Panasonic Hx Wa10 Owners Manual

							VQT3P35121
OPTION SETTINGS
1REC FOLDER setting 
(page 126) 
(when the recording mode is 
active)
h Select a folder to record to.
2 PLAYBACK FOLDER setting  
(page 127)
(when the playback mode is 
active)
h Select a folder to play back.
3 FILE NO. CONT’D setting 
(page 128)
4 Remaining battery charge 
display (page 133) 
						

							122VQT3P35
OPTION SETTINGS
TV output setting (page 119)
Specify the type of image signal that is output from your camera’s USB/AV 
terminal.
1 Select [TV OUTPUT], and press 
the SET button.
TV SYSTEM:
Set the type of TV signal that is 
output from the USB/AV terminal.
TV ASPECT:
Set the TV’s aspect ratio.
HDMI:
Set the signal that is output from 
the HDMI terminal.
VIERA Link:
Set the VIERA Link function.
2 Select the desired setting, and press the SET button.
h The screen to change the parameter for the selected setting appears.
 NTSC: Outputs NTSC video signals.
PA L : Outputs PAL video signals.
 16:9: Use this setting when a TV having an aspect ratio of 16:9 is 
connected.
4:3: Use this setting when a TV having an aspect ratio of 4:3 is 
connected.
 AU TO: The camera automatically determines the appropriate setting.
720p: Choose this setting if the video was recorded in the   or 
 mode.
1080i:   Choose this setting if the video was recorded in the   or 
 mode.
480p: Choose this setting if the video was recorded in the   
mode.
h Does not work with 480i connector.
SET
NTSC
16:9
TV OUTPUT
TV SYSTEM
TV ASPECT
HDMI
VIERA Link ENTERAUTO
ON 
						

							VQT3P35123
OPTION SETTINGS
ON: Use the VIERA Link.
OFF: Do not use the VIERA Link.
3 Press [I] or [J ] to select the desired parameter.
4 Press the SET button.
5 Press the MENU button 2 times.
hThis completes the TV output setting. 
						

							124VQT3P35
OPTION SETTINGS
Relation between [TV ASPECT] setting and TV 
display
The tables below show the video signal that is output when the [TV ASPECT] 
setting is changed. However, note that for some TVs that have an auto-detect 
function, the output may not conform to the table, or the TV display may not 
change at all.
[TV 
ASPECT]  settingTV type to be connectedImage file to be  displayedTV display
4:3 4:3 Photo
(4:3)
Video in SD mode
Video in HD mode 
						

							VQT3P35125
OPTION SETTINGS
HINT
If the TV display is not correct…i If the appearance of the image on the TV monitor is not correct, you can 
either change the camera’s [TV ASPECT] setting, or change the screen 
size setting on your TV. To change the screen size setting on your TV, 
please refer to the instruction manual for your TV.
The aspect ratio of the output photo does not change to 16:9? i The photo output will be 4:3 for images captured in the 4:3 photo mode.16:9 16:9
Photo
(4:3)
Video in SD mode
Video in HD mode
[TV 
ASPECT]  settingTV type to be 
connectedImage file to be  displayedTV display 
						

							126VQT3P35
OPTION SETTINGS
Storage folder setting (page 121)
Create or select a recording folder (a folder in which to store recorded files).
1 Set the camera to the recording mode, and display the Option 
Setting Menu.
2 Select [REC FOLDER], and 
press the SET button.

hSelect [CREATE NEW 
FOLDER].

h Select the desired folder 
number.
3 Press the SET button.
hThis completes the create/select folder setting.
h If you created a new folder, it automatically becomes the selected 
recording folder.
HINT
When an existing folder cannot be selected or a new one created...
i A folder cannot be selected if it was created using a different device, or if it 
already contains the maximum number of files.
SET
100CDPFP
REC FOLDER
CREATE NEW FOLDER
ENTER 
						

							VQT3P35127
OPTION SETTINGS
Playback folder setting (page 121)
If the card contains multiple folders, you can select from which folder you 
would like to play back.
1 Set the camera to the playback mode, and display the Option Setting 
Menu.
2 Select [PLAYBACK FOLDER] and 
press the SET button.
3 Press [I] or [ J] to select the desired playback folder, and press the 
SET button.
h The files in the selected folder are displayed in the Playback Screen.
100CDPFP
101CDPFP
102CDPFP
PLAYBACK FOLDER
ENTER 
						

							128VQT3P35
OPTION SETTINGS
File No. continued setting (page 121)

If a newly formatted card is used, the file name (image number) of the 
captured image automatically begins from 0001. If the card is subsequently 
reformatted, or if a different reformatted card is used, the file names again 
begin from 0001. 

By setting the file number continued function to [ON], even if the card is 
reformatted or the card is replaced with another card, the consecutive 
numbering of file names continues from the last number recorded by the 
camera.File name (image number)
Card A 0001, 0002 ...... 0012, 0013
Card B 0001, 0002 ...... 0012, 0013
File name (image number)
Card A 0001, 0002 ...... 0012, 0013
Card B 0014, 0015 ....... 0025, 0026
Replace card
Replace card 
						

							VQT3P35129
OPTION SETTINGS
iIf Card B already has files in it when it replaces Card A, file names are 
assigned as follows.
When the highest file number on Card B (before replacing) is lower 
than the highest file number on Card A:  the file name of the next 
recorded image continues from last file name recorded on Card A.
When the highest file number on Card B (before replacing) is higher 
than the highest file number on Card A:  the file name of the next 
recorded image continues from last file name recorded on Card B.
HINT
When the built-in memory is used... i If the file number continued function is [ON], file name numbering 
continues just the same as when an SD card is used, even if the built-in 
memory is formatted or the medium is switched to the SD card.
At the end of a photography session...
i Until the file number continued functi on is set to [OFF], consecutive file 
names are assigned. Card A 0001, 0002 ..... 0012, 0013
Card B 0001, 0002, 0014, 0015 ..... 0025, 0026
Previously recorded files
Replace card
Card A 0001, 0002 ..... 0012, 0013
Card B 0020, 0021, 0022, 0023 ..... 0025, 0026Previously recorded files
Replace card 
						

							130VQT3P35
OPTION SETTINGS
Formatting (initializing) (page 119)
A card must be formatted with this camera:i After purchasing, when used for the first time, or
i If it was formatted using a personal computer or other device.
The card cannot be formatted if the lock switch is set to the “LOCK” position. 
Proceed with the format procedure after setting the lock switch to the 
unlocked position (page 29).
HINT
Caution during formatting i Do not turn off the power to the camera or eject the card during formatting.
Formatting the card erases the files
i When a storage medium is formatted, all recorded files on the medium are 
erased. Protected data (page 99) is al so erased, so before formatting a 
card, any data you want to keep should be copied to your personal 
computer’s hard disk or other storage medium.
When disposing of or transferring the SD card, execute the [DELETE 
DATA] procedure from the Format Menu
i If a card is reformatted or the data is erased from the card using the 
camera or a computer, the card’s control data may be merely modified and 
the data itself may not be completely erased from the card.
i In some cases it may be possible to recover the data from a reformatted 
card using special software for that purpose. However, if the camera is 
used to erase data, it will be impossible  to recover the data even by the use 
of data recovery software.
i If you are disposing of a card, it  is recommended that you physically 
destroy it. If you are transferring the card to someone else to use, it is 
recommended that you use the camera to erase the data, or use 
commercially available software for erasing card data. Managing data is 
the responsibility of the user.
Can’t select [DELETE DATA]? i Use the AC adaptor to power the camera. [DELETE DATA] cannot be 
selected when the battery is used to power the camera.