Panasonic Hd Integrated Camera Aw He2_adv Operating Instructions

- 41 -
Maintenance screen
You can perform such operations as displaying the unit information, restoring the unit’s 
default settings.
A[Information] tab
B [Other] tab
Click the [Information] tab on the Maintenance screen.≥The model number ([Model no.]), MAC address ([MAC address]), and firmware version 
([Firmware version]) of the unit, and the user who last logged into the Setup screen 
([Access log]) are displayed.
∫ To check the firmware version on the camera menu
To display the unit information on...

- 42 -
Click the [Other] tab on the Maintenance screen.
≥
The Other screen opens.
You can restore the unit’s default settings. (The settings for the Network screen, the User 
mng. screen and  the system frequen cy do not change)
Click [Execute].≥A confirmation message is displayed. Click [OK].
∫ Setting Using the Camera Menu
≥A confirmation message is displayed. Select [YES].
To configure the settings on the Other Screen
[Reset to the default (Except the network settings)]
[MAINTENANCE]  # [INITIAL SET] 

- 43 -
Change the image displayed on the HDMI output monitor or the web setting screen.
Select your desired item and click [Execute].
≥You can also switch the display between the camera image and the color bars by pressing 
the MODE button on the wireless remote controller or the controller.
≥ The color bar type differs depending on the system frequency setting.
You can set whether to show/hide the guideline display.
Select your desired item and click [Execute].
∫ Setting Using the Camera Menu
You can...

- 44 -
Setting Using the Camera Menu
≥The following items can only be set from the camera menu:
You can set whether to show the menu screen and the status display of the White Balance 
Setting when the unit receives a tally light-up signal.
You can update the firmware of the unit.
≥ After contacting the store of purchase, save the latest firmware on to a microSD card 
(always check the precautions of the store of purchase before following any 
instructions).
1 Insert a microSD card containing an update...

- 45 -
∫
It is not a malfunction in following cases
Troubleshooting
Object seems to be 
warped. ≥
Object seems to be warped slightly when the object 
moves across the image very fast, but this is because the 
unit is using MOS for the image sensor. This is not a 
malfunction.
When the flash is fired 
during shooting, only 
the top or bottom of the 
screen becomes lighter. ≥
With a MOS image sensor, the shooting timing differs 
slightly between the top left and bottom right of the 
screen. This means that...

- 46 -
Wireless remote controller
ProblemCheck points
Cannot operate.≥Check if the status display lamp is lit green and the unit is 
turned on.
≥ Before operating, select the unit by pressing one of the 
CAM1 to CAM4 buttons.
≥ When strong light from a fluorescent lamp, a plasma 
monitor, the sun, etc. is shining on the wireless remote 
control signal light-sensing area, the unit may not 
respond.
≥ If the status display lamp does not blink even when you 
operate near the wireless remote control signal...

- 47 -
Web setting screen
ProblemCheck points
The web setting screen 
cannot be accessed.≥
Turn on the unit or set it to Standby mode.
≥ Check if a valid IP address is set for the unit. 
≥ After changing the IP address of the unit, enter [http:// 
Post-change IP address/] into the address bar of the web 
browser.
≥ Make sure that you do not access a wrong IP address.
j[When using Windows]
Execute the Windows command prompt, ping [The IP 
address set for the unit]. If a reply comes back from the 
unit,...

- 48 -
The settings on the web 
setting screen or the 
image on the camera is 
not updated or displayed 
properly.≥
The unit’s ports may be filtered by the firewall or other 
function of the anti-virus software.
Change the HTTP port number of the unit to a port 
number which will not be filtered.
[When using Windows]
≥ Press the [F5] key on the personal computer keyboard 
and update the display.
≥ Follow the steps below to delete the temporary Internet 
files.
1) In Internet Explorer, click [Tools]  #...

- 49 -
Video
ProblemCheck points
No pictures are 
displayed or the pictures 
are disturbed.≥
Check if the unit is correctly connected with other 
devices.
≥ If your system is configured in such a way that a 
displayed image is automatically switched in conjunction 
with your camera selection, select the correct camera.
≥ Check if [Format], [Down CONV. Mode], and [System 
Frequency] are set correctly. ( l34, 35)
The picture is flipped 
vertically. ≥
Turn the middle ring portion by 180° so that the...

- 50 -
Precautions when using a computer
When using a computer, the symptoms described below may occur.
If any of them occurred, follow the instructions to solve each problem.
(The instructions describe solutions for administrators.)
≥Descriptions in this document are based on operation check by Panasonic Corporation.
Possible symptoms may vary depending on platforms or operating system versions, etc.
Operating procedures and screen are described using Windows 7 and Internet Explorer 9.0.
∫ When...