Panasonic Hd Projection Television Pt 47xd64 Operating Instructions

							OPTIONAL EQUIPMENT CONNECTIONS
9 z
ENGLISH
HDMI (High Definition Multimedia Interface)
input connection
About HDMI
HDMI is the first all digital consumer electronics A/V
interface that supports several uncompressed standard,
enhanced and high definition video format as well as
existing multi-channel audio format. One jack supports both
video and audio information. The HDMI/HDCP
1 input can
be connected to an EIA/CEA 861
2compliant consumer
electronic device, such as a set top box or DVD player
equipped with a HDMI or DVI output connection. By
inputting a High-bandwidth Digital Content Protection
(HDCP) high definition picture source to the HDMI terminal
of this PTV, high definition pictures can be displayed on the
screen in their digital form. The HDMI input terminal is not
intended to be used with personal computers. This PTV is
compatible with 1080i, 480p and 480i formats. Select the
output of the connecting to device to match that of the PTV.
Notes:
1. HDMI/HDCP = High Definition Multimedia Interface /
High-Bandwidth Digital Copy Protection.
2. EIA/CEA-861 Profiles compliance covers profiles for
transmission of uncompressed digital video including
high bandwidth digital content protection.
Compatible formatsConnection diagram
Follow the diagram below to connect the PTV to a set top box or a
DVD player. 
Procedure
• Connect the HDMI output from the set top box or a DVD
player to the HDMI input on the back of the PTV.
• Press TV/VIDEO button on the remote control to select
HDMI input. The connector on the PTV is HDMI Type A
connector.
• If the external device has DVI output only, use a DVI to
HDMI adaptor cable*
3 to connect to the HDMI jack on
the PTV. Also, connect the Audio Out signal from the
external device (set top box or DVD player) to the Audio
In*
4 jacks below the HDMI input.
• If you cannot display the picture because of your Digital
Set Top Box does not have a Digital Out terminal setting,
use the Component Video Input (or the S-Video Input or
Video Input). In this case, the picture will be displayed as
an analog signal.
Notes:
*3. HDMI-DVI conversion cable (TY-SCH03DH) available
on Panasonic Website: www.panasonic.com.
*4. Please refer to page 23 for Audio setting detail. This PTV is compatible with following formats. Please set 
the connecting device to following format.
Video signal 
Audio signal
When digital audio is included in the HDMI connection, 
the compatible sampling frequencies are 48 KHz / 
44.1Khz / 32 Khz.
FormatNo of dotsVertical scanning 
frequency (Hz)
1080i 1920 x 1080i 59.94 / 60
540p (480p)720 x 480p
640 x 480p59.94 / 60
59.94 / 60
540p (480i) 720 x 480i 59.94 / 60
EXTERNAL DIGITAL COMPONENT
HDMI
AV IN
AUDIO IN
L
R
DVI OUT L- AUDIO OUT - R
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
1INPUT
2INPUT
3PROG
OUTTO AUDIO 
AMP
L
R
AUDIO
VIDEO
Y
P
B
PR
TERMINALS ON BACK OF PROJECTION TELEVISION
L
R
ANT B
AUDIO INL
R
SERVICE
  ONLYHDMI
DIGITAL AUDIO  OUT
Incoming
Cable
EXTERNAL DIGITAL
    COMPONENT
AV IN
 AUDIO  OUTLRHDMI 
OUTCABLES NOT INCLUDED
ANT A
Cable In
CableCARD
INTERFACETM
* The connector on the PTV is HDMI Type A connector.
Connecting devices with DVI out
DVI to HDMI adaptor cable 
						

							10 z
OPTIONAL EQUIPMENT CONNECTIONS
ENGLISH
Digital Audio Out Connection
Use the diagram below to connect the Digital Audio Output of your
HDTV Projection Television to a Dolby Digital decoder.
