Panasonic Hdtv Projection Monitor Pt 4743 Operating Instructions

							PICTURE IN PICTURE AND SPLIT OPERATION9 lENGLISHPIP Operation (cont.)
•Press  to display search frames.
•Press  again to stop search feature. PIP or
Split frame channel will be the last active search frame.
•Press  or  to cancel PIP or Split frame 
Move Button (PIP only) 
This feature is used to move PIP frame to one of four
corners.
Procedure
•Press  to display PIP frame.
•Press  to position PIP frame to desired corner.
•Press  to cancel PIP frame. 
PIP MIN and PIP MAX Buttons
While PIP frame is displayed, press PIP MIN or PIP MAX
button to vary the size of PIP frame.
Procedure
•Press  to display PIP frame.
•Press  or  to size PIP frame.
•Press  to cancel PIP frame.
Freeze Button (PIP and Split) 
This feature is used to stop action in PIP or Split frame.
Procedure
•Press  or  to display PIP or Split frame•Press  to stop PIP or Split frame action. 
•Press  again to continue action. 
•Press  or  to cancel PIP frame.      
Main Picture Freeze Feature
This feature is used to stop action of the Main Picture and
display it on a Split or PIP freeze frame.
Procedure
•To stop action for Main picture, press  while
PIP or Split frame is not displayed.
•Main Picture freeze will be displayed in a PIP or Split
frame, depending on the selection in the Freeze menu
located in Picture Other ADJ. section (refer to page 21).
•Press  again to cancel Main Picture freeze
frame.
Note:While Main Picture freeze frame is displayed, only
MOVE button is active for PIP, all other PIP and Split
buttons have no effect  (see chart ).
PIP, Split and Freeze Mode Buttons Operational chart
This chart indicates the buttons that are operational with 
PIP, Split or Main Picture Freeze mode.       SEARCHOPEN/CLOSE
pSEARCH
OPEN/CLOSE
pPIPSPLIT2
3
4Search Frames Main PicturePIP MOVEPIPPIP FrameMain PicturePIP PIP MIN PIP MAXPIPMain PictureMAX
MINPIPSPLITREMOTE 
BUTTONSPIP MODESPLIT MODEMAIN 
PICTURE
FREEZE 
MODEPIP MINSize SmallerNo EffectNo EffectPIP MAXSize LargerNo EffectNo EffectFREEZEFreeze PIP 
frameFreeze Split 
FrameDisplay or 
DeletePIP CHChange 
ChannelChange 
ChannnelNo EffectSEARCHDisplays 
Search FrameDisplays 
Search frameNo EffectPIPDisplays PIP 
FrameDisplays PIP 
frameNo EffectSPLITDisplays Split 
FrameDisplays Split 
frameNo EffectMOVEMove PIP 
FrameNo EffectMove PIP 
FrameSWAPSwap with Main 
PictureSwap with 
Main PictureNo EffectFREEZETV/VCRFREEZETV/VCRPIPSPLITMain PictureMain Picture
PIP freeze frame
Note:Audio is from Main Picture only.Split freeze frameFREEZE
TV/VCRFREEZE
TV/VCRnew2prod 0470-1 E doc2.fm  Page 9  Friday, May 2, 2003  12:31 PM 
						

							10 lREMOTE CONTROL OPERATION (MODELS PT-47WXC43 AND PT-47WX33)ENGLISHRemote Control Operation (models PT-47WXC43 and PT-47WX33)                Press to turn ON and OFF.POWERMUTE
 Press to mute sound. Press to display and
cancel CC (Closed Caption).SAP
 Press to access audio modes (Stereo, SAP or 
Mono)TV/VIDEO
 Press to select TV or input modes.Press to select remote operation.
  TV VCRDBS/CBL DVDACTIONPress to access menus.Press to select next or previous channel and 
navigate in menus.CH
CHPress to adjust TV sound and navigate in 
menus.VOL  VOLSEARCH
GUIDESEARCH - Press for PIP or SPLIT search.
GUIDE - DBS functions buttonEXITDBS functions button.*PIP MIN
REW*SPLIT
 PLAY*PIP MAX
FF*SWAP
PAUSE*MOVE
STOP*PIP
REC*FREEZE
TV/VCR *PIP CH
VCR /DBS CH*Split and PIP function buttons
Component function buttons
uPress numeric keypad to select any channel.7412580963R-TUNEPress to switch to previously viewed 
channel or input modes.Battery Installation
Use two AA batteries:
Remove battery cover by pushing in and up neararrow.
Install batteries matching (+) and (-) polarity signs.
Replace the battery cover.
Note:Incorrect installation can cause battery leakage and
corrosion that will damage the Remote ControlPrecautions
•Replace batteries in pairs.
•Do not mix battery types (zinc carbon
with alkaline).
•Do not recharge, heat, short-circuit,
disassemble, or burn batteries.ASPECT
PROGASPECT - Select picture size (ratio) to match 
programming format.
PROG - Press to enter minor number in a 
compound number.RECALLPress to display time, channel, sleep timer, 
and other options.BBE
MENU
 BBE - Press to turn on or off.
MENU- Press to access DBS or DVD menus.EUR7613Z40new2prod 0470-1 E doc2.fm  Page 10  Friday, May 2, 2003  12:31 PM 
						

