 50-pin D-SUB connector, external control input, AW-CA50T9
Output connectors
CONTROL OUT TO 
PAN/TILT HEAD: RJ45,...

Cable Compensation Unit  AW-RC400
38
Introduction
Accessories
≥The AW-RC400 is capable of providing cable
compensation for analog composite, analog Y/C or analog
component signals in five channels up to 500 meters
(when the BELDEN 8281 connecting cable or its
equivalent is used).
≥It features a 5µs advance function for the sync signals in
order to provide easy support for a system (another cable
compensation unit is required) in which the coaxial cable
connected between this AW-RC400 cable compensation...

Cable Compensation Unit  AW-RC400
AW-RC400
39
Parts and their function
1Power LED
This lights up green when the (2) POWER switch is set
to ON while a DC 12V voltage is supplied to the (7) DC
12V IN socket.
2POWER switch
Set this to ON to turn on the cable compensation unit’s
power. Part of the power supply circuitry will still operate
even when the power switch is at the OFF position. To
turn off the power completely, disconnect the AC adaptor.
3Cable length setting switches [0 to 5]
Set these switches...

Cable Compensation Unit  AW-RC400
40
Parts and their function
;MONITOR1, 2 connectors
The video signals of the cameras selected by the 
AW-RP400 pan/tilt control panel or the AW-CB400
remote operation panel which is connected to the 
AW-RP400 are output from these connectors.
The output signals are cable-compensated signals of the
same type as the input signals. For instance, if a channel
to which composite signals have been input is selected,
these composite signals will be cable-compensated and...