Digital Audio Out
Dolby Digital 5.1 channel surround sound delivers digital-quality
sound. Dolby Digital provides five discrete full-bandwidth
channels for front left, front right, center, surround left and
surround right, plus a LFE (Low Frequency Effect) subwoofer
channel. For a full Home Theater sound experience, an external
Dolby Digital decoder and a multichannel amplifier must be
connected to the Digital Audio Out jack on the PTV.
Procedure
• Connect the Digital Audio cable from the Digital Audio
Out jack on the PTV to the Digital Audio In connection on
the Dolby Digital decoder.
Note:When ATSC channel is selected, the output from the
Digital Audio Out jack will be Dolby Digital. But, if NTSC
channel is selected, the output will be PCM.
Program Out Connection (PROG OUT)
You can connect a VCR to the PROG OUT terminal to
record the program you are viewing on-screen. An external
monitor can also be connected to the PROG OUT and TO
AUDIO AMP terminals. Connect the VCR as shown below. 
Procedure
• Connect the VCR to PROG OUT and TO AUDIO AMP
terminals
• PROG OUT terminal display is the same as on-screen
display.
• See the VCR instruction manual for further instructions
for recording the program.
Notes:
• This TV contains Video and Audio Outputs for the
purpose of recording television programming to VCR.
Due to license restrictions, if a device (STB, DVD, etc.) is
connected to the HDMI input of the TV, no video or audio
output is allowed. • Program Out signal may not be available when
component input is selected for main picture.
• Program Out signal is available when receiving digital
channel. However, all digital formats are down converted
to composite NTSC video.
• When receiving digital or analog channels signals and
the analog or digital CC is ON, Program Out connector
will output open caption text in the NTSC video picture. If
CC is OFF, only analog CC closed caption code is
passed out the Program Out connector.
• Certain program content output from the Program Out
connector may have the Macrovision signal modification
applied to its signal, preventing VCRs from recording this
video signal.
Amplifier Connection (Analog) 
To listen the audio through a separate stereo system,
connect an external audio amplifier TO AUDIO AMP
outputs on back of television.
Note:TO AUDIO AMP terminals cannot be connected directly
to external speakers. 
Audio Adjustments
• Select Speakers Off in Audio Other Adjust menu.
• Set amplifier volume to the preferred level. 
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
1INPUT
2INPUT
3PROG
OUTTO AUDIO 
AMP
LRAUDIO
VIDEO
Y
P
B
PR
TERMINALS ON BACK OF PROJECTION TELEVISION
L
R
ANT B
AUDIO INL
R
SERVICE
  ONLYHDMI
DIGITAL AUDIO  OUT
CABLES NOT SUPPLIED
A/V IN
90.7 MHZ
OPTICAL IN
Amplifier Six channel Speaker system
ANT A
Cable In
CableCARDTMINTERFACE
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
1INPUT
2INPUT
3PROG
OUTTO AUDIO 
AMP
L
R
AUDIO
VIDEO
Y
P
BPR
TERMINALS ON BACK OF PROJECTION TELEVISION
L
R
ANT B
AUDIO INL
R
SERVICE
  ONLYHDMI
DIGITAL AUDIO  OUT
CABLES NOT SUPPLIED
A/V IN
VCRPLAY
STOP R
E
WFF
ANT IN 
ANT OUTVIDEO L -  AUDIO - R
INOUT
ANT A
Cable In
CableCARD
INTERFACETM
CABLES NOT SUPPLIED
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
1INPUT
2INPUT
3PROG
OUTTO AUDIO 
AMP
LRAUDIO
VIDEO
Y
P
B
PR
TERMINALS ON BACK OF PROJECTION TELEVISION
L
R
ANT B
AUDIO INL
R
SERVICE
  ONLYHDMI
DIGITAL AUDIO  OUT
A/V IN ANT A
Cable In
90.7 MHZ
EXTERNAL AMPLIFIER
CableCARD
 INTERFACETM 
						

							PIP AND SPLIT OPERATION
11 z
ENGLISH
PIP and SPLIT Operation
PIP Operation
This television includes a two-tuner Picture In Picture (PIP)
feature. This allows you to watch two (2) live broadcasts at
the same time with or without an external video source
such as a VCR, cable box, etc.