							REMOTE CONTROL OPERATION (MODELS PT-47WXC43 AND PT-47WX33)11 lENGLISHOperating Components with Remote Control
Note:Refer to page 12 for programming Remote Control
procedure.
Operating a VCR
Program the remote control to use with VCR.
Operating a CABLE BOX
Program the remote control to use with Cable Box. Operating a DBS
Program the remote control to use with DBS.
Operating a DVD
Program the remote control to use with DVD
 TO DO THIS...PRESSTurn on/offSelect TV Input mode for VCRChange Channels up/downVCR/DBS CHRecordRECPlayPLAYStopSTOPFast ForwardFF Rewind the TapeREWPausePAUSEChange to TV or VCR ModeTV/VCR On screen VCR Display RECALLTO DO THIS...PRESSTurn on/offSelect a ChannelChange Channels Up/DownBack to previous channelR-TUNEPOWERTV/VIDEO
uPOWER7412580963CH
CHTO DO THIS...PRESSTurn on/offDisplay DBS menuACTIONMenu NavigationSelect a ChannelProgram InformationRECALLBack to previous channelR-TUNESelect next page up/downVCR/DBS CHExit menusDisplay program GuideGUIDETO DO THIS...PRESSTurn on/offNext/Previous ChapterDVD DisplayRECALLSkip Search ReverseREWSkip Search Fast ForwardFF PlayPLAYDVD Open/CloseTV/VCRStopSTOPStillPAUSESlow +/-VCR CHANNEL POWERVOL  VOLCH
CH7412580963EXITPOWERCH
CH
unew2prod 0470-1 E doc2.fm  Page 11  Friday, May 2, 2003  12:31 PM 
						

							12 lREMOTE CONTROL OPERATION (MODELS PT-47WXC43 AND PT-47WX33)ENGLISHProgramming The Remote
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, CABLE or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
Note:Determine the manufacturer of the component and look
in the table for the code.
Procedure
•Confirm that the external component is plugged and
operating.
•Turn the component off.
•Press  and  together, for at least 5
seconds.
•Press appropriate component button on the Remote
Control VCR, DVD, CABLE or DBS.
•Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons).
•Press the Remote Control  to test the
component. If the procedure was successful, the
component will turnon. 
Note:If the component does not operate with the Remote
Control, repeat the procedure using another code.
(Some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming Without A Code
This procedure searches all codes and is called the
“sequence method.”
•Confirm that the external component is plugged in
and on.
•Turn the component off.
•Press  and  together, for at least 5
seconds.
•Press appropriate component button on the
Remote Control.
•Press VOL uto move forward to the next code.
Press t VOL to move backward.
•Press the Remote Control  to test the
component. If the procedure was successful, the
component will turn on.
Note:Repeat the above steps until the component code is
found. It may take many attempts before the correct
code isfound.
•After the code is found, press  to store the
code.Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.DeviceOperatesDefaultTVTV (Panasonic Only)Panasonic CodeDBS/CBLDBS STB & CBL STB (Preset)Panasonic DBS CodeVCRVCR (Preset)Panasonic Code DVDDVD (Preset) Panasonic CodeACTIONPOWERPOWERACTIONPOWERPOWER
ACTIONWrite the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.     VCR CABLE DVD   DBS  new2prod 0470-1 E doc2.fm  Page 12  Friday, May 2, 2003  12:31 PM 
						

