Panasonic Electronic Board Ub-8325 Operating Instructions

Making Copies
21
Using
This section describes how to copy text and 
illustrations drawn on the screen.
1
Set the power switch to on ( I ).
•“ ” will light on the Multi-Copy/Error 
Indicator to indicate that the unit is ready to 
copy.
•The screen will move to home position and 
stop.
2
Press the   (Copy Key).
•Text and illustrations on the screen will be 
copied and copies emerge from the output 
port.
•The output port can hold up to 10 sheets of 
copy paper. (Note that exceeding the output 
port’s...

Replacing the Thermal Transfer Film
22
The unit is capable of producing about 15 more copies 
when the Contrast/Remaining Film Indicator begins to 
flash. The unit has run out of thermal transfer film and 
can no longer make copies when the Multi-Copy/Error 
Indicator flashes “ ”. Separately available 
replacement film (UG-6001) may be purchased from 
the dealer where you purchased the unit. Thermal 
transfer film is replaced as follows.
Notes on Replacing Thermal 
Transfer Film
•Only use the designated...

Paper Jams
23
Using
Remove paper jams by the following procedure when 
copy paper does not come out of the output port or 
when “” flashes on the Multi-Copy/Error Indicator.
1
Push down the printer open lever to open the 
printer door.
2
Remove the thermal transfer film with both 
hands.
3
Remove the jammed paper.
4
Install the thermal transfer film.
•Refer to steps 3 and 4 in the section of 
“Installing the Thermal Transfer Film” on 
page 18.
•“ ” flashing on the Multi-Copy/Error 
Indicator will go...

Paper Jams
24
3
To prevent paper jams such as those caused 
by multiple sheets feeding at once, fan the 
paper thoroughly, square it, align it with the 
guide inside, and insert as far as it will go.
Note
•Do not stack more copy paper in the unit 
than the maximum paper limit indicated by 
the guide (see figure) as this may result in 
paper jams. [Note that the unit can hold 
about 40 sheets of paper having a weight of 
80 g/m
2 (20 lb.).]
4
Close the paper cover until a click is heard.
Note
•Close the...

Setting the Electronic Pen and Eraser
25
Using
1
Remove the battery cover on the pen holder, 
insert the batteries as shown in the figure, and 
re-attach the battery cover.
•Always use “LR03 (AAA size)” (alkaline) 
batteries and be sure that their polarity is 
properly oriented.
•Do not mix old and new, different type 
batteries when replacing batteries.
2
Remove the temporal cap, and set the cap 
and adaptor to the marker for interactive.
•Securely push the adaptor into the marker 
for interactive as...

Setting the Electronic Pen and Eraser
26
1
Remove the eraser cover, insert the batteries 
as shown in the figure, and re-attach the 
eraser cover.
•Always use “LR03 (AAA size)” (alkaline) batteries 
and be sure that their polarity is properly oriented.
•Do not mix old and new, different type batteries 
when replacing batteries.
Note
•Press down firmly with the eraser cloth of the 
Electronic Eraser on the screen film until you 
hear a buzzing sound.
1
Remove the eraser cloth by pushing through 
the hole...

Installing Drivers and Software
27
Using
Drivers and software must be installed in your 
computer to use the interactive function, printer and 
TWAIN driver.
For the information of the interactive function and 
Panasonic-DMS, refer to “Features” on page 4.
*1This electronic board does not function with Hi-Speed 
USB 2.0. Even if using a computer equipped with Hi-
Speed USB 2.0, this electronic board functions with 
Full Speed USB 2.0.
*
2Microsoft Windows 98 operating system 
(hereafter Windows 98)
*...

Installing Drivers and Software
28
The USB, printer, TWAIN driver and Interactive 
Panaboard Software are installed in your computer 
by following procedures.
Note
•Do not yet connect a USB cable to the 
electronic board.
1Power on your computer and start Windows*1.
•Log on as an administrator for 
Windows 2000 
or Windows XP.
*
1Microsoft Windows operating system 
(hereafter Windows)
2Insert the CD-ROM into the CD-ROM drive. 
The Setup window appears automatically.
•Depending on the operating system...

Installing Drivers and Software
29
Using
8When the following window appears after files 
are copied, power the electronic board on, 
and connect the USB cable provided from the 
electronic board to your computer.
9Follow the on-screen instructions if the wizard 
windows appear.
•If the wizard window is displayed to select 
the file (##.inf) for the printer driver in 
Windows XP, select “windows\inf\oem##.inf”.
•If the wizard window is displayed to connect 
to the Windows Update in Windows XP SP2, 
select...

Installing Drivers and Software
30
When Panasonic-DMS is already installed, leave it 
(do not uninstall it) and install the new software in 
the same folder to overwrite it.
1Power on your computer and start Windows.
•Log on as an administrator for 
Windows 2000 or Windows XP.
2Insert the CD-ROM into the CD-ROM drive.
The Setup window appears automatically.
•Depending on the operating system or the 
settings that you are using, the Setup 
window may not appear automatically. 
In such a case, double-click...