Panasonic Indoor Pan Tilt Head Aw Rp400 Operating Instructions

Indoor Pan/Tilt Head  AW-PH400
AW-PH400
11
Parts and their function
JY connector [Y]
This is the output connector for the camera’s video
signals.
It is connected to the Y/VIDEO connector on the 
AW-RC400 cable compensation unit or monitor, etc.
Use a BNC coaxial cable for the connecting cable.
The AW-PB302 RGB card must be installed if the 
AW-E300, AW-E300A, AW-E600, AW-E800 or 
AW-E800A convertible camera is to be used.
K1394 connector [1394]
This is used for the control of the convertible camera and...

Indoor Pan/Tilt Head  AW-PH400
12
Installation(Be sure to ask your dealer to install the unit.)
For a stand-alone installation
For installation on the ceiling
$Assembling the pan/tilt head
When assembling the pan/tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws
firmly. After mounting the pan/tilt head, check there is no play in its installation.
1Attaching the camera mounting base
Attach the camera mounting base to the rotary arm using the three...

Indoor Pan/Tilt Head  AW-PH400
AW-PH400
13
Installation(Be sure to ask your dealer to install the unit.)
3Mounting the tally lamp
Connect the cable connector which is taped to the top of the pan/tilt head to the tally lamp connector.
Mount the tally lamp on the top of the pan/tilt head using the two screws provided.
Mount the lamp while paying attention to the wire.
If the tally lamp is not going to be used, insert the cable which is stuck to the top of the pan/tilt head inside the pan/tilt head,
and...

Indoor Pan/Tilt Head  AW-PH400
14
Installation(Be sure to ask your dealer to install the unit.)
$Setting the mounting direction switch
Set the switch as follows when the unit is to be installed on the ceiling.
(This switch was set to the stand-alone installation position at the factory.)
1Remove the four screws, and gently remove the pedestal connector panel.
2Set switch S1 on the PCB inside the pan/tilt head as follows.
For stand-alone installation:
Set S1 to the rear position (T). (Factory setting)
For...

Indoor Pan/Tilt Head  AW-PH400
AW-PH400
15
Installation(Be sure to ask your dealer to install the unit.)
$Setting the PCB switches
The switches on the CONNECTOR PCB will need to be set in accordance with the signals to be transmitted and the equipment
to be connected to the pan/tilt head.
(The switches are set to support analog/SDI at the factory.)
≥Analog/SDI support
IP/IEEE switch: IEEE
422/IP switch: 422
≥Web card support
IP/IEEE switch: IP
422/IP switch: IP
≥IEEE1394 card support
IP/IEEE switch:...

Indoor Pan/Tilt Head  AW-PH400
16
Installation(Be sure to ask your dealer to install the unit.)
$Installing the pan/tilt head
When installing the pan/tilt head, follow the instructions below carefully.
In order to prevent accidents resulting when the product becomes dislodged or falls down, be absolutely sure to proceed as
instructed. Do not install the pan/tilt head on its side since its prescribed operation and performance cannot be ensured.
≥After the pan/tilt head has been installed, mount the camera...

Indoor Pan/Tilt Head  AW-PH400
AW-PH400
17 $Mounting the camera
When mounting the camera on the pan/tilt head, be very careful to ensure that the camera does not fall off or fall down.
1Mount the lens onto the convertible camera. (Before mounting a large lens, consult with your dealer.)
2Insert the rubber piece between the camera and pan/tilt head, and mount the convertible camera after aligning it with the
guide pins. Use a tool to tighten up the mounting screws so that they are securely tightened.
❈Be...

Indoor Pan/Tilt Head  AW-PH400
18
Installation(Be sure to ask your dealer to install the unit.)
$Attaching the wire
The wire is not provided. Use one which is strong enough to bear the weight of the whole camera (camera + lens).
When mounting the cameras with fan (AW-E655, AW-E750, AW-E800, AW-E800A)
1Use the wire mounting screw (M4!8 mm with flat washer and spring washer) to attach one end of the wire to the pan/tilt
head’s arm.
2Mount the mounting spacer on the top panel of the camera.
3Use the wire...

Indoor Pan/Tilt Head  AW-PH400
AW-PH400
19
Replacing the consumable parts
$Replacing the battery
The battery has a service life of approximately 5 years.
The unit stores the preset positions, limiters and other data in its memory. This data is retained even when the power is turned
off, but if the internal battery has reached the end of its service life, the data will be lost when the power is turned off.
Replace a battery that has lost its charge with a new one. (Battery used: CR2032 manganese...

Indoor Pan/Tilt Head  AW-PH400
20
Specifications
Genlock input:BNC
Black burst or composite video signal
Prompter input
(PROMPTER IN):BNC
Through output to PROMPTER connector
Prompter output
(PROMPTER OUT):D-SUB 15-pin
Camera video output
VIDEO: BNC, 75-ohm output
Y: BNC, 75-ohm output
Pr/C: BNC, 75-ohm output
Pb: BNC, 75-ohm output
SDI: BNC
Camera, pan/tilt head control:RJ45, RS-485, pan/tilt head control signal output
RP/IP Connecting cable: 10BASE-T straight cable (equivalent to UTP category 5), 
max....