							REMOTE CONTROL OPERATION (MODELS PT-47WXC43 AND PT-47WX33)13 lENGLISHComponent Codes (cont.)Codes For VCR   BrandCodeAdmiral335Aiwa332Akai314, 315, 316, 329Audio 
Dynamic311, 339Bell & Howell305, 313Broksonic320, 326Canon323, 325CCE343Citizen306Craig305, 306, 329Curtis 
Mathes324, 345Daewoo 301, 324, 343DBX310, 311, 339Dimensia345Emerson303, 319, 320, 325, 
326, 343Fisher305, 307, 308, 309, 
313Funai320, 326, 334GE324, 333, 345Goldstar306Gradiente334Hitachi300, 323, 345Instant 
Replay323, 324Jensen339JVC310, 311, 334,339Kenwood306, 310, 311, 339LXI300, 305, 306,307, 
308, 309Magnavox323, 324, 331Marantz310, 311, 339Marta306Memorex309, 324MGA338, 340, 341, 
347,348Minolta300, 345Mitsubishi338, 340, 341, 347, 
348Multitech304, 347NEC310,311, 334, 339Olympic323, 324Optimus306, 321, 328, 335Orion320, 326Panasonic321,322, 323, 324Penney300,305, 310, 311, 
324, 339, 345 Pentax300,311, 345Codes For VCR (Contd.)BrandCodePhilco320, 323, 324, 326, 
331, 343Philips323, 324, 331Pioneer323Proscan300, 301, 302, 323, 
324, 331, 333, 345, 
346Quasar321, 322, 323, 324Radio Shack305, 309, 324, 333, 
336, 340RCA300, 301,302, 323, 
324, 331, 333, 345, 
346Realistic305, 309, 324, 336, 
340Samsung302, 304, 333Sansui320, 326, 339, 352Sanyo305, 309, 313Scott301, 302, 304, 309, 
320, 326, 338, 340, 
347, 348Sears300, 305, 306, 307, 
308Sharp335, 336Shintom317Signature 
2000335Singer337Sony328, 329, 330Sylvania331, 324, 331Tashiro306Tatung310, 311, 339Teac310, 311, 339Technics321, 322, 323, 324Teknika324Toshiba301, 346Vector 
Research311Wards306, 309, 335, 336, 
344Yamaha305, 310, 311, 339Zenith306,344  Codes For Cable BoxBrandCodeABC224Archer225, 232Cableview205, 232Citizen205, 222Curtis212, 213Diamond224, 225, 
232Eagle229Eastern234GCbrand205, 232Gemini222General
Instrument/
Jerrold211, 219, 
220, 221, 
222, 224, 
225, 226, 
227Hamlin212, 218, 
240, 241, 
242, 245Hitachi203, 224Macom203, 204, 
205Magnavox233Memorex230Movietime205, 232Oak202, 237, 
239Panasonic209, 210, 
214Philips206, 207, 
228, 229, 
230Pioneer201, 216Pulsar205, 232Puser232RCA215Realistic232Regal212, 218, 
240, 241, 
242, 245, 
249Regency234Rembrandt205, 232, 
237Samsung205Scientific Atlanta211, 212, 
213Slmark201, 205Sprucer205, 210Stargate205, 210Teleview201, 205Texscan244Tocom235Toshiba204Unika225, 232Codes For Cable Box (Contd.)BrandCodeUniversal222, 232Videoway206Viewstar229, 230Zenith200, 217Zenith/.Drake 
Satellite200Codes For DBS  BrandCodeDish Network 
(Echostar)105, 115, 116Echostar105Express VU105, 115G. E.106G.I. (General 
Instrument)108Gradiente114Hitachi103, 111, 
112HNS (Hughes)103Magnavox101, 102Panasonic104Philips101, 102Primestar108Proscan106, 109, 
110, 113RCA106, 109, 
110, 113Sony107Star Choice103, 108Toshiba100Uniden101, 102Codes For DVDBrandCodeDenon100Ferguson101JVC109Mitsubishi105Nordmende101Panasonic100Philips103Pioneer102RCA101Saba101Samsung110Sharp108Sony104Technics100Thomson101Toshiba103Yamaha100Zenith107new2prod 0470-1 E doc2.fm  Page 13  Friday, May 2, 2003  12:31 PM 
						

							14 l
RE M OTE CO NTR O L OP E RA TIO N (M ODELS PT-47/53/56WX53, PT-56WX33, PT-53/56TW53  AND PT-4743)
ENG LIS H
Remote Control Operation (models PT-47/53/56WX53, PT-56WX33, PT-53/56TW53 and PT-4743)    
               
Press to turn ON and OFF.
POWER
MUTE
Press to mute sound. Press to display and
cancel CC (Closed Caption).
SAP
 
