Panasonic Hx Wa10 Owners Manual

							VQT3P35171
IMPORTANT MESSAGES AND ALERTS
Viewing images Why is the image 
too bright?
The subject was 
too bright.When capturing an 
image, devise a way 
to compensate for a 
bright subject, for 
example, by 
changing the 
shooting angle.
Why is the image 
out of focus? The focus is not 
locked properly.Hold the camera 
correctly and slowly 
press the [
O] 
button halfway to 
lock the focus. Then 
press the [ O] 
button all the way to 
capture the image.
Why is there no 
image? This may happen 
when trying to 
play back images 
stored on a card 
from a different 
digital camera.Play back images 
that were recorded 
on a card using this 
camera.
Why is the 
playback image 
distorted? If the subject 
moves or the 
camera is moved 
during recording, 
a distorted image 
may sometimes 
occur.Not a malfunction. 
This is a 
characteristic of the 
MOS sensor.
Question
Answer Action 
						

							172VQT3P35
IMPORTANT MESSAGES AND ALERTS
Viewing images Why isn’t the 
magnified image 
clear?
Due to the 
characteristics of 
the camera, 
magnified images 
appear less clear.Not a malfunction.
Why isn’t the 
captured image 
clear? The image was 
captured using 
the digital zoom.Not a malfunction.
Can I play back 
image and sound 
files that I edited 
using my 
computer? — Please note 
playback of files that 
were processed 
using software other 
than HD Writer VE 
1.0 cannot be 
guaranteed.
Why is there a 
motor-like sound 
during video 
playback? The sound of the 
camera’s 
mechanical action 
was recorded (the 
sound of the 
optical zoom 
movement or the 
autofocus sound).Not a malfunction.
Round white 
spots that look like 
bubbles are 
appear in photos. When the flash is 
used indoors or in 
dark 
surroundings, 
dust in the air may 
reflect the light 
from the flash and 
appear as round 
white dots.Not a malfunction. It 
is characteristic that 
the position and 
number of round 
spots changes with 
each shot.
Connecting 
to a TVWhy is there no 
sound? The volume on 
the TV is set to 
the minimum.Adjust the volume 
on the TV.
Question
Answer Action 
						

							VQT3P35173
IMPORTANT MESSAGES AND ALERTS
Misc.The “Cannot edit, 
differing settings 
exist.” message 
appears.
You have 
attempted to 
splice videos that 
were recorded in 
different recording 
modes.Select videos that 
were recorded in the 
same recording 
mode.
Why is a noise 
heard from a 
nearby TV or 
radio during 
battery 
recharging? Electromagnetic 
waves are emitted 
from the AC 
adaptor.
Move the AC 
adaptor further away 
from the TV or radio 
when recharging the 
battery pack.
Why does the 
“CARD FULL.” or 
“Built-in Memory 
full.” message 
appear? There is no more 
available memory 
on the card or in 
the camera’s built-
in memory.Delete unnecessary 
files, or use a card 
that has more 
memor y available.
Why does the 
“Card is 
protected” 
message appear? The lock switch on 
the card is in the 
locked (protect) 
position.Move the lock switch 
to the unlocked 
position.
Why can’t the 
camera be 
operated? A temporary 
internal circuitry 
problem may be 
the cause.Remove the AC 
adaptor and the 
battery pack from 
the camera, wait a 
few minutes, then 
reinstall the battery 
pack and try again.
A problem such 
as inability to 
record or play 
back occurs. The card contains 
files that were 
saved using a 
device other than 
this camera.After saving your 
files to a different 
medium, format the 
card.
Some parts of the 
unit, such as the 
battery cover or 
terminal cover, 
cannot be moved. The affected part 
is frozen. Or, a 
foreign substance 
such as dust or 
sand has gotten 
inside.Movement will be 
restored when the 
unit is returned to a 
normal temperature. 
Or, use the supplied 
brush to remove the 
foreign substance, 
or rinse with fresh 
water.
Question
Answer Action 
						

							174VQT3P35
IMPORTANT MESSAGES AND ALERTS
Misc.Can I use my 
camera abroad?
— You can charge the 
battery and connect 
to a TV to view your 
recordings when 
abroad.
Why does the 
“ERROR 
OCCURRED. 
PLEASE TURN 
UNIT OFF, THEN 
TURN ON 
AGAIN.” message 
appear? A problem has 
occurred within 
the camera or 
card.
Check the following 
items:
1
Remove the 
card and then 
install it again.
2 Remove the 
battery pack and 
then install it 
again.
3 Install a different 
card.
If “ERROR 
OCCURRED. 
PLEASE TURN 
UNIT OFF, THEN 
TURN ON AGAIN.” 
still appears after 
performing the 
above steps, then 
take the camera to 
the dealer for 
service.
Question
Answer Action 
						