Note:Only the Analog programming from Antenna (A) and video
inputs signal can be viewed in the PIP/SPLIT frame.
Procedure
• Connect incoming cable to ANT (A) input on back of TV.
• Press   to display PIP frame.
• Select channels for the PIP frame by pressing
.
• Select channels for the Main picture by pressing
or use the remote control numeric keypad.
• Press  to switch the PIP and MAIN PICTURE
source.
• Press  to view picture source status. 
• Press   to cancel PIP frame.
Split Operation
This feature lets you watch two different channels side by
side with or without an external video source.
Procedure
• Press   to display Split screen.
• Select channels for the Split by pressing  .
• Select channels for the Main picture by pressing
or use the remote control numeric keypad.
• Press  to switch the SPLIT SCREEN and MAIN
PICTURE source.
• Press  to view picture source status.
• Press   to cancel Split screen.
Note:PIP or SPLIT frame cannot display digital channel signal. You
can display digital channel as the Main picture and analog
channel in PIP/SPLIT frame or analog channels in both Main
and PIP/SPLIT frame. Swap is possible when both Main picture
and PIP/SPLIT picture are analog channels or video input
sources.
PIP and Split Operational Buttons
TV/VIDEO Button 
Press when PIP or Split frame is displayed to select
desired input mode.   
Search Button (PIP and Split)
This feature lets you scan through all available analog
channels.
Procedure
• Press   or   to display PIP or Split frame.
• Press   to display search frames.
Note:When the main picture is ATSC (terrestrial) digital
channel, the search feature is unavailable. Search
feature is available only for analog channels.
• Press  again to stop search feature. PIP or
Split frame channel will be the last active search frame.
• Press   or   to cancel PIP or Split frame 
PIP
     PIP CH
DVD/VCR CH
or
CHCH
SWAP
 
REC
A
LL
PIP
Note:Audio is from Main Picture only.
Main Picture
PIP Frame
SPLIT
     PIP CH
DVD/VCR CH
or
CHCH
SWAP
 R
ECA
LL
SPLIT
PIP Frame
Main Picture
CH #
COMPONENT1COMPONENT2
HDMI
VIDEO 1/2/3/4
Main Picture
CH #
SPLIT FrameCOMPONENT1COMPONENT2
HDMI
VIDEO 1/2/3/4
PIPSPLIT
SEARCHOPEN/CLOSE
SEARCHOPEN/CLOSE
PIPSPLIT
2
3
4
Search Frames Main Picture 
						

							12 z
PIP AND SPLIT OPERATION
ENGLISH
Move Button (PIP only) 
This feature is used to move PIP frame to one of four
corners.
Procedure
• Press   to display PIP frame.
• Press   to position PIP frame to desired corner.
• Press   to cancel PIP frame. 
PIP MIN and PIP MAX Buttons
While PIP frame is displayed, press PIP MIN or PIP MAX
button to vary the size of PIP frame.
Procedure
• Press   to display PIP frame.
• Press   or   to size PIP frame.
• Press   to cancel PIP frame.
Freeze Button (PIP and Split) 
This feature is used to stop action in PIP or Split frame.
Procedure
• Press   or   to display PIP or Split frame
• Press   to stop PIP or Split frame action. 
• Press   again to continue action. 
• Press   or   to cancel PIP frame.      
Main Picture Freeze Feature
This feature is used to stop action of the Main Picture and
display it on a Split or PIP freeze frame.
Procedure
• To stop action for Main picture, press   while
PIP or Split frame is not displayed.
• Main Picture freeze will be displayed in a PIP or Split
frame, depending on the selection in the Freeze menu
located in Picture Other ADJ. section (refer to page 20).