Press to access audio modes (Stereo, SAP 
or Mono).
TV/VIDEO
Press to select TV or input modes.
Press to select remote operation.
 V C
R DVD
  
  T V
 C B
L DBS
 AUX R C
VR 
D T
V
ACTION
Press to access menus.Press to select next or previous channel and 
navigate in menus.
CH
CH
Press to adjust TV sound and navigate in 
menus.
VOL
  VOL
GUIDE 
DBS functions button.
*PIP MIN
REWPLAY*PIP MAX FF
PAUSESTOPREC
*FREEZETV/VCR *PIP CH
VCR CH*SEARCH
OPEN/CLOSE
*PIP*SPLIT     *MOVE
       *SWAP
*Split or PIP function buttonsComponent function buttons
uPress numeric keypad to select any channel.
7
4
12
5
8
0
9
6
3
R-TUNE
Press to switch to previously viewed 
channel or input modes.
Battery Installation
Use two AA batteries:
Remove battery cover by pushing in and up nea rarrow.
Install batteries matching (+) and (-) polarity signs.
Replace the battery cover.
Note: Incorrect installation can cause battery leakage and
corrosion that will damage the Remote Control
Precautions
•Replace batteries in pairs.
• Do not mix battery types (zinc carbon
with alkaline).
• Do not recharge, heat, short-circuit,
disassemble, or burn batteries.
PROG   
Press to enter minor number in a compound 
number.
RECALL    
Press to display time, channel, sleep timer, 
and other options.
EXIT
DBS functions button.
PAGE
DBS page up/down and DVD skip -/+
buttons. 
LIGHT  
Press to illuminate remote buttons.
ASPECT   
Select picture size (ratio) to match 
programming format.  
EUR7603Z90
BBE
MENU
BBE - Press to turn on or off.
MENU - Press to access DBS or DVD menus.
new2prod 0470-1 E doc2.fm  Page 14  Friday, May 2, 2003  12:31 PM 
						

							REM OTE CO NTR O L OP E RA TIO N (M ODELS PT-47/53/56WX53, PT-56WX33, PT-53/56TW53  AN D PT-4743)
15  l
E NG LIS H
Operating Components with Remote Control
Note: Refer to page 17 for programming Remote Control
procedure.
Operating a VCR
Program the remote control to use with VCR.
Operating a CABLE BOX
Program the remote control to use with Cable Box.  Operating a DBS
Program the remote control to use with DBS.
Operating a DVD
Program the remote control to use with DVD. 
TO DO THIS...PRESS
Turn on/off
Select TV Input mode for VCR
Change Channels up/down
 PIP CH
VCR CH
RecordREC
PlayPLAY
StopSTOP
Fast ForwardFF 
Rewind the TapeREW
PausePAUSE
Change to TV or VCR ModeTV/VCR
 On screen VCR Display RECALL
TO DO THIS...PRESS
Turn on/off
Select a Channel
Change Channels Up/Down
Back to previous channelR-TUNE
Exit menus
POWER
TV/VIDEO
u
POWER
7
4
12
5
8
0
9
6
3
CH
CH
EXIT
TO DO THIS...PRESS
Turn on/off
Display DBS menuMENU
DBS ASPECTASPECT
Menu Navigation
Select a Channel
Program InfomationRECALL
Back to previous channelR-TUNE
Select next page up/downPAGE
Channel Up/Down
PIP CH 
VCR CH
Exit menus
Display program GuideGUIDE
TO DO THIS...PRESS
Turn on/off
Next/Previous Chapter
DVD DisplayRECALL
Skip Search ReverseREW
Skip Search Fast ForwardFF 
PlayPLAY
DVD Open/CloseOPEN/CLOSE
POWER
VOL
  VOLCH
CH
7
4
12
5
8
0
9
6
3
EXIT
POWER
CH
CH
u
new2prod 0470-1 E doc2.fm  Page 15  Friday, May 2, 2003  12:31 PM 
						