							VQT3P35175
IMPORTANT MESSAGES AND ALERTS
TROUBLESHOOTING
Before taking your camera to the repair shop, check the following table for a 
possible solution to the problem.
Camera
Problem Cause ActionReference page
Power No power. The battery 
pack is dead.Recharge the 
battery pack, or 
replace with a 
fully charged 
battery pack. 
Or connect the 
AC adaptor.
33
The battery 
pack has not 
been inserted 
correctly. Insert the 
battery pack 
correctly.
A blinking 
temperature 
warning icon is   shown, 
and the 
camera does 
not turn on. The battery 
pack is too hot.
Wait for the 
battery pack to 
cool down.
39
The camera 
turns off by 
itself. The camera 
has switched 
to the sleep 
mode.Turn on the 
camera again.
43 
						

							176VQT3P35
IMPORTANT MESSAGES AND ALERTS
ShootingAn image is 
not captured 
when the [
O] 
button or [ @] 
button is 
pressed. The power is 
not turned on.
If the camera 
has switched to 
the sleep 
mode, turn on 
the camera 
before 
shooting.
If the camera 
was turned off, 
press the 
power button to 
turn it on. 42, 43
The maximum 
number of 
images that 
can be 
captured or the 
maximum 
video 
recording time 
has been 
reached. Install a new 
card.
40
Delete the 
images that are 
not necessary. 75
The flash does 
not operate. The flash 
mode is set to 
. Set the flash 
mode to k
 or 
m . 51
The battery 
pack is dead. Recharge the 
battery pack, or 
replace with a 
fully charged 
battery pack. 
Or connect the 
AC adaptor 
(optional). 33
Problem Cause Action
Reference 
page 
						

							VQT3P35177
IMPORTANT MESSAGES AND ALERTS
ShootingThe digital 
zoom does not 
work.
The digital 
zoom setting is 
set to  .Set the digital 
zoom setting to 
. 55, 67
There is noise 
in the captured 
image. The ISO 
sensitivity 
setting is too 
high.Set the ISO 
sensitivity to a 
lower setting.
53, 88
The  icon 
appears, and 
shooting is not 
possible. The camera’s 
internal 
temperature is 
high.Discontinue 
shooting, and 
wait for the 
camera to cool 
down before 
using it again.
39
Problem Cause Action
Reference 
page 
						

							178VQT3P35
IMPORTANT MESSAGES AND ALERTS
LCD 
monitor No playback 
image 
appears. The camera is 
not set to the 
playback 
mode.Set the camera 
to the playback 
mode.
47
Viewing  images The image is 
too dark.
The flash was 
blocked by a 
finger or other 
object.Hold the 
camera 
correctly, and 
make sure the 
flash is not 
obstructed.
61
The subject 
was too far 
away. Capture the 
image in the 
range of 
operation of the 
flash.
196
The subject 
was lit from 
behind. Set the flash 
mode to m
.51
Use the 
exposure 
compensation 
function. 97
Use the spot 
Y  light-
measuring 
mode. 53
There is not 
enough light. Adjust the ISO 
sensitivity 
setting.
53, 88
Problem Cause Action
Reference 
page 
						

							VQT3P35179
IMPORTANT MESSAGES AND ALERTS
Viewing images
The image is 
too bright. The flash 
mode is set to 
m.Select a flash 
mode other 
than m.51
The subject 
was too bright.
Use the 
exposure 
compensation 
function.
97
The ISO 
sensitivity 
setting is 
incorrect.Set the ISO 
sensitivity to 
=.53, 88
The image is 
not in focus.
The subject is 
too close to the 
camera.Capture the 
image with the 
subject within 
the appropriate 
distance/range.
Select the 
correct focus 
setting for your 
needs.
53, 87The focus 
setting is not 
correct.
The camera 
moved when 
the [
O] 
button was 
pressed. 
(camera 
shake) Hold the 
camera 
correctly and 
slowly press 
the [
O] 
button halfway 
to lock the 
focus. Then 
press the [
O] 
button all the 
way to capture 
the image.
61, 64
The focus is 
not locked 
properly.
The lens is 
dirty. Clean the lens.
—
Problem Cause Action
Reference 
page 
						

							180VQT3P35
IMPORTANT MESSAGES AND ALERTS
Viewing images The colors of 
the images 
captured 
indoors are not 
correct.
This is due to 
ambient 
lighting.
Set the flash 
mode to  . 51
The white 
balance setting 
is incorrect. Set the white 
balance setting 
correctly.
53, 89
A part of the 
image is 
missing. The handstrap 
or a finger was 
blocking the 
lens.Hold the 
camera 
correctly, and 
make sure the 
lens is not 
obstructed.
61
“No image” is 
shown. There is no file 
in the built-in 
memory or in 
the installed 
card.Play back after 
capturing 
images or 
making audio 
recordings.
—
During audio 
playback, there 
is no sound. The play 
volume setting 
on the camera 
is too low.Adjust the play 
volume.
56, 72, 
82, 163
Connecting  to a TV
There is no 
color in the 
image.
The image is 
distorted. The TV output 
setting is not 
correct.
Select the 
correct TV 
output setting. 119, 122
Problem Cause Action
Reference 
page