• Press   again to cancel Main Picture freeze
frame.
Note:While Main Picture freeze frame is displayed, only
MOVE button is active for PIP, all other PIP and Split
buttons have no effect (see chart).
PIP, Split and Freeze Mode Buttons Operational chart
This chart indicates the buttons that are operational with 
PIP, Split or Main Picture Freeze mode.      
PIP
 MOVE
PIP
PIP Frame
Main Picture
PIP
 PIP MIN PIP MAX
PIP
Main PictureMAX
MIN
PIPSPLIT
FREEZETV/VCR
FREEZETV/VCR
PIPSPLIT
Main PictureMain Picture
PIP freeze frame
Note:Audio is from Main Picture only.Split freeze frame
REMOTE 
BUTTONSPIP MODESPLIT MODE
MAIN 
PICTURE
FREEZE 
MODE
PIP MINSize SmallerNo EffectNo Effect
PIP MAXSize LargerNo EffectNo Effect
FREEZEFreeze PIP 
frameFreeze Split 
FrameDisplay or 
Delete
PIP CHChange 
ChannelChange 
ChannelNo Effect
SEARCH
Displays 
Search Frame
(not available 
when Main 
picture is 
digital)Displays 
Search frame
(not available 
when Main 
picture is 
digital)
No Effect
PIPDelete PIP 
FrameDisplays PIP 
frameNo Effect
SPLITDisplays Split 
FrameDelete Split 
frameNo Effect
MOVEMove PIP 
FrameNo EffectMove PIP 
Frame
SWAP
Swap with Main 
Picture (not 
available when 
main picture is 
digital channel)Swap with 
Main Picture 
(not available 
when main 
picture is 
digital 
channel)
No Effect
FREEZETV/VCR
FREEZETV/VCR 
						

							SPECIAL FEATURES OF THE HIGH DEFINITION PROJECTION TELEVISION
13 z
ENGLISH
Special Features of the High Definition Projection Television
Channel and Program Tuning
Channel and Program tuning in digital television is different from
current conventional television. In DTV, multiple programs can
exist within a single 6MHZ channel. These channels behave as
sub-channels within a single channel. When tuning to a digital
channel, the HDTV Projection Television will also tune to a
program. The HDTV Projection Television will indicate the channel
and program using the on-screen Channel Banner display.
Note:In order to select channels properly, Auto Scan must be
performed (refer to page 27).
Tuning digital and analog channels
You can tune the digital and analog channels in the following
ways:
ˆDirect tuning (0 - 9 keys) - using the numeric keys on the
Remote control to directly input the Channel number. If
necessary, use the   button to enter the program number of
the digital channel.
ˆChannel Up/Down Tuning (CH S or CH Tbuttons) - Tunes
to the next or previous available channel or program. The
Channel Up/Down tuning depends upon the surfing mode
(see pg. 21) you have set in the Channel menu.
ˆRapid Tuning (R-TUNE) - Switches between the last two
channels or programs.
Direct Tuning Method
Follow the procedure below to directly enter the channel number
using the Remote Control numeric keys.
Procedure
• Press the numeric keys on the Remote Control to enter
the Channel number. Press OK button.
• If tuning a digital channel and your channel contains
more than one program, press the   button and enter
the program # (1, 2, 3 etc.) using the numeric keys.
Press OK button. The following is an example of tuning
to channel 15-1.
The HDTV Projection Television will tune to channel 15-1.
Channel Banner: Minimized
The minimized Channel Banner will display the antenna input,
channel number, and the station identification (if available).
Channel Banner: Maximized
Press the RECALL button to display the maximized channel
banner. While the channel banner is displayed, you can add the
channel to Favorite channel list or delete the channel from the
Favorite channel list.   
Add Fav / Del Fav feature
This feature lets you add channels to Favorite channel list or
delete channels from Favorite channel list.
Procedure
• Tune the desired the channel to be added or deleted.
• Press the RECALL button to display the Channel
Banner.