							16 l
RE M OTE CO NTR O L OP E RA TIO N (M ODELS PT-47/53/56WX53, PT-56WX33, PT-53/56TW53  AND PT-4743)
ENG LIS H
Operating a DTV Set Top Box
Program the remote control to use with DTV. 
Operating a Cassette Deck
To operate a cassette deck, the remoted control must be in
AUX mode and be programmed with the appropriate code
for your equipment.
Operating a Receiver
Program the remoted to operate audio receiver.  Operating a PVR (Personal Video Recorder)
Program the remote control to use with a PVR.    
TO DO THIS...PRESS
Turn on/off
DTV ASPECTASPECT
Select a Channel
Navigation Left / Right
Back to previous channelR-TUNE
Exit menus
TO DO THIS...PRESS
Turn on/off
Receiver Volume Up/Down
Deck A/BR-TUNE
RecordREC
PlayPLAY
StopSTOP
Fast ForwardFF 
Rewind the TapeREW
PausePAUSE
TO DO THIS...PRESS
Turn on/off
Audio Mute
RCVR. VOl Up Down
Tuner Pre-set stations Up/
Down
POWER
7
4
12
5
8
0
9
6
3
VOL
  VOL
EXIT
POWER
VOL
  VOL
u
POWER
MUTE
VOL
  VOL
CH
CH
To select AV Inputs or
Components:
Press Remote numeric 
keypad
Surround VOL DownPIP MAX
Surround VOL UPPIP MAX 
Center CH VOL Up/DownVCR CH
TO DO THIS...PRESS
Turn on/off
PVR Navigation
Select a Channel
PlayPLAY
RecordREC
PausePAUSE
Back to previous channelR-TUNE
Exit menus
PVR GuideGUIDE
Replay ZonesR-TUNE
Quick SkipOPEN/CLOSE
Return to livePROG  
TO DO THIS...PRESS
AV 1 Press 1
AV 2 Press 2
AV 3 Press 3
AV 4 Press 4
CD Press 5
TUNER Press 6
PHONO Press 7
TAPE Press 8
AUX Press 9
POWER
VOL
  VOLCH
CH
7
4
12
5
8
0
9
6
3
u
EXIT
new2prod 0470-1 E doc2.fm  Page 16  Friday, May 2, 2003  12:31 PM 
						

							REM OTE CO NTR O L OP E RA TIO N (M ODELS PT-47/53/56WX53, PT-56WX33, PT-53/56TW53  AN D PT-4743)
17  l
E NG LIS H
Programming the Remote
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, AUX, RCVR,
TV, DTV CABLE or DBS. Follow the procedures for
programming your Remote Control with or without a code
for the component.
Note: Determine the manufacturer of the component and look
in the table for the code.
Programming with a Code
Procedure
•Confirm that the external component is plugged in
and operating.
• Turn the component off.
•Press   and   together, for at least 5
seconds.
• Press appropriate component button on the
Remote Control VCR, DVD (CD), AUX (VCR2 or
TAPE), RCVR, DTV, CABLE or DBS.
• Enter the 3-digit component code using the
Remote Control numeric keypad (0 - 9 buttons).
•Press the Remote Control   to test the
component. If the procedure was successful, the
component will turnon.
Note: If the component does not operate with the Remote
Control, repeat the procedure using another code.
(Some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming without a Code
This procedure searches all codes and is called the
“sequence method.”
Procedure
•Confirm that the external component is plugged in
and on.
• Turn the component off.
•Press   and   together, for at least 5
seconds.
• Press appropriate component button on the
Remote Control.
•Press VOL u to move forward to the next code.
Press
t VOL to move backward.
•Press the Remote Control   to test the
component. If the procedure was successful, the
component will turn on .
Note:Repeat the above steps until the component code is
found. it may take many attempts before the correct
code is found.
Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all the features found in each
model.
Default Modes for Remote Control
DeviceOperatesDefault
TVTV (Panasonic Only)Panasonic TV Code
DTV-STBDTV (Panasonic Only)Panasonic DTV Code
CABLECABLE (Preset)Panasonic CABLE 
Code 
DBSDBS (Preset) Panasonic DBS Code
VCRVCR (Preset0Panasonic VCR Codes
DVD/CDDVD and CD (Preset)Panasonic DVD Codes
AUXPersonal Video Recorders, Tape and VCR2Panasonic Personal 
Video Recorder Code
RCVRAudio receiver (Preset)Panasonic RCVR code
ACTIONPOWER
POWER
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
     VCR  DVD DVD (CD)   
AUX (VCR2)   AUX (TAPE)   RECEIVER  
CABLE  DBS  
ACTIONPOWER
POWER
new2prod 0470-1 E doc2.fm  Page 17  Friday, May 2, 2003  12:31 PM 
						

