Panasonic Electronic Board Ub-8325 Operating Instructions

Installing Drivers and Software
31
Using
If you need to remove the USB driver, printer driver, 
TWAIN driver and Interactive Panaboard Software, 
perform the following steps.
1Power on your computer and start Windows.
•Log on as an administrator for 
Windows 2000 or Windows XP.
2Click [Start], and then click Control Panel in 
Settings.
•For Windows
 XP, click [start], and then click 
Control Panel.
3Double-click Add / Remove Programs icon 
(Windows XP: Add or Remove Programs) in 
the Control Panel....

Using the Panaboard in Projector Mode
32
•When using a projector to project images, be sure to display the image so that it is centered left-to-right on the 
Interactive Panaboard screen and with at least a 50 mm  (2”) gap between the top of the image and the screen 
border. Note that the Electronic Pen does not always operate properly when within 50 mm (2”) of the top of the 
screen, 100 mm (3 
15/16”) of the position receiver and 35 mm (1 3/8”)  from the both sides of the screen.
•Since the Electronic...

Using the Panaboard in Projector Mode
33
Using
1Turn on the Interactive Panaboard.
2Turn on your computer and start up Windows.
3For Windows 2000 / Windows XP
Connect the USB cable provided from the 
electronic board to the computer.
•The Interactive Panaboard Software is 
automatically started.
For WIndows 98 / Windows Me
Click [Start] and select Programs - 
Panasonic - Interactive Panaboard - 
Interactive Panaboard.
•The window appears to show the Interactive 
Panaboard is detected.
Note
•If the...

Using the Panaboard in Projector Mode
34
•When the calibration is 
completed and the Projector 
mode become active, the icon 
 will be registered in the 
Taskbar and the Desktop 
Drawing Tool will appear 
automatically.
[Desktop Drawing Tool]
Note
•If the Interactive Panaboard is not detected, 
the following notification window appears. 
In this case, check the status of the 
Interactive Panaboard and confirm that the 
USB cable is connected. For details on the 
settings of the communications port, refer...

Using the Panaboard in Projector Mode
35
Using
■Switching the Mode
You can freely switch the Projector mode and the 
Whiteboard mode while the Interactive Panaboard 
Software is running.
1Right-click the icon   in the Taskbar and 
click Select Mode... in the pop-up menu. In 
addition, you can double-click the icon in the 
Ta s k b a r.
•The Select Mode window appears.
2Click Projector or Whiteboard icon, and then 
click [OK].
Note
•When switching to the Projector mode, the 
calibration screen will not be...

Using the Panaboard in Projector Mode
36
■Adjusting the Shifted Position
The Electronic Pen or Electronic Eraser position may 
largely shift by the using environment. In this case, 
adjust the position according to the following 
procedures to improve the shifted position.
1Right-click the icon   in the Taskbar and 
click Settings - Adjustment... in the pop-up 
menu.
•The Adjustment window appears.
2Place the Electronic Pen at the center of the 
Interactive Panaboard screen and drag slowly 
the...

Using the Panaboard in Projector Mode
37
Using
•JPEG:
Sets the quality level when exporting a page 
as a JPEG format image file. The larger 
number will get higher quality for the image 
file than small number when exporting. 
However, the file size will be large.
•TIFF:
When exporting a page as a TIFF format, an 
image file is compressed by checking the 
Compression (PACKBITS) check box.
•Save file automatically, named with the 
date:
The image file will be saved automatically as 
a file named with the...

Using the Panaboard in Projector Mode
38
Note
•If you move the projector or Interactive 
Panaboard, the position of the computer 
screen projected onto the Interactive 
Panaboard screen will be moved. This will 
result in out of position of the Electronic Pen. 
If this happens, you will need to calibrate the 
unit again by executing Calibrate in the pop-
up menu from the Toolbar.
•In the Projector mode, use the Electronic 
Pen with its cap on.
•Do not cover the position receiver with your 
hand as this...

Using the Panaboard in Projector Mode
39
Using
Step 3: Recording image and lines 
data on the Desktop
Data of lines drawn or erased on the Desktop using 
the Desktop Drawing Tool can be recorded in 
Interactive Panaboard format files (extension “.ipb”, 
referred to as IPB documents).
There are two methods to record drawings. To select 
the recording method, refer to “Setting Options” on 
page 36.
The following is (Method 2) Record strokes and 
background image together. For more details on 
recording...

Using the Panaboard in Projector Mode
40
The Desktop Drawing Tool is a tool for 
drawing, erasing, recording, etc. on the 
Desktop.
Right-click the icon   in the Taskbar 
and click Tool - Draw in the pop-up 
menu. The Desktop Drawing Tool will 
appear and check mark is placed next 
to the Draw menu. Clicking Draw again 
will delete the check mark and 
disappear the Desktop Drawing Tool.
The Desktop Drawing Tool is always 
displayed at the front of the Desktop. 
From this Desktop Drawing Tool, the 
tools...