• Press the OK button to execute your choice.
Emergency Alert System (EAS) Forced Tuning
If a CableCARD™ module is installed, the cable MSO (multiple
system owner/operator) may provide an Emergency Alert System
message. These messages are intended to alert the general
public of important local or national emergency situations. In the
event of receipt of one of these messages, the HDTV Projection
Television shall immediately tune to the channel as directed by the
EAS message. If the channel has blocked using the parental
control, the parental blocking has priority over the forced tune.Direct Tuning Example
StepActionChannel Banner 
Display
1Press 1 1
2Press 5 15
3
Press 15-
4Press 1 15-1
5 Press OK15-1
A: 15-1
KPBS-HD
12:30 pm
30
Clock
Time remaining
in Sleep Timer
Audio Track 1 of 1 (English)
Audio Track of 
digital channel
A: 15-1
 KPBS - HD
Add FAV
TV-G1080iVIVID
Antenna designation,
Channel and program #
and Station identifierRating
indicationPicture mode 
setting
Closed Caption and
SAP indication
Add FAV or 
Del FAV button
SAPCCHDMI
PIP/SPLIT CH# or 
Input information
FULL
Program Aspect Signal Format 
						

							14 z
SPECIAL REMOTE BUTTONS
ENGLISH
Special Remote Buttons
ASPECT Button 
The ASPECT button on the remote control lets you choose
one of four display modes, depending on the formats of the
received signal and your preferences. BBE Button
Press this button to turn BBE VIVA 3D sound feature (available on 
PT-53TWD64) or BBE sound feature (available on PT-47XD64
and PT-53XD64) On or Off.
SAP Button
Press this button to select the next audio track (if available) when
receiving a digital channel. 
In analog mode, press this button to cycle through different audio
modes. For example:
• If receiving STEREO, SAP and MONO or receiving
STEREO and MONO only, pressing SAP button,
will toggle the audio as follows:
PROG button
When tuning digital channel, press the   button to enter the
minor number in a compound channel number.
MENU button
Press to display the Main menu or return one step backward in
menus.
RECALL button
Press this button to display or remove the channel banner. 
R-TUNE Button
Customer Options depending on Input Signal Format
INPUT
SIGNAL DISPLAY ON SCREENASPECT BUTTON 
OPTIONS
1080i16:9 onlyNo options
480p (16:9)Default to 16:94:3, Full or Zoom (see 
below)
480p (4:3)Default to FULL mode.4:3, Full or Zoom (see 
below)
480iDefault to JUST mode4:3, Full, Just or 
Zoom (see below)
Input SignalASPECT
4
3
Image on 
16:9 Screen Size
4:3
480i or 480p
This will display a 4:3 picture
at its standard 4:3 size with
gray side bars. (Not
recommended for viewing
4:3 pictures as it may create
a permanent image on
screen if displayed for a
prolonged period of time.)
480i  or 480p
Input SignalASPECTImage on 
16:9 Screen Size
ZOOM
16
9
This will expand the 4:3 
picture uniformly (width and 
height) to full screen width 
and then reposition the 
picture vertically. 
(Recommended for letterbox 
pictures.)
480i  or 480p
Input SignalASPECTImage on 
16:9 Screen Size
FULL
16
9
This will show picture at full 
screen size. (Recommended 
for anamorphic pictures.)
Input SignalASPECTImage on 
16:9 Screen Size
480i
JUST
16
9
This will stretch the right and 
left edges of a 4:3 picture to 
fill the screen, The center of 
the screen will have aspect 
correction applied. The size 
of the picture will depend on 
the original signal. 
(Recommended for regular 
TV viewing.)
Audio Track 1 of 1 (English)
STEREO JSAP JMONO
PROG 
						

							REMOTE CONTROL OPERATION
15 z
ENGLISH
Remote Control Operation
10
 1
 2
 4
 3
 5
 7
 6
 8
 9
11
12
13
14
15
16
18
17
19
20
21
22
23
24
25
26
27
28
30
29
31
32
EUR7627Z10
 BUTTON
NUMBERDESCRIPTION
Press to choose menu and sub-menu entry.