							18 l
RE M OTE CO NTR O L OP E RA TIO N (M ODELS PT-47/53/56WX53, PT-56WX33, PT-53/56TW53  AND PT-4743)
ENG LIS H
Component codes 
Codes For VCR   
BrandCode
Admiral335
Aiwa332
Akai314, 315, 316, 329
Audio 
Dynamic311, 339
Bell & Howell305, 313
Broksonic320, 326
Canon323, 325
CCE343
Citizen306
Craig305, 306, 329
Curtis 
Mathes324, 345
Daewoo 301, 324, 343
DBX310, 311, 339
Dimensia345
Emerson303, 319, 320, 325, 
326, 343
Fisher305, 307, 308, 309, 
313
Funai320, 326, 334
GE324, 333, 345
Goldstar306
Gradiente334
Hitachi300, 323, 345
Instant 
Replay323, 324
Jensen339
JVC310, 311, 334, 339
Kenwood306, 310, 311, 339
LXI300, 305, 306,307, 
308, 309
Magnavox323, 324, 331
Marantz310, 311, 339
Marta306
Memorex309, 324
MGA338, 340, 341, 
347,348
Minolta300, 345
Mitsubishi338, 340, 341, 347, 
348
Multitech304, 347
NEC310,311, 334, 339
Olympic323, 324
Optimus306, 321, 328, 335
Orion320, 326
Panasonic321,322, 323, 324
Codes For VCR (Contd.)
BrandCode
Penney300,305, 310, 311, 
324, 339, 345  
Pentax300,311, 345
Philco320, 323, 324, 326, 
331, 343
Philips323, 324, 331
Pioneer323
Proscan300, 301, 302, 323, 
324, 331, 333, 345, 
346
Quasar321, 322, 323, 324
Radio Shack305, 309, 324, 333, 
336, 340
RCA300, 301,302, 323, 
324, 331, 333, 345, 
346
Realistic305, 309, 324, 336, 
340
Samsung302, 304, 333
Sansui320, 326, 339, 352
Sanyo305, 309, 313
Scott301, 302, 304, 309, 
320, 326, 338, 340, 
347, 348
Sears300, 305, 306, 307, 
308
Sharp335, 336
Shintom317
Signature 
2000335
Singer337
Sony328, 329, 330
Sylvania331, 324, 331
Tashiro306
Tatung310, 311, 339
Teac310, 311, 339
Technics321, 322, 323, 324
Teknika324
Toshiba301, 346
Vector 
Research311
Wards306, 309, 335, 336, 
344
Yamaha305, 310, 311, 339
Zenith306,344
Codes For Cable Box
BrandCode
ABC224
Archer225, 232
Cableview205, 232
Citizen205, 222
Curtis212, 213
Diamond224, 225, 232
Eagle229
Eastern234
GCbrand205, 232
Gemini222
General
Instrument/
Jerrold211, 219, 220, 
221, 222, 224, 
225, 226, 227
Hamlin212, 218, 240, 
241, 242, 245
Hitachi203, 224
Macom203, 204, 205
Magnavox233
Memorex230
Movietime205, 232
Oak202, 237, 239
Panasonic209, 210, 214
Philips206, 207, 228, 
229, 230
Pioneer201, 216
Pulsar205, 232
Puser232
RCA215
Realistic232
Regal
212, 218, 240, 
241, 242, 245, 
249
Regency234
Rembrandt205, 232, 237
Samsung205
Scientific 
Atlanta211, 212, 213
Slmark201, 205
Sprucer205, 210
Stargate205, 210
Teleview201, 205
Texscan244
Tocom235
Toshiba204
Unika225, 232
Universal222, 232
Videoway206
Viewstar229, 230
Zenith200, 217
Zenith/.Drake 
Satellite200
Codes For DBS  
BrandCode
Dish Network 
(Echostar)105, 115, 116
Echostar105
Express VU105, 115
G. E.106
G.I. (General 
Instrument)108
Gradiente114
Hitachi103, 111, 
112
HNS (Hughes)103
Magnavox101, 102
Panasonic104
Philips101, 102
Primestar108
Proscan106, 109, 
110, 113
RCA106, 109, 
110, 113
Sony107
Star Choice103, 108
Toshiba100
Uniden101, 102
Codes For DVD
BrandCode
Denon100
Ferguson101
JVC109
Mitsubishi105
Nordmende101
Panasonic100
Philips103
Pioneer102
RCA101
Saba101
Samsung110
Sharp108
Sony104
Technics100
Thomson101
Toshiba103
Yamaha100
Zenith107
new2prod 0470-1 E doc2.fm  Page 18  Friday, May 2, 2003  12:31 PM