Press to display Main Menu or return one step 
backward in menus.
Press numeric keypad to select any channel or press to 
enter alphanumeric input in menus.
Press to switch to previously viewed channel or input 
mode.
 PIP MIN - While remote is in TV mode, press to 
decrease the PIP size.
REW - While remote is in VCR or DVD mode, press to 
rewind. 
  While remote is in VCR or DVD mode, press to play. 
While remote is in VCR or DVD mode, press to 
pause. 
FREEZE - While in TV mode, press to stop action in 
the PIP or Split frame.
TV/VCR - Press to switch to TV or VCR.
Press to display or delete PIP frame.
Press to display or delete Split frame.
In analog mode, press to access audio modes (Stereo, 
SAP or Mono). In digital mode, press to access next 
audio track.
Press to illuminate remote buttons. 
Press to switch to (A or B) RF antenna input.
Press to turn BBE OFF or ON.
Press to display or delete Channel banner.
Press to exit menus.
Press to change channels and navigate in menus.
Press after entering major channel numbers to enter 
minor (-) channel numbers.
PIP MAX - While in TV mode, press to increase the PIP 
size.
FF - While in VCR or DVD mode, press to fast 
forward. 
While remote is in VCR mode, press to record.
While remote is in VCR or DVD mode, press to stop.
SEARCH - Press to scan available channels in 
search frames. Press again to delete search frames.
OPEN/CLOSE - Press to open or close DVD tray.
Press to change channels for PIP or VCR. 
Press to swap Main picture with PIP or Split frame.
While PIP frame is displayed, press to move to one 
of four corners. 
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
 BUTTON
NUMBERDESCRIPTION
Press to turn ON and OFF.
Note:The ON/OFF indicator LED (red) will be lit
when set is on.
Press to select remote operation.
Press to select (Component 1or 2), (HDMI), 
(Video 1, 2, 3 or 4) input mode or TV mode.
Press to access Photo Viewer™.
 Also press while Photo Viewer™ is displayed to 
access Photo Viewer™ set up menu. 
Press to select picture size (ratio) to match 
programming format.
Also used for Photo Viewer™ to change aspect 
of the image on-screen.
Press to mute sound. Press to display and 
cancel CC (Closed Caption).
 Press to adjust TV sound and navigate in 
menus.
 1
 2
 3
 4
 5
 6
 7 
						

							16 z
REMOTE CONTROL OPERATION
ENGLISH
Programming The Remote Control
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, DBS, RCVR or
AUX. Follow the procedures for programming your Remote
Control with or without a code for the component.
Note:Determine the manufacturer of the component and look
in the table for the code (found on pages 17~18).
Procedure
1. Confirm that the external component is plugged and
operating.
2. Turn the component off.
3. Press  and  together, for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the OK
and POWER buttons.
4. Press appropriate component button on the Remote
Control VCR, DVD (CD), DBS, RCVR, CBL or AUX
(PVR or VCR2). The component button will illuminate
steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control   to test the component.
If the procedure was successful, the component will
turn on and the component key will blink twice and then
go out.
Note:If the component does not operate with the Remote
Control, repeat steps 3 through 6 using another code.
(Some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming Without A Code
This procedure searches all codes and is called the
“sequence method.”
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
3. Press  and 
 together, for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the OK
and POWER buttons.4. Press appropriate component button on the Remote
Control.
5. Press the   button to set the remote control into the
step and set mode.
6. Point the remote control towards the component.
7. Press VOL X(the mode key will blink three times), then
press the Remote Control   to test the component.
Continue this process until the proper code is found. If
the procedure was successful, the component will turn
on.
Note:Each time you press the VOLX button, make sure that
the component key blinks twice before pressing the
POWER button. 
8. Once the device responds, press   to store the
code. The mode (component) button will blink twice.
Note:It may take many attempts before the correct code
is found. If you miss a code, press WVOL, then press the
button to test the component.
Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.
DeviceOperatesDefault
TVTV (Panasonic Only)Panasonic Code
VCRVCR (Preset)Panasonic Code 
DVD/CDDVD and CD (Preset) Panasonic Code
DBSDBS STB & CBL STB (Preset)Panasonic DBS Code
RCVRAudio Receiver (Preset)Panasonic RCVR Code
CBLCable (Preset)Panasonic CABLE 
Code
AUXPersonal Video Recorders, 
Cassette and VCR2Panasonic Personal 
Video Recorder Code
OK
POWER
POWER
OK
POWER
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
     VCR DVD DVD (CD)  
 DBS  RECEIVER CABLE  
 AUX (PVR)  AUX (VCR2) 
POWER
POWER
OK
POWER 
						

							REMOTE CONTROL OPERATION
17 z
ENGLISH
Codes For VCR   
BrandCode
Admiral335
Aiwa332
Akai314, 315, 316, 329
Audio 
Dynamic311, 339
Bell & Howell305, 313
Broksonic320, 326
Canon323, 325
CCE343
Citizen306
Craig305, 306, 329
Curtis 
Mathes324, 345
Daewoo 301, 324, 343
DBX310, 311, 339
Dimensia345
Emerson303, 319, 320, 325, 
326, 343
Fisher305, 307, 308, 309, 
313
Funai320, 326, 334
GE324, 333, 345
Goldstar306
Gradiente334
Hitachi300, 323, 345
Instant 
Replay323, 324
Jensen339
JVC310, 311, 334, 339
Kenwood306, 310, 311, 339
LXI300, 305, 306, 307, 
308, 309
Magnavox323, 324, 331
Marantz310, 311, 339
Marta306
Memorex309, 324
MGA338, 340, 341, 347, 
348
Minolta300, 345
Mitsubishi338, 340, 341, 347, 
348
Multitech304, 347
NEC310, 311, 334, 339
Olympic323, 324
Optimus306, 321, 328, 335
Orion320, 326
Panasonic321, 322, 323, 324
Penney300, 305, 310, 311, 
324, 339, 345 
Pentax300, 311, 345
Codes For VCR (Contd.)
BrandCode
Philco320, 323, 324, 326, 
331, 343
Philips323, 324, 331
Pioneer323
Proscan300, 301, 302, 323, 
324, 331, 333, 345, 
346
Quasar321, 322, 323, 324
Radio Shack305, 309, 324, 333, 
336, 340
RCA300, 301, 302, 323, 
324, 331, 333, 345, 
346
Realistic305, 309, 324, 336, 
340
Samsung302, 304, 333
Sansui320, 326, 339, 352
Sanyo305, 309, 313
Scott301, 302, 304, 309, 
320, 326, 338, 340, 
347, 348
Sears300, 305, 306, 307, 
308
Sharp335, 336
Shintom317
Signature 
2000335
Singer337
Sony328, 329, 330
Sylvania323, 324, 331
Ta s h i r o306
Tatung310, 311, 339
Teac310, 311, 339
Technics321, 322, 323, 324
Te k n i k a324
To s h i b a301, 346
Ve c t o r  
Research311
Wards306, 309, 335, 336, 
344
Yamaha305, 310, 311, 339
Zenith306,344
  
Codes For Cable Box
BrandCode
ABC124
Archer125, 132
Cableview105, 132
Citizen105, 122
Curtis112, 113
Diamond124, 125, 
132
Eagle129
Eastern134
GCbrand105, 132
Gemini122
General
Instrument/
Jerrold111, 119, 
120, 121, 
122, 124, 
125, 126, 
127
Hamlin
112, 118, 
140, 141, 
142, 145
Hitachi103, 124
Macom103, 104, 
105
Magnavox133
Memorex130
Movietime105, 132
Oak102, 137, 
139
Panasonic109, 110, 114
Philips
106, 107, 
128, 129, 
130
Pioneer101, 116
Pulsar105, 132
Puser132
RCA11 5
Realistic132
Regal
112, 118, 
140, 141, 
142, 145, 
149
Regency134
Rembrant105, 132, 
137
Samsung105
Scientific Atlanta111, 112, 113
Slmark101, 105
Sprucer105, 110
Stargate105, 110
Te l e v i e w101, 105
Texscan144
To c o m135
To s h i b a104
Unika125, 232
Universal122, 132
Codes For Cable Box (Contd.)
BrandCode
Videoway106
Viewstar129, 130
Zenith100, 117
Zenith/.Drake 
Satellite100
Codes For DBS  
BrandCode
Dish Network 
(Echostar)105, 115, 116
Echostar105
Express VU105, 115
G.  E .106
G.I. (General 
Instrument)108
Gradiente11 4
Hitachi103, 111, 
11 2
HNS (Hughes)103
Magnavox101, 102
Panasonic104
Philips101, 102
Primestar108
Proscan106, 109, 110, 
11 3
RCA106, 109, 
110, 113
Sony107
Star Choice103, 108
To s h i b a100
Uniden101, 102
Codes For DVD
BrandCode
Denon100
Ferguson101
JVC109
Mitsubishi105
Nordmende101
Panasonic100
Philips103
Pioneer102
RCA101
Saba101
Samsung11 0
Sharp108
Sony104
Te c h n i c s100
Thomson101
To s h i b a103
Yamaha100
Zenith107 
						

							18 z
REMOTE CONTROL OPERATION
ENGLISH
Component Codes (Cont.)
  
Codes For CD Players  
BrandCode
Admiral226
Aiwa233, 235
Carver229
Denon242
Emerson239
Fisher205
Harman/Kardon219, 220, 
221, 223
Hitachi207
Jensen234
JVC240, 241, 245
Kardon223
Kenwood200, 201, 211, 
245
LXI/Sears236
Magnavox229, 232
Marantz229
McIntosh221
Nakamichi210
Onkyo214, 215
Optimus208, 218, 
220, 222
Panasonic224, 225, 227
Philips229, 230
Pioneer208
Quasar224, 225, 227
RCA231, 237, 
238, 247
Sansui210, 246
Sanyo205
Scott210, 246
Sharp242, 243
Sherwood220
Sony228
Soundesign244
Te a c212, 216, 218
Technics224, 225, 227
Victor240, 241, 245
Ya m a h a202, 203, 204
Codes For Personal Video 
Recorders
BrandCode
Panasonic Replay 
TV100
Philips Tivo102
Sony Tivo101
Codes For Cassette Decks   
BrandCode
Aiwa223, 224, 225
Denon231
Fisher203
Jensen214
JVC229, 230
Kenwood200, 207
Marantz202
Nakamichi205
Onkyo208, 209, 213
Panasonic216, 218
Philips222
Pioneer204
RCA226, 227, 228
Sansui205, 210
Sharp231
Sony219, 220
Te a c210, 211, 215
Technics216, 218
Ya m a h a201, 202
Codes For Receivers 
BrandCode
Admiral120
Aiwa125, 126
Denon134, 135, 136
Fisher104
Garrard11 3
Harman 
Kardon115, 123
Jensen129
JVC132, 133
Kenwood100, 108
Magnavox127
Marantz124
Mclntosh11 6
Nakamichi106
Onkyo109, 114
Optimus 103, 127, 130, 
131
Panasonic118, 119, 121
Philips123
Pioneer105, 107
Quasar118, 119, 121
RCA103, 105, 127, 
130, 131
Sansui103, 111, 139
Sharp134, 137
Sony122
Soundesign138
Te a c111 ,  11 2 ,  11 3
Technics118, 119, 121
Victor132, 133
Ya m a h